Experimental study and evaluation methodology on hard surface integrity

International Journal of Advanced Manufacturing Technology

Volumn 34, Issue 1-2, 2007, Pages 141-148

  Zhang, Xueping ^a   Liu, C Richard ^b   Yao, Zhenqiang ^a  

^a SHANGHAI JIAO TONG UNIVERSITY   (China)

^b SCHOOL OF INDUSTRIAL ENGINEERING   (United States)

Author keywords

Hard dry turning; Optimization methodology; Surface integrity; Turning parameter

Indexed keywords

HARD DRY TURNING; OPTIMIZATION METHODOLOGY; SURFACE INTEGRITY; THERMAL DAMAGE; TURNING PARAMETERS;

OPTIMIZATION; PARAMETER ESTIMATION; RESIDUAL STRESSES; STEEL; SURFACE ROUGHNESS; TAGUCHI METHODS;

SURFACE CHEMISTRY;

EID: 34547206013     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-006-0575-6     Document Type: Article

References (17)

1. Liu CR, Mittal S (1995) Single-step superfinish hard machining: feasibility and feasible cutting condition. Robotic Compute Int Manuf 12(1):15-27
2. Tönshoff HK, Arendt R, Ben Amor C (2000) Cutting of hardened steel. Ann CIRP 49(2):547-566
3. Rech J, Moisan A (2003) Surface integrity in finish hard turning of case-hardened steels. Int J Mach Tools Manuf 43:543-550 (France)
4. Chou YK, Evans CJ (1999) White layers and thermal modeling of hard turned surfaces. Int J Mach Tools Manuf 39(2):1863-1881
5. Liu CR, Guo YB (2000) Finite element analysis of the effect of sequential cuts and tool-chip friction on residual stresses in a machined layer. Int J Mech Sci 42:1069-1086
6. Jacobson M, Dahlman P, Gunnberg F (2002) Cutting speed influence on surface integrity of hard turned bainite steel. J Mater Technol 128:318-323
7. Che-Haron CH (2001) Tool life and surface integrity in turning titanium alloy. J Mater Process Technol 118:231-237
8. Abrao AM, Aspinwall DK (1996) The surface integrity of turned and ground hardened bearing steel. Wear 196:279-284
9. Sasahara H, Obikawa T, Shirakashi T (1996) FEM analysis of cutting sequence effect on mechanical characteristics in machined layer. J Mater Process Technol 62:448-453
10. Liu XL, Wen DH, Li ZJ et al (2002) Experimental study on hard turning hardened GCr15 steel with PCBN tool. J Mater Process Technol 129:217-221
11. Liu CR, Mittal S (1995) Single-step superfinish using hard machining resulting in superior surface integrity. J Manuf Syst 14(2):124-133
12. Yang WH, Tarng YS (1998) Design optimization of cutting parameters for turning operations based on the Taguchi method. J Mater Process Technol 84:122-129
13. Noyan IC, Cohen JB (1987) Residual stress: measurement by diffraction and interpretation. Springer, Berlin Heidelberg New York
14. Agha Salah R, Liu CR (2000) Experimental study on the performance of superfinish hard turned surfaces in rolling contact. Wear 244(6):52-59
15. Liu CR, Mittal S (1998) Optimal pre-stressing the surface of a component by superfinish hard turning for maximum fatigue life in rolling contact. Wear 219:128-140
16. Zhang XP, Liu CR, Yao ZQ (2004) Investigational advances in residual stresses by hard turning. Mater Sci Forum 471-472(9):523-527
17. Zhang XP, Liu CP, Liu LQ (2004) A methodology for turning parameters selection of rolling bearing in superfinish hard turning. J Shanghai Jiaotong Univ 38:1101-1104