About the load-carrying capacity of elastohydrodynamic lubrication film

Tribology Transactions

Volumn 44, Issue 1, 2001, Pages 1-10

  Yongbin, Zhang ^a   Shizhu, Wen ^a   Danping, Wei ^b  

^a TSINGHUA UNIVERSITY   (China)

^b RESEARCH INSTITUTE OF PETROLEUM PROCESSING   (China)

Author keywords

Elastohydrodynamic lubrication; Film loud carrying capacity; Lubricant viscoplasticity

Indexed keywords

EXTRAPOLATION; LOADS (FORCES); LUBRICANTS; SHEAR STRENGTH; SHEAR STRESS; SURFACES; TEMPERATURE; THIN FILMS; VISCOPLASTICITY;

ELASTOHYDRODYNAMIC LUBRICATION FILM; INLET ZONE SLIP; LOAD CARRYING CAPACITY; MAXIMUM HERTZIAN STRESSES; SURFACE SPEED;

ELASTOHYDRODYNAMIC LUBRICATION;

ELASTOHYDRODYNAMIC LUBRICATION; FILM; LOAD CAPACITY; SOLID LUBRICANT;

EID: 0035108727     PISSN: 10402004     EISSN: 1547397X     Source Type: Journal    
DOI: 10.1080/10402000108982419     Document Type: Article

References (37)

