Model-based analysis of the surface generation in microendmilling - Part I: Model development

Journal of Manufacturing Science and Engineering

Volumn 129, Issue 3, 2007, Pages 453-460

  Liu, Xinyu ^a   DeVor, Richard E ^a   Kapoor, Shiv G ^a  

^a University of Illinois at Urbana Champaign   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EDGE DETECTION; INVERSE KINEMATICS; MILLING (MACHINING); SURFACE PROPERTIES; SURFACE ROUGHNESS;

CHIP THICKNESS; DETERMINISTIC MODELS; ELASTIC RECOVERY; MICROENDMILLING;

STOCHASTIC MODELS;

EID: 34547407362     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2716705     Document Type: Article

References (12)

1. Friedrich, C. R., and Kang, S. D., 1994, "Micro Heat Exchangers Fabricated by Diamond Machining," Precis. Eng., 16, pp. 56-59.
2. Adams, D. P., Vasile, M. J., Benavides, G., and Campbell, A. N., 2001, "Micromilling of Metal Alloys With Focused Ion Beam Fabricated Tools," Precis. Eng., 25, pp. 107-113.
3. Liu, X., Jun, M., DeVor, R. E., and Kapoor, S. C., 2004, "Cutting Mechanisms and Their Influence on Dynamic Forces, Vibrations and Stability in Micro-Endmilling," Proc. of ASME International Mechanical Engineering Congress and Exposition, ASME, New York, pp. 583-592.
4. Vogler, M. P., DeVor, R. E., and Kapoor, S. G., 2004, "On the Modeling and Analysis of Machining Performance in Microendmilling, Part I: Surface Generation," ASME J. Manuf. Sci. Eng., 126(4), pp. 685-694.
5. Weule, H., Huntrup, V., and Trischle, H., 2001, "Micro-Cutting of Steel to Meet New Requirements in Miniaturization," CIRP Ann., 50, pp. 61-64.
6. Kim, C. J., Bono, M., and Ni, J., 2002, "Experimental Analysis of Chip Formation in Micro-Milling," Trans. North Am. Manuf. Res. Inst. SME, 30, pp. 1-8.
7. Vogler, M. P., DeVor, R. E., and Kapoor, S. G., 2004, "On the Modeling and Analysis of Machining Performance in Microendmilling, Part II: Cutting Force Prediction," ASME J. Manuf. Sci. Eng., 126(4), pp. 695-705.
8. Liu, X., DeVor, R. E., and Kapoor, S. G., 2007, "Model-Based Analysis of the Surface Generation in Microendmilling-Part II: Experimental Validation and Analysis," ASME J. Manuf. Sci. Eng., 129(3), pp. 461-469.
9. Merdol, S. D., and Altintas, Y., 2002, "Mechanics and Dynamics of Serrated End Mills," Proc. of ASME International Mechanical Engineering Congress and Exposition, ASME, New York, pp. 337-342.
10. Park, S., Kapoor, S. G., and DeVor, R. E., 2006, "Microstructure- Level Model for the Prediction of Tool Failure in WC-CO Cutting Tool Materials," ASME J. Manuf. Sci. Eng., 128(3), pp. 739-748.
11. Koshy, P., Jain, V. K., and Lal, G. K., 1993, "A Model for the Topography of Diamond Grinding Wheels," Wear, 169(2), pp. 237-242.
12. Stout, K. J., Sullivan, P. J., Dong, W. P., Mainsah, E., Mathia, T., and Zahouani, H., 1993, "The Development of Methods for the Characterization of Roughness in Three Dimensions," Publication No. EUR 15178 EN of the Commission of the European Communities, pp. 1-358.