Spray cooling of small-pitched, straight-finned, copper heat sinks

American Society of Mechanical Engineers, Heat Transfer Division, (Publication) HTD

Volumn 376 HTD, Issue 2, 2005, Pages 271-277

  Coursey, Johnathan S ^a   Kim, Jungho ^a   Kiger, Kenneth T ^a  

^a UNIVERSITY OF MARYLAND   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CRITICAL HEAT FLUX (CHF); SINGLE-PHASE REGIME; SPRAY COOLING;

COOLING; DIELECTRIC LIQUIDS; FINS (HEAT EXCHANGE); HEAT FLUX; POWER ELECTRONICS; SPRAYING;

HEAT SINKS;

EID: 33645718811     PISSN: 02725673     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/IMECE2005-81210     Document Type: Conference Paper

References (15)

1. Chen, J.C. (1966), "Correlation for boiling heat transfer to saturated fluids in convective flow," Ind. Eng. Chem. Proc. Design and Dev., Vol. 5(3), p. 322-339.
2. Chow, L.C., Sehmbey, M.S., and Pais, M.R. (1997) "High-Heat-Flux Spray Cooling," Annual Review of Heat Transfer, 8, p. 291-318.
3. Chen, R.C., Chow, L.C., Navedo, J.E. (2002), "Effects of Spray Characteristics on Critical Heat Flux in Subcooled Water Spray Cooling", International Journal of Heat and Mass Transfer, Vol. 45, p. 4033-4043.
4. Estes, K.A. and Mudawar, I. (1995), "Comparison of Two-phase Electronic Cooling Using Free Jets and Sprays", Journal of Electronic Packaging, Vol. 117, p. 323-332.
5. Kendall, C.M. and Holman, J.P. (1996), "Spray Cooling Heat-Transfer with Subcooled Trichlorotrifluoroethane (Freon-113) for Vertical Constant Heat Flux Surfaces", HTD-Vol 333, Proceedings of the ASME Heat Transfer Division, Vol. 2.
6. Horacek, B., Kim, J., and Kiger, K. (2004) "Spray Cooling Using Multiple Nozzles: Visualization and Wall Heat Transfer Measurements", IEEE Transactions on Device and Materials Reliability, Vol. 4(4), p. 614-625.
7. Horacek, B., Kiger, K., Kim, J. (2005) "Single Nozzle Spray Cooling Heat Transfer Mechanisms", International Journal of Heat and Mass Transfer, Vol. 48(8), p. 1425-1438.
8. Lin, L. and Ponnappan, R. (2002), "Heat transfer characteristics of an evaporative spray cooling in a closed loop", Proceedings of the 2002 SAE Power Systems Conference, Coral Springs, FL, SAE Paper No. 2002-01-3198.
9. Ortiz, L. and Gonzalez, J.E. (1999), "Experiments on Steady-State High Heat Fluxes Using Spray Cooling", Experimental Heat Transfer, Vol. 12, p. 215-233.
10. Pais, M.R, Chow, L.C., and Mahefkey, E.T. (1992), "Surface roughness and its effects on the heat transfer mechanism in spray cooling", Journal of Heat Transfer, Transactions ASME, Vol. 114(1), p. 211-219.
11. Pautsch, A.G, and Shedd, T.A. (2005), "Spray Impingement Cooling with Single- and Multiple-nozzle Arrays. Part I: Heat Transfer Data Using FC-72," Int. J. Heat Mass Trans., Vol. 48, p. 3167-3175.
12. Silk, E. A., Kim, J., Kiger, K. (2004), "Investigation of Enhanced Surface Spray Cooling," Proceedings of IMECE04 2004 ASME International Mechanical Engineering Congress and Exposition November 13-20, 2004, Anaheim, California USA. IMECE2004-61753
13. Silk, E. A., Kim, J., Kiger, K. (2005), "Spray Cooling Trajectory Angle Impact Upon Heat Flux Using a Straight Finned Enhanced Surface," Proceedings of HT2005: ASME 2005 Heat Transfer Summer Conference July 17-22, 2005, San Francisco, CA, USA. HT2005-72634
14. Tilton, D.E., Tilton, C.L, Pais, M.R., and Morgan, M.J. (1992) "High-Flux Spray Cooling in a Simulated Multichip Module", HTD-Vol. 206-2, Proceedings of the 1992 ASME Heat Transfer Conference.
15. Yang, J.D., Chow, L.C., and Pais, M.R. (1996) "Nucleate Boiling Heat Transfer in Spray Cooling," Journal of Heat Transfer, Vol. 118, p. 668-671.