Shape design for surface of a slider by inverse method

Journal of Tribology

Volumn 126, Issue 3, 2004, Pages 519-526

  Cheng, Chin Hsiang ^a   Chang, Mei Hsia ^a  

^a TATUNG UNIVERSITY   (Taiwan)

Author keywords

Conjugate gradient method; Inverse method; Shape design; Slider

Indexed keywords

GEOMETRY; INVERSE KINEMATICS; PRESS LOