Mixed rheologies in elastohydrodynamic lubrication

Industrial Lubrication and Tribology

Volumn 56, Issue 2, 2004, Pages 88-106

  Zhang, Y ^a  

^a Shanxi Institute of Technology   (China)

Author keywords

Boundary layers; Lubrication; Rheology

Indexed keywords

ELASTIC MODULI; INTERFACES (MATERIALS); MATHEMATICAL MODELS; RHEOLOGY; SHEAR STRENGTH; VISCOELASTICITY; VISCOPLASTICITY;

LINE CONTACTS; ROLLING SPEED; SLIDE ROLL RATIOS;

ELASTOHYDRODYNAMIC LUBRICATION;

EID: 3242693082     PISSN: 00368792     EISSN: None     Source Type: Journal    
DOI: 10.1108/00368790410524047     Document Type: Article

References (22)

1. Bailey, M.W. and Cameron, A. (1973), "The effects of temperature and metal pairs on scuffing", ASLE Trans., Vol. 16, p. 121.
2. Conry, T.F., Wang, S. and Cusano, C. (1987), "A Reynolds-Eyring equation for elasto hydrodynamic lubrication in line contacts", ASME J. of Trib., Vol. 109, pp. 648-58.
3. Czichos, H. (1974), "Failure modes of sliding lubricated concentrated contacts", Wear, Vol. 28, pp. 95-101.
4. Czichos, H. and Kirschke, K. (1972), "Investigations into film failure (transition point) of lubricated concentrated contacts", Wear, Vol. 22, pp. 321-36.
5. Dowson, D. and Higginson, G.R. (1977), Elastohydrodynamic Lubrication, Pergamon Press, Oxford.
6. Ehret, P., Dowson, D. and Taylor, C.M. (1998), "On lubricant transport conditions in elastohydrodynamic conjunctions", Proc. Roy. Soc. tond., Vol. A454, pp. 763-87.
7. Israelachvili, J. (1991), Intermolecular & Surface Forces, 2nd ed., Academic Press, Dublin.
8. Kaneta, M. and Nishikawa, H. (1992), "Effects of elastic moduli of contact surfaces in elastohydrodynamic lubrication", ASME J. of Trib., Vol. 114, pp. 75-80.
9. Kannel, J.W. and Bell, J.C. (1971), "Interpretations of the thickness of lubricant films in rolling contact: part I - examination of measurements obtained by X-Rays", ASME J. of Lubri. Tech., pp. 478-84.
10. Murch, L. and Wilson, W.R.D. (1975), "A thermal elastohydrodynamic inlet zone analysis", ASME J. of Lubri. Tech., pp. 212-6.
11. Rozeanu, L. (1980), "Slippage phenomena at the interface between the absorbed layer and the bulk of the lubricant theory and experiment", Wear, Vol. 64, pp. 245-57.
12. Rozeanu, L. and Snarsky, L. (1978), "Effect of solid surface lubricant interaction on the load carrying capacity of sliding bearings", ASME J. of Lubri. Tech., Vol. 100, pp. 167-75.
13. Salomon, G. (1976), "Failure criteria in thin film lubricationthe IRG program", Wear, Vol. 36, pp. 1-6.
14. Sharma, J. and Cameron, A. (1973), "Surface roughness and load in boundary lubrication", ASLE Trans., Vol. 16 No. 4, pp. 258-66.
15. Zhang, Y (n.d), "Prevention of film slippage in pure rolling line contact elastohydrodynamic lubrication at heavy loads", Proc. Instn. Mech. Engrs., Part J- Engineering Tribology.
16. Zhang, Y. and Wen, S. (2000), "EHL performance of the lubricant with shear strength: part i - boundary slippage and film failure", Trib. Trans., Vol. 43, pp. 700-10.
17. Zhang, Y. and Wen, S. (2001a), "A lubrication deviation from the classical EHL theory by the lubricant viscoplastidty: part I - film thickness dependence", Trib. Trans., Vol. 44, pp. 224-32.
18. Zhang, Y. and Wen, S. (2001b), "A lubrication deviation from the classical EHL theory by the lubricant viscoplastidty: part II - boundary of lubrication regimes", Trib. Trans., Vol. 44, pp. 305-9.
19. Zhang, Y. and Wen, S. (2002a), "An analysis of elastohydrodynamic lubrication with limiting shear stress: part I - theory and solutions", Trib. Trans., Vol. 45, pp. 135-44.
20. Zhang, Y. and Wen, S. (2002b), "An analysis of elastohydrodynamic lubrication with limiting shear stress: part II - load influence", Trib. Trans., Vol. 45, pp. 211-6.
21. Zhang, Y. and Wen, S. (2002c), "EHL film thickness limitation theory under a limiting shear stress", Trib. Trans., Vol. 45, pp. 531-9.
22. Zhang, Y., Wen, S. and Wei, D.P. (2001), "About the load-carrying capacity of elastohydrodynamic lubrication film", Trib. Trans., Vol. 44, pp. 1-10.