1. Czichos, H., “Failure Modes of Sliding Lubricated Concentrated Contacts,” Wear, 28. pp 95-101, (1974).
2. Lee, D., Sanborn, D. M. and Winer, W. O., “Some Observations of the Relationship Between Film Thickness and Load in High Hertz Pressure Sliding Elastohydrodynamic Contacts,” ASME Jour, of Lubr. Tech., 95. pp 386-390. (1973).
3. Parker, R. J and Kannel, J. W. NASA TND-6411. (1971).
4. Smeeth, M. and Spikes, H. A., “Central and Minimum Elastohydrodynamic Film Thickness at High Contact Pressure,” ASME Jour. of Trib., 119, pp 291-296, (1997).
5. Coy, J. J. and Zaretsky, E. V., “Some Limitations in Applying Classical EHD Film Thickncss Formulas to a High-Speed Bearing,” ASME Jour, of Lubr. Tech., 103. p 295. (1981).
6. Dyson, A. and Wilson, A. R., “Film Thickness in Elastohydrodynamic Lubrication by Silicone Fluids,” in Proc. Insin. Mech. Engrs., 180, Part 3K. p 119.(1965-1966).
7. Chang, L., Jackson, A and Webster, M. N., “Effects of 3-D Surface Topography on the EHL Film Thickncss and Film Breakdown,” Trib. Trans., 37. pp 435-444.
8. Patching, M. J., Kwch, C. C., Evans, H. P. and Sindle, R. W., “Conditions for Scuffing Failure of Ground and Superfinished Steel Disks at High Sliding Speeds Using a Gas Turbine Engine Oil,” ASME Jour. of Trib., 117. pp 482-489.
9. Cheng, H. S. and Stcrnlichl, B., “A Numerical Solution for the Pressure, Temperature, and Film Thickness Between Two Infinitely Long. Lubricated Rolling and Sliding Cylinders, Under Heavy Loads,” ASME Jour, of Basic Eng., pp 695-707. (1965).
10. Kim, K. H. and Sadeghi, F., “Non-Newtonian Elastohydrodynamic Lubrication of Point Contact,” ASME Jour. of Trib., 113, pp 703-711, (1991).
11. Paul, G. R. and Cameron, A., ”The Ultimate Shear Stress of Fluids at High Pressures Measured By a Modified Impact Microviscomoter,” in Proc. Roy. Soc. Lond., A. 365, pp 31-41, (1979).
12. Bair, S. and Winer, W. O., “The High Pressure High Shear Stress Rheology of Liquid Lubricants” ASME Jour. Of Trib., 114. p 1, (1992).
13. Evans, C. R. and Johnson, K. L., “The Rheological Properties of Khstohydrodynnmic Lubricants,” in Proc. Instn. Mech. Engrs, 200. pp 303-312,(1986).
14. Hoglund, E. and Jacobson, B., “Experimental Investigation of the Shear Strength of Lubricants Subjcctcd to High Pressure and Temperature,” ASME Jour. of Trib., 108, pp 571-578, (1986).
15. Jacobson, B. O. and Hnmrock B. J., “Non-Newtonian Fluid Model Incorporated Into Elastohydrodynamic Lubrication of Rectangular Contacts,” ASME Jour, of Trib., 106. pp 275-284, (1984).
16. Lee, R. T. and Hamrock, B. J., “A Circular Non-Newionian Fluid Model: Part I-Used in Elastohydrodynamic Lubrication,” ASME Jour. of Trib., 112, pp 486-495.(1990).
17. Smith, F. W., “Lubricant Behavior in Concentrated Contacts-Some Rheological Problems,” ASLE Trans., 3. pp 18-25. (1960).
18. Feng, R. and Ranicsh, K. T., “The Rheology of Lubricants at High Shear Rates,” ASME Jour. of Trib., 115. pp 640-649. (1993).
19. Bair, S. and Winer, W. O., “Shear Strength Measurements of Lubricants at High Pressure,” ASME Jour, of Lubr. Tech., 101, pp 251-257, (1979).
20. Bair, S. and Winer, W O., “The High Shear Stress Rheology of Liquid Lubricants at Pressures of 2 to 200 MPa,” ASME Jour. of Trib., 112, pp 246-253, (1990).
21. Jacobson, B. O., “On the Lubrication of Heavily Loaded Spherical Surfaces Considering Surfacc Deformations and Solidification of the Lubricant,” Acta Pofytechnica Scandinavica, Mech. Eng. Ser. No. 54. (1970).
22. Roclands, C. J. A., Vlutger, J. C. and Watermann H. I., “The Viscosity Temperature Pressure Relationship of Lubricating Oils and Its Correlation with Chemical Constitution” ASME Jour, of Basic Eng., p 601. (1963).
23. Dowson, D. and Higginson, G. R., Elastohydrodynamic Lubrication, The Fundamentals of Roller and Gear Lubrication, Pergamon Press. Ox ford. (1966).
24. Shizhu, W. and Yongbin, Z., “Elastohydrodynamics of the Lubricant with Limiting Shcax Stress; Part I-Algorithm and Solutions,” ASME Jour. of Trib (accepted). (1999)
25. Shizhu, W. and Peiran, Y., Elastohydrodynamic Lubrication (in Chinese). Tsinghua University Press. Beijing. (1990).
26. Johnson, K. L. and Roberts, A. D., “Film Thickncss Variation with Load in EHL Contacts” Wear, 27, pp 391-393, (1974).
27. Gentle, C. R. and Cameron, A., Letter to Nature, 246, pp 478-479. (1973).
28. Venner, C. H., “Multilevel Solution of the EHL Line and Point Contact Problems,” PhD Thesis, Twente University. Netherland. (1991).
29. Yongbin, Z. and Shizhu, W., “Film Thickness Limitation in Pure Rolling Line Contact EHL Due to the Lubricant Rheology,” ASME Jour. of Trib. (accepted), (2000).
30. Greenwood, J. A. and Kauzlarich, J. J., “Inlet Shear Heating in Elastohydrodynamic Lubrication,” ASME Jour. of Trib., pp 417-425. (1973).
31. Murch, L. E. and Wilson, W. R. D., “A Thermal Elastohydrodynamic Inlet Zone Analysis,” ASME Jour, of Lubr. Tech., pp 212-216, (1975).
32. Kannel, J. W. and Bell, J. C., “Interpretations of the Thickness of Lubricant Films in Rolling Contact: Part I-Examination of Measurements Obtained by X-Rays” ASME Jour, of Lubr. Tech., pp 478-484. (1971).
33. Cheng, H. S., “Isothermal Elastohydrodynamic Theory for the Full Range of Pressure-Viscosity Coefficient,” ASME Jour, of Lubr. Tech., pp 35-43, (1972).
34. Cheng, H. S., “Calculations of Elastohydrodynamic Film Thickness in High Speed Rolling and Sliding Contacts,” Mechanical Technology, Inc. Technical Report. MT1-67TR24. (1967).
35. Dowson, D. and Higginson, G. R., Elastohydrodynamic Lubrication, Pergamon Press. Oxford. (1977).
36. Johnson, K. L. and Tcvvarwerk, J. L., “Shear Behavior of Elastohydrodynamic Oil Films,” in Proc. Roy. Soc. Lond., Series A356, pp 215-236, (1977).
37. Shizhu, W. and Yongbin, Z., “Prevention of Film Slippage in Isothermal Pure Rolling Line Contact Elastohydrodynamic Lubrication Under Heavy Load,” Jour, of Mech. Eng. (in Chinese). 35. pp 81-89, (1999).