Evaluation and analysis of residual stresses due to foreign object damage

Mechanics of Materials

Volumn 39, Issue 3, 2007, Pages 199-211

  Duo P ^a   Liu, J ^a   Dini, D ^a   Golshan, M ^b   Korsunsky, A M ^a  

^a UNIVERSITY OF OXFORD   (United Kingdom)

^b DARESBURY LABORATORY   (United Kingdom)

Author keywords

FOD; Foreign object damage; High strain rate impact; Residual stresses; Ti6Al4V

Indexed keywords

CRACK INITIATION; CRACK PROPAGATION; GAS TURBINES; INGESTION (ENGINES); LOADS (FORCES); PARTICLES (PARTICULATE MATTER); SAND; X RAY DIFFRACTION;

FOREIGN OBJECT DAMAGE (FOD);

RESIDUAL STRESSES;

EID: 33846013893     PISSN: 01676636     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.mechmat.2006.05.003     Document Type: Article

References (25)

1. Bammann D.J., and Aifantis E.C. A model for finite-deformation plasticity. Acta Mech. 69 (1987) 97-117
2. Bammann D.J., Chiesa M.L., Horstemeyer M.F., and Weingarten L.I. Failure in ductile materials using finite element methods. In: Jones N., and Wierzbicki T. (Eds). Structural Crahsworthiness and Failure (1993), Elsevier Applied Science, London
3. Bruker AXS, 2002. StressPLUS software and Users Guide Manuals.
4. Collins S.P., Murphy B.M., Tang C.C., Miller M.C., and Oszlanyi G. J. Phys. D: Appl. Phys. 32 (1999) A81-A83
5. Cullity B.D., and Stock S.R. Elements of X-Ray Diffraction. third ed. (2001), Prentice Hall, London
6. Duó, P., 2005. A predictive study of foreign object damage in gas turbine compressor blades under high cycle fatigue. DPhil Thesis, University of Oxford.
7. Duó, P., Nowell, D., 2004. Predictive numerical modeling of foreign object damage. In: 8th International LS-DYNA Users Conference.
8. Duó, P., Nowell, D., Stewart, I.F., 2003. The role of FOD in decreasing the residual fatigue strength of Ti6Al4V compressor blades. In: Proceedings of the 8th High Cycle Fatigue Conference, Monterey, CA.
9. Duó, P., Nowell, D., Schofield, J. 2004. Assessment of foreign object damage (FOD) to aero engine blades. In: Proceeding of the 9th National Turbine Engine HCF Conference, Pinehurst, NC.
10. Duó, P., Nowell, D., Oakley, S.Y., Petrinic, N., Schofield, J., 2005. Prediction and experimental validation of fatigue strength following Foreign Object Damage. NATO, Evaluation, Control and Prevention of High Cycle Fatigue in Gas Turbine Engines for Land, Sea and Air Vehicles, RTO-MP-AVT-121, Granada, Spain.
11. El Haddad M.H., Topper T.H., and Smith K.N. Prediction of non-propagating cracks. Eng. Fracture Mech. 11 (1979) 573-584
12. Hudak Jr., S.J., Chell, G.G., Rennick, T.S., McClung, R.C., Davidson, D.L., 1999. A damage tolerance approach to fod based on the 'worst case notch' concept. In: Proceeding 4th National Turbine Engine High Cycle Fatigue Conference, Monterey, CA.
13. Kitagawa, H., Takahashi, S., 1976. Applicability of fracture mechanics to very small cracks or cracks in the early stage. In: Proceedings of the 2nd International Conference on Mechanical behaviour of Materials, ASM, pp. 627-631.
14. Korsunsky A.M., Collins S.P., Owen R.A., Daymond M.R., Achtioui S., and James K.E. J. Synchrotron Rad. 9 (2002) 77-81
15. Korsunsky, A.M., Regino, G.M., Nowell, D., 2004. Variational determination of eigenstrain sources of residual stress. In: Intl. Conf. Comp. Engng. Sci. Madeira.
16. Kroner E. Berechnung der elastischen Konstanten des Vielkristalls aus den Konstanten des Einkristalls. Z. Phys. 151 (1958) 504
17. Larson, A.C., Von Dreele, R.B., 2000. General Structure Analysis System (GSAS). Los Alamos National Laboratory Report LAUR 86-748.
18. LSTC, 2004. Livermore Software Technologies Corporation. LS-DYNA User's Guide.
19. Mall S., Hamrick II J.L., and Nicholas T. High cycle fatigue behavior of Ti-6Al-4V with simulated foreign object damage. Mech. Mater. 33 11 (2001) 679-692
20. Noble J.P., Goldthorpe B.D., Church P., and Harding J. The use of the Hopkinson bar to validate constitutive relations at high rates of strain. J. Mech. Phys. Solids 47 5 (1999) 1187-1206
21. Nowell D., Duó P., and Stewart I.F. Prediction of fatigue performance in gas turbine blades after foreign object damage. Int. J. Fatigue 25 (2003) 963-969
22. Prevéy P.S. X-ray Diffraction Residual Stress Techniques, Metals Handbook vol. 10 (1986), American Society for Metals, New York pp. 380-392
23. Prevéy, P., Jayaraman, N., Shepard, M., 2004. Improved HCF performance and FOD tolerance of surface treated Ti-6-2-4-6 compressor blades. In: Proceedings 9th National HCF Conference, Pinehurst, NC.
24. Toby T.B.H. EXPGUI, a graphical user interface for GSAS. J. Appl. Cryst. 34 (2001) 210-211
25. Tranter, P.H., Gould, P.J., Harrison, G.F., 2003. Laboratory simulation and finite element modelling of aerofoil impact damage. In: Proceedings of the 8th High Cycle Fatigue Conference, Monterey, CA.