Deformation modelling in layered manufacturing of metallic parts using gas metal arc welding: Effect of process parameters

Modelling and Simulation in Materials Science and Engineering

Volumn 13, Issue 7, 2005, Pages 1187-1204

  Mughal, M P ^a   Fawad, H ^a   Mufti, R A ^a   Siddique, M ^a  

^a THE UNIVERSITY OF AGRICULTURE   (Pakistan)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; DEFORMATION; EDGE DETECTION; FINITE ELEMENT METHOD; GAS METAL ARC WELDING; PLATES (STRUCTURAL COMPONENTS); RESIDUAL STRESSES; THERMOANALYSIS;

HEAT SINK; PLATE EDGES; PROCESS PARAMETERS;

LAYERED MANUFACTURING;

EID: 25844460739     PISSN: 09650393     EISSN: None     Source Type: Journal    
DOI: 10.1088/0965-0393/13/7/013     Document Type: Article

References (19)

1. Zhang Y, Yiwei P, Chen Y and Male A 2002 Automated system for welding based rapid prototyping Mechatronics 12 37-53
2. Dipl-Ing Merz R 1994 Shape deposition manufacturing PhD Dissertation eingereicht an der Technischen Universitat, Wien
3. Spencer J, Dickens P and Wykes C 1998 Rapid prototyping of metal parts by 3D welding J. Eng. Manuf. Proc. Inst. Mech. Eng. B 212 175-81
4. Jayanthi S, Keefe M and Gargiulo E 1994 Studies in stereolithography: influence of process parameters on curl distortion in photopolymer models Proc. Solid Freeform Fabrication Symposium (Austin, Texas, 1994) pp 250-8
5. Ullett J, Chartoff R, Lightman A, Murphy J and Li J 1994 Reducing warpage in stereolithography through novel draw styles Proc. Solid Freeform Fabrication Symposium (Austin, Texas, 1994) pp 242-9
6. Jacobs P 1996 Rapid Prototyping and Manufacturing: Fundamentals of Stereolithography (Dearborne, Michigan: Society of Manufacturing Engineers)
7. Karapatis N, Guidoux Y, Gygax P and Glardon R 1998 Thermal behavior of parts made by direct metal laser sintering Proc. Solid Freeform Fabrication Symposium (Austin, Texas, 1998) pp 79-87
8. Dickens P, Cobb R, Gibson I and Pridham M 1993 Rapid prototyping using 3D welding J. Des. Manuf. 1 39-44
9. Nickel A 1999 Analysis of thermal stresses in shape deposition manufacturing of metal parts PhD Thesis Stanford University
10. Nickel A, Barnett D and Prinz F 2001 Thermal stresses and deposition patterns in layered manufacturing Mater. Sci. Eng. A 317 59-64
11. Klingbeil N, Beuth J, Chin R and Amon C 2002 Residual stress-induced warping in direct metal solid freeform fabrication Int. J. Mech. Sci. 44 57-77
12. Fawad H, Mughal P and Siddique M 2004 Finite element simulation of welding based deposition process as applied to layered manufacturing: thermal model, IMECE2004: Int. Mechanical Engineering Conf. and Exhibition 2004 pp 656-73 IMEC04-5062
13. Lindgren L 2001 Finite element modeling and simulation of welding part 1: increased complexity J. Therm. Stresses 24 141-92
14. Goldak J, Bibby M, Moore J, House R and Patel B 1986 Computer modeling of heat flow in welds Metall. Trans. B 15 587-600
15. Kamala V and Goldak J A 1993 Error due to two dimensional approximation in heat transfer analysis of welds Weld. J. 72 440s-6s
16. Karlson R and Josefson B 1990 Three dimensional finite element analysis of temperature and stresses in a single pass butt-welded pipe ASME Trans. 112 76-83
17. Abid M, Siddique M and Mufti R 2005 Prediction of welding distortions and residual stresses in a pipe-flange joint using the finite element technique Modelling Simul. Mater. Sci. Eng. 13 455-70
18. Lindgren L 2001 Finite element modeling and simulation of welding part 2: improved material modeling J. Therm. Stresses 24 195-231
19. Masubuchi K 1980 Analysis of Welded Structures (International series on Materials Science and Technology) vol 33 1st edn (New York: Pergamon Press)