Optimal design of slider shape for satisfying load demands under specified operation conditions

Tribology International

Volumn 38, Issue 8, 2005, Pages 757-768

  Chang, Mei Hsia ^a   Cheng, Chin Hsiang ^a  

^a TATUNG UNIVERSITY   (Taiwan)

Author keywords

Conjugate gradient method; Inverse method; Shape design; Slider

Indexed keywords

COMPRESSIBLE FLOW; FORCE MEASUREMENT; MACHINE DESIGN; MATHEMATICAL MODELS; OPTIMIZATION; PRESSURE DISTRIBUTION; PROBLEM SOLVING; STRUCTURAL LOADS; VECTORS; VISCOSITY;

CONJUGATE GRADIENT METHODS; INVERSE METHODS; SHAPE DESIGN; SLIDERS;

BEARINGS (MACHINE PARTS);

EID: 18444374715     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2004.11.005     Document Type: Article

References (17)

1. R.O. Boswall The Michell thrust bearing Engineering 120 1925 153 155
2. M. Muskat, F. Morgan, and M.W. Meres The lubrication of plane sliders of finite width J Appl Phys 11 1940 208 219
3. K. Kogure, S. Fukui, Y. Mitsuya, and R. Kaneko Design of negative pressure slider for magnetric recording disks J Lubric Technol 105 1983 496 502
4. R.H. Buckholz Effects of power-law, non-newtonian lubricants on load capacity and frication for plane slider bearings ASME J Tribol 108 1986 86 91
5. J.P. Peng, and C.E. Hardie A finite element scheme for determining the shaped rail slider flying characteristics with experimental confirmation ASME J Tribol 117 1995 136 142
6. L. Wu, and D.B. Bogy Unstructured triangular mesh generation techniques and a finite volume numerical scheme for slider air bearing simulation with complex shaped rails IEEE Trans Magn 35 1999 2421 2423
7. H. Hashimoto, and Y. Hattori Improvement of the static and dynamic characteristics of magnetic head sliders by optimum design ASME J Tribol 122 2000 280 287
8. H. Kotera, and S. Shima Shape optimization to perform prescribed air lubrication using genetic algorithm Tribol Trans 43 2000 837 841
9. H. Zhu, and D.B. Bogy Hard disc drive air bearing design: modified DIRECT algorithm and its application to slider air bearing surface optimization Tribol Int 37 2004 193 201
10. C.H. Cheng, and M.H. Chang Shape design for surface of a slider by inverse method J Tribol 126 2004 519 526
11. M. Hanke Conjugate gradient type methods for ill-posed problems 1995 Wiley New York
12. W.A. Gross, L.A. Matsch, V. Castelli, A. Eshel, J.H. Vohr, and M. Wildmann Film thin lubrication 1980 Wiley New York p. 188-190
13. Y. Mitsuya, and S. Fukui Stokes roughness effects on hydrodynamic lubrication. Part 1 - comparison between incompressible and compressible lubricating films ASME J Tribol 108 1986 151 158
14. C.H. Cheng, and C.Y. Wu An approach combining body-fitted grid generation and conjugate gradient methods for shape design in heat conduction problems Numerical Heat Transfer, Part B 37 2000 69 83
15. C.H. Cheng, and M.H. Chang Shape design for a cylinder with uniform temperature distribution on the outer surface by inverse heat transfer method Int J Heat Mass Transfer 46 2003 101 111
16. C.H. Cheng, and M.H. Chang Shape identification by inverse heat transfer method J Heat Transfer 125 2003 224 231
17. S. Fukui, and R. Kaneko Analysis of ultra-thin gas film lubrication based on linearized Boltzmann equation: first report-derivation of a generalized lubrication equation including thermal creep flow ASME J Tribol 110 1988 253 262