Surface and edge quality variation in precision machining of single crystal and polycrystalline materials

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture

Volumn 220, Issue 4, 2006, Pages 479-487

  Min, S ^a,d   Lee, D E ^a   De Grave, A ^b   De Oliveira Valente, C M ^c   Lin, J ^a   Dornfeld, D A ^a  

^a UNIVERSITY OF CALIFORNIA   (United States)

^b LABORATOIRE SOLS SOLIDES STRUCTURES   (France)

^c UNIVERSITY OF SÃO PAULO   (Brazil)

^d UNIVERSITY OF CALIFORNIA   (United States)

Author keywords

Crystallographic orientation effect; Micromachining; Surface and edge quality

Indexed keywords

COPPER; CRYSTAL ORIENTATION; MICROSTRUCTURE; POLYCRYSTALLINE MATERIALS; PRECISION ENGINEERING; SINGLE CRYSTALS;

CRYSTALLOGRAPHIC ORIENTATION EFFECT; EDGE QUALITY; SURFACE QUALITY;

SURFACE MICROMACHINING;

EID: 34247113797     PISSN: 09544054     EISSN: None     Source Type: Journal    
DOI: 10.1243/095440506X77599     Document Type: Article

References (14)

1. Schaller, Th., Bohn, L., Mayer, J., and Schubert, K. Microstructure grooves with a width of less than 50 μm cut with ground hard metal micro end mills. Precision Engng, 1999, 23, 229-235.
2. Lee, K., Ahn, S., Dornfeld, D. A., and Wright, P. K. The effect of run-out on design for manufacturing in micromachining process. In Proceedings of the ASME International Mechanical Engineering Congress and Exposition, New York, USA, November 2001 (American Society of Mechanical Engineers, New York).
3. Rahman, M., Kumar, A. S., and Prakash, J. R. S. Micro milling of pure copper. J. Mater. Processing Technol., 2001, 116, 39-43.
4. Moriwaki, T., Sugimura, N., and Luan, S. Combined stress, material flow and heat analysis of orthogonal micromachining of copper. Ann. CIRP, 1993, 42(1), 75-78.
5. Weule, H., Schmidt, J., Hüntrup, V., and Tritschler, H. Micromilling of ferrous materials. Prod. Engng, 1999, 6(2), 17-20.
6. Moriwaki, T. Experimental analysis of ultra-precision machining. Int. J. Japan Soc. Precision Engng, 1995, 29(4), 287-290.
7. Ueda, K. and Iwata, K. Chip formation mechanism in single crystal cutting of ß brass. Ann. CIRP, 1980, 29(1), 41-16.
8. Sato, M., Yamazaki, T., Shimizu, Y., and Takabayashi, T. A study on the microcutting of aluminum single crystals. JSME Int. J. Ser. III, 1991, 34(4), 540-545.
9. Yuan, Z., Lee, W., Yao, Y., and Zhou, M. Effect of crystallographic orientations on cutting forces and surface quality in diamond cutting of single crystal. Ann. CIRP, 1994, 43(1), 39-42.
10. Gillespie, L. K. Burrs produced by drilling. Unclassified topical report BDX-613-1248, Bendix Corporation 1975.
11. Miyake, T., Yamamoto, A., Kitajima, K., Tanaka, Y., and Takazawa, K. Study on mechanism of burr formation in drilling: deformation of material during burr formation. J. Japan Soc. Precision Engng, 1991, 57(3), 485-490.
12. Min, S., Kim, J., and Dornfeld, D. A. Development of a drilling burr control chart for low alloy steel. AISI 4118. J. Mater. Processing Technol., 2001, 113(1-3), 4-9.
13. Min, S., Kim, J., and Dornfeld, D. A. Thrust force analysis of drilling burr formation using finite element method. In Proceedings of the Tenth International Conference on Precision engineering, Yokohama, Japan, 2001, pp. 169-173.
14. Kim, J., Min, S., and Dornfeld, D. A. Optimization and control of drilling burr formation of AISI 304L and AISI 4118 based on drilling burr control charts. Int. J. Mach. Tools Mf., 2001, 41(7), 923-936.