An experimental investigation on wear aspects of tapping operation on hardened steels

Machining Science and Technology

Volumn 10, Issue 2, 2006, Pages 235-250

  Coelho, Reginaldo Teixeira ^a   Arai, Ricardo ^a   Watanuki, Hugo Martinelli ^a   Borges, Emanuel ^a  

^a UNIVERSITY OF SÃO PAULO   (Brazil)

Author keywords

AISI D2; AISI H13; Hardened Steel; Tapping; Threading; Wear

Indexed keywords

CARBIDES; DEFECTS; STEEL; TAPPING (THREADS); THREAD CUTTING;

AISI D2; AISI H13; HARDENED STEEL; THREADING;

WEAR OF MATERIALS;

EID: 33745120509     PISSN: 10910344     EISSN: 15322483     Source Type: Journal    
DOI: 10.1080/10910340600710097     Document Type: Article

References (13)

1. Cao, T. and Sutherland, J.W. (2002). Investigation of Thread Tapping Load Characteristics Through Mechanistic Modeling and Experimentation. International Journal of Machine, Tools & Manufacture, 42:1527-1538.
2. Mezentsev, O.A., Zhu, R., DeVor, R.E., Kapoor, S.G., and Kline, W.A. (2002). Use of Radial Forces for Fault Detection in Tapping. International Journal of Machine Tools & Manufacture, 42:479-488.
3. Li, W., Li, D., and Ni, J, (2003). Diagnosis of Tapping Process Using Spindle Motor Current. International Journal of Machine Took & Manufacture, 43:73-79.
4. Zhang, D.Y. and Chen, D.C. (1998). Relief-Face Friction in Vibration Tapping. Int. J. Mech. Sci., 40 (12): 1209-1222.
5. Barry, J. and Byrne, G. (2001). Cutting Tool Wear in the Machining of Hardened Steels Part I: alumina/TiC Cutting Tool Wear. Wear, 247:139-151.
6. Barry, J. and Byrne, G. (2001). Cutting Tool Wear in the Machining of Hardened Steels Part II: Cubic Boron Nitride Cutting Tool Wear. Wear, 247:152-160.
7. Tonshoff, H.K., Arendt, C.R., and Ben Amor, R. (2000). Cutting Hardened Steels. Ann. CIRP, 49 (2): 32-41.
8. Chou, Y.K. (1997). Tool Wear Mechanism in Continuous Cutting of Hardened Tool Steels. Wear, 212:59-65.
9. Abrão, A.M. and Aspinwall, D.K. (1996). The Surface Integrity of Turned and Ground Hardened Bearing Steel. Wear, 196:279-284.
10. Derflinger, V., Brändie, H., and Zimmermann, H. (1999). New Hard/Lubricant Coating for Dry Machining. Surface and Coatings Technology, 113:286-292.
11. Haigang, C., Xuedong, W., Shengrong, Y, Ling, Z., and Dapu, W. (2001). The Tribological Behaviors of Various Metallic Cations in Tapping of a Titanium Alloy. Wear, 247:120-123.
12. Arndt, M. and Kacsich, T. (2003). Performance of New AlTiN Coatings in Dry and High Speed Cutting. Surface and Coatings Technology, 163-164:674-680.
13. Agapiou, J.S. (1994). Evaluation of the Effect of High Speed Machining on Tapping. Transactions of the ASME - Journal of Engineering for Industry, 116(4):457-462.