Friction predictions for piston ring-cylinder liner lubrication

Proceedings of the 2004 Fall Technical Conference of the ASME Internal Combustion Engine Division

Volumn , Issue , 2004, Pages 773-784

  Xu, H ^a   Bryant, M D ^a   Matthews, R D ^a   Kiehne, T M ^a   Steenwyk, B D ^b   Bolande, N W ^b   Sadeghi, F ^b  

^a UNIVERSITY OF TEXAS   (United States)

^b PURDUE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMBUSTION; ENGINE CYLINDERS; HYDRODYNAMICS; LUBRICANTS; LUBRICATION; PISTON RINGS; SURFACE ROUGHNESS; THIN FILMS; TRIBOLOGY;

HIGH-PRESSURE COMBUSTION GASES; LUBRICANT FLOW; MECHANICAL LOSSES; RING-LINER FRICTION; TRIBOLOGICAL MODELS;

FRICTION;

EID: 14044251512     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/icef2004-0885     Document Type: Conference Paper

References (19)

1. Patir, N., and Cheng, H.S., 1978, "An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication," ASME J. Lubrication Technology, 100, pp. 12-17.
2. Patir, N., and Cheng, H.S., 1979, "Application of Average Flow Model to Lubrication Between Rough Sliding Surfaces," ASME J. Lubrication Technology, 101, pp. 220-230.
3. Tripp, J.H., 1983, "Surface Roughness Effects in Hydrodynamic Lubrication: The Flow Factor Method," ASME J. Lubrication Technology, 105, pp. 458-465.
4. Tonder, K., 1986, "The Lubrication of Unidirectional Striated Roughness: Consequences for Some General Roughness Theories," ASME J. Tribology, 108, pp. 167-170.
5. Peeken, H.J., and Knoll, G., 1997, "On the Numerical Determination of Flow Factors," ASME J. Tribology, 119, pp. 259-264.
6. Makino, T., Morohoshi, S. and Saki, K., 1999, "The Effect of Roughness Orientation on Mixed Friction," Lubrication at the Frontier, D. Dowson et al., 35, pp. 355-365.
7. Rohde, S. M., Whitaker, K. W., and McAllister, G. T., 1980, "A Mixed Friction Model for Dynamically Loaded Contacts With Application to Piston Ring Lubrication," Surface Roughness Effects in Hydrodynamic and Mixed Lubrication, ASME Winter Annual Meeting, pp. 19-50.
8. Hu, Y., Cheng, H.S., Arai, T., Kobayashi, Y., and Aoyama, S., 1994, "Numerical Simulation of Piston Ring in Mixed Lubrication - A Non-Axisymmetrical Analysis," ASME J. Tribol., 116, pp. 470-478.
9. Akalin, O., and Newaz, G.M., 2001, "Piston Ring-Cylinder Bore Friction Modeling in Mixed Lubrication Regime: Part I - Analytical Results," ASME Journal of Tribology, 123, pp. 211-218.
10. Wu, C.W. and Zhang, L.Q., 1989, "An Average Reynolds Equation for Partial Film Lubrication with Contact Factor," ASME Journal of Tribology, 111, pp. 188-191.
11. Cheng, H.S, 2002, "Analytical Modeling of Mixed Lubrication Performance," Boundary and Mixed Lubrication: Science and Applications, D.Dowson et al., 34, pp. 19-33.
12. Peklenik, J. 1967, "New Developments in Surface Characterization and Measurement by Means of Random Process Analysis," Proc. Insts. Mech.Engr. 182, Part 3K, pp. 108
13. Bhushan, B., and Tonder, K., 1989, "Roughness-Induced Shear - and Squeeze-Film Effects in Magnetic Recording - Part 1: Analysis," ASME Journal of Tribology, 111, pp. 220-227.
14. Greenwood, J.A., and Tripp, J.H., 1971, "The Contact of Two Nominally Flat Rough Surfaces," Proc. Inst. Mech. Eng., 185, pp. 625-633.
15. Lo, S., 1992, "On the Effects of Roughness Orientation - A Mapping and Double Scale Analysis of Flow Factors," ASME Journal of Tribology, 114, pp. 747-754.
16. Payvar, P., and Salant, R.F., 1992, "A Computational Method for Cavitation in Wavy Mechanical Seal," ASME Journal of Tribology, 114, pp. 199-204.
17. Sawicki, J., and Yu, B., 2000, "Analytical Solution of Piston Ring Lubrication Using Mass Conserving Cavitation Algorithm," STLE Tribology Transactions, 43, pp. 587-594.
18. Jeng, Y., 1992, "Theoretical Analysis of Piston-Ring Lubrication Part 1-Fully Flooded Lubrication," STLE Tribology Trans., 35, pp. 696-706.
19. Patankar, S.V., 1980, Numerical Heat Transfer and Fluid Flow, Hemisphere Publishing Corp., Washington, D.C.