Three dimensional modeling weld solidification cracks in multipass welding

Theoretical and Applied Fracture Mechanics

Volumn 46, Issue 2, 2006, Pages 156-165

  Dong, Z B ^a   Wei, Y H ^b  

^a HARBIN INSTITUTE OF TECHNOLOGY   (China)

^b NANJING UNIVERSITY OF AERONAUTICS AND ASTRONAUTICS   (China)

Author keywords

[No Author keywords available]

Indexed keywords

CRACKS; DEFORMATION; FLOW OF FLUIDS; MATHEMATICAL MODELS; SOLIDIFICATION; STRAIN; WELDING; WELDS;

DRIVING FORCE; MULTIPASS WELDING; SOLIDIFICATION CRACKS; WELD SOLIDIFICATION;

STAINLESS STEEL;

CRACKS; DEFORMATION; FLOW OF FLUIDS; MATHEMATICAL MODELS; SOLIDIFICATION; STAINLESS STEEL; STRAIN; WELDING; WELDS;

EID: 33748415012     PISSN: 01678442     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.tafmec.2006.07.007     Document Type: Article

References (20)

1. Liang Teng T., and Chang P.H. A study of residual stresses in multi-pass girth-butt welded pipes. Int. J. Pres. Ves. Piping 74 (1997) 59-70
2. Duranton P., Devaus J., and Robin V. 3D modelling of multipass welding of a 316L stainless steel pipe. J. Mater. Proc. Technol. 153 (2004) 457-463
3. Brickstad B., and Josefson B.L. A parametric study of residual stresses in multi-pass butt-welded stainless steel pipes. Int. J. Pre. Ves. Piping 75 (1998) 11-25
4. Elcoate C.D., Dennis R.J., and Bouchard P.J. Three dimensional multi-pass repair weld simulation. Int. J. Pre. Ves. Piping 82 (2005) 244-257
5. Bouchard P.J., and George D. Measurement of the residual stresses in a stainless steel pipe girth weld containing long and short repairs. Int. J. Pre. Ves. Piping 105 (2004) 81-91
6. Shim Y. Determination of residual stresses in thick-section weldments. Weld. J. 71 (1992) 305-312
7. Murugan S., Sanjai K., Rai B., and Kumar P.V. Temperature distribution and residual stresses due to multipass welding in type 304 stainless steel and low carbon steel weld pads. Int. J. Pre. Ves. Piping 78 (2001) 307-317
8. Cho J.R., Lee B.Y., and Moon Y.H. Investigation of residual stress and post weld heat treatment of multi-pass welds by finite element method and experiments. J. Mater. Proc. Technol. 154 (2004) 1690-1695
9. A.R. Ortega, Analysis and validation of multi-pass girth in pipes, in: 8th Int. Conf. of Casting, June 779-786, 998, San Diego, USA.
10. Pang H.L., and Pukas S.R. Residual stress measurements in a Crusi-form welded joint using hole drilling and strain gauges. Strain 2 (1989) 7-14
11. Feng Z.L., Zagharia T., and David S.A. Thermal stress development in a nickel based superalloy during weldability test. Weld. J. 76 (1997) 470-483
12. Feng Z.L., and Tsai C.L. A computational analysis of thermal and mechanical conditions for weld metal solidification cracking. Weld. Res. Abroad 42 (1996) 34-41
13. H. Bergmann, R. Hilbinger, Numerical simulation of centre line hot cracks in laser beam welding of aluminium close to the sheet edge, in: Mathematical Modelling of Weld Phenomena 4, Graz, Austria, 1998.
14. J. Dike, J. Brooks, J. Krafcik, Finite element modeling and verification of thermal-mechanical behavior in the weld pool region, in: 4th International Conference on Trends in Welding Research. Gatlinburg, USA, 1995.
15. Wei Y.H., and Dong Z.B. Three dimensional numerical simulation of weld solidification cracking. Model. Simul. Mater. Sci. 13 (2005) 437-454
16. Dong Z.B., and Wei Y.H. Three dimensional numerical simulation of the driving force to solidification cracking. J. Mater. Sci. Technol. 21 (2005) 399-402
17. Wei Y.H., and Dong Z.B. Modeling the trans-varestraint test with finite element method. Comput. Mater. Sci. 35 (2006) 84-91
18. Goldak J. A new finite element model for welding heat sources. Metall. Trans. 15B (1984) 299-305
19. Murugan S., Kumar P.V., and Raj B. Temperature distribution during multi-pass welding plates. Int. J. Pre. Ves. Piping 75 (1998) 891-905
20. F. Matsuda, H. Nakagawa, Quantitative evaluation of solidification brittleness of weld metal during solidification by means of in situ observation and measurement.