Numerical and experimental investigation of piston ring friction

Proceedings of the Spring Technical Conference of the ASME Internal Combustion Engine Division

Volumn , Issue , 2005, Pages 469-478

  Xu, H ^a   Bryant, M D ^a   Kim, M ^a   Matthews, R D ^a   Dardal, D ^a   Kiehne, T M ^a  

^a UNIVERSITY OF TEXAS   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

HYDRODYNAMIC LUBRICATION; PISTON RING FRICTION; VICINITY;

BOUNDARY CONDITIONS; FLOW OF FLUIDS; FRICTION; HYDRODYNAMICS; INTERNAL COMBUSTION ENGINES; LUBRICATION;

PISTON RINGS;

EID: 27744597932     PISSN: 15296598     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/ICES2005-1086     Document Type: Conference Paper

References (27)

1. Jeng, Y., 1992, "Friction and Lubrication Analysis of a Piston-Ring Pack," SAE Paper 920492.
2. Akalin, O., and Newaz, G.M., 2001, "Piston Ring-Cylinder Bore Friction Modeling in Mixed Lubrication Regime: Part I Analytical Results," ASME Journal of Tribology, 123, pp. 211-218.
3. Ting,L.L. and Mayer, J.E. Jr. 1974, "Piston Ring Lubrication and Cylinder Bore Wear Analysis, Part 1 - Theory," ASME Journal of Lubrication Technology, Vol. 96, pp 305-314.
4. Ting,L.L. and Mayer, J.E. Jr. 1974, "Piston Ring Lubrication and Cylinder Bore Wear Analysis, Part 2 - Theory Verification," ASME Journal of Lubrication Technology, Vol. 96, pp 258-266.
5. Dowson,D., 1993, "Piston Assemblies: Background and Lubrication Analysis," Engine Tribology, C.M. Taylor(Editor) Elsevier Science Publishers, B.V. pp. 213-240.
6. Namazian, M. and Heywood, J.B., 1982, "Flow in the Piston-Cylinder-Ring Crevices of a Spark-Ignition Engine: Effect on Hydrocarbon Emissions, Efficiency and Power," SAE Paper 820088.
7. Kuo,T., Sellnau, M.C. Theobald, M.A. and Jones, J.D., 1989, "Calculation of Flow in the Piston-Cylinder-Ring Crevices of a Homogeneous-Charge Engine and Comparison with Experiment," SAE Paper 890838.
8. Kim, C,G., Bae, C.S. and Choi, S.M., 2000, "Importance of Inter-Ring Crevice Volume as a Source of Unburned Hydrocarbon Emission - Numerical Considerations," Proc. Instn. Mech. Engrs., vol. 214, Part D. pp 395-403.
9. Keribar,R., Dursunkaya, Z. and Flemming, M.F., 1991, "An Integrated Model of Ring Pack Performance," ASME Journal of Engineering for Gas Turbines and Power, Vol. 113, pp 382-389.
10. Roberts, C.E. and Matthews, R.D.,1996, "Development and Application of an Improved Ring Pack Model for Hydrocarbon Emission Studies," SAE Paper 961966
11. Xu, H., Bryant. M.D., Matthews, R.D., Kiehne, T.M., Steenwyk. B.D., Bolander, N.W., and Sadeghi, F., 2004, "Friction Predictions for Piston Ring-Cylinder Liner Lubrication," Proceedings of ASME ICE 2004 Fall Technique Conference.
12. Rohde, S.M.,1980, "A Mixed Friction Model for Dynamically Loaded Contacts with Application to Piston Ring Lubrication," Surface Roughness Effects in Hydrodynamic and Mixed Lubrication, ASME Publication, pp. 19-50.
13. Dursunkaya, Z., Keribar, R., and Richardson, D.E., 1993, "Experimental and Numerical Investigation of Inter-Ring Gas Pressures and Blowby in a Diesel Engine," SAE Paper 930792
14. Tian,T, L. Noordzij. L.B, Wong, V.W, and Heywood, J.B.,1996, "Modeling Piston-Ring Dynamics, Blowby, and Ring-Twist Effects," ASME ICE-Vol. 27-3, 1996 Fall Technique Conference, Vol. 2, pp 67-80
15. Furuhama, S. and Hiruma, M., 1972, "Axial Movement of Piston Ring in the Groove," ASLE Trans, Vol. 15, pp 278-287.
16. Richardson, D.E., 1996, "Comparison of Measured and Theoretical Inter-Gas Pressure on a Diesel Engine," SAE Paper 961909
17. Furuhama, S., Hiruma, M. and Tsuzita, M., 1979, "Psiton Ring Motion and its Influence on Engine Tribology," SAE Paper 790860.
18. Wu, C.W. and Zhang, L.Q., 1989, "An Average Reynolds Equation for Partial Film Lubrication with Contact Factor," ASME Journal of Tribology, 111, pp. 188-191.
19. Tripp, J.H., 1983, "Surface Roughness Effects in Hydrodynamic Lubrication: The Flow Factor Method," ASME J. Lubrication Technology, 105, pp. 458-465.
20. Tonder, K., 1986, "The Lubrication of Unidirectional Striated Roughness: Consequences for Some General Roughness Theories," ASME J. Tribology, 108. pp. 167-170.
21. Peeken, H.J., and Knoll, G., 1997, "On the Numerical Determination of Flow Factors," ASME J. Tribology, 119, pp. 259-264.
22. Peklenik, J. 1967, "New Developments in Surface Characterization and Measurement by Means of Random Process Analysis," Proc. Insts. Mech.Engr. 182, Part 3K, pp. 108
23. Greenwood, J.A., and Tripp, J.H., 1971, "The Contact of Two Nominally Flat Rough Surfaces," Proc. Inst. Mech. Eng., 185, pp. 625-633.
24. Uras, H.M., and Patterson, D., 1983, "Measurement of Piston and Ring Assembly Friction by the Instantaneous IMEP Method," SAE Paper 830416.
25. Mufti, P., and Priest, M., and Chttenden, R., 2004, "Experimental and Theoretical Study of Instantaneous Piston Assembly Friction in a Gasoline Engine," TRIB2004-64199,ASME / STLE Tribology Conference.
26. Richardson, D.E., 2000, "Review of Power Cylinder Friction for Diesel Engines," ASME Journal of Engineering for Gas Turbines and Power, Vol. 122, pp 506-519.
27. Munson, B.R., Young, D.F., and Okiishi, T.H., 1994, "Fundamentals of Fluid Mechanics" John Wiley & Sons, Inc.