Comparative evaluation of conventional and wiper ceramic tools on cutting forces, surface roughness, and tool wear in hard turning AISI D2 steel

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture

Volumn 221, Issue 4, 2007, Pages 625-633

  Paulo Davim, J ^a   Figueira, L ^a  

^a UNIVERSITY OF AVEIRO   (Portugal)

Author keywords

Cutting forces; Flank wear; Hard turning; Surface roughness; Wiper ceramic tools

Indexed keywords

ANALYSIS OF VARIANCE (ANOVA); CUTTING; CUTTING TOOLS; MACHINABILITY; STEEL; SURFACE ROUGHNESS; WEAR OF MATERIALS;

CUTTING FORCES; HARD TURNING; MACHINABILITY PARAMETERS; TOOL WEAR;

CERAMIC TOOLS;

EID: 34250215946     PISSN: 09544054     EISSN: None     Source Type: Journal    
DOI: 10.1243/09544054JEM762     Document Type: Article

References (13)

1. Hua, J., Shivpuri, R., Cheng, X., Bedekar, V., Matsumoto, Y., Hashimoto, F., and Watkins, T. R. Effect of feed rate, workpiece hardness and cutting edge on subsurface residual stress in the hard turning of bearing steel using chamfer + hone cutting edge geometry. J. Mater. Sci. Engng, 2005, 394, 238-248.
2. Lima, J. G., Avila, R. F., Abrao, A. M., Faustino, M., and Paulo Davim, J. Hard turning: AISI 4340 high strength low alloy steel and AISI D2 cold work tool steel. J. Mater. Processing Technol., 2005, 169, 388-395.
3. Barry, J. and Byrne, G. Cutting tool wear in the machining of hardened steels - Part I: alumina/TiC cutting tool wear. Wear, 2001, 247, 139-151.
4. Barry, J. and Byrne, G. Cutting tool wear in the machining of hardened steels - Part II: cubic boron nitride cutting tool wear. Wear, 2001, 247, 152-160.
5. Chou, Y. K., Evans, C. J., and Barash, M. M. Experimental investigation on cubic boron nitride turning of hardened AISI 52100 steel. J. Mater. Processing Technol., 2003, 134, 1-9.
6. Chou, Y. K. and Song, H. Tool nose radius effects on finish hard turning. J. Mater. Processing Technol., 2004, 148 (2), 259-268.
7. Luo, S. Y., Liao, Y. S., and Tsai, Y. Y. Wear characteristics in turning high hardened alloy steel by ceramic and CBN tools. J. Mater. Processing Technol., 1999, 88, 114-121.
8. Rech, J. and Moisan, A. Surface integrity in finish hard turning of case-hardened steels. Int. J. Machine Tools Mf., 2003, 43, 543-550.
9. Bourithis, L., Papadimitriou, G. D., and Sideris, J. Comparison of wear properties of tool steels AISI D2 and O1 with the same hardness. Tribology Int., 2006, 39, 479-489.
10. Paulo Davim, J. and Figueira, L. Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques. Mater. Des., 2007, 28, 1186-1191.
11. Grzesik, W. and Wanat, T. Comparative assessment of surface roughness produced by hard machining with mixed ceramic tools including 2D and 3D analysis. J. Mater. Processing Technol., 2005, 169, 364-371.
12. Grzesik, W. and Wanat, T. Surface finish generated in hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts. Int. J. Mach. Tools Mf, 2006, 46(15), 1988-1995.
13. Krishnamurthy, R. and Gokularathnam, C. V. Phase transformation toughened materials for cutting tool applications. In Ceramica cutting tools (Ed. E. Dow Whitney) 1994, pp. 120-121 (Noyes Publications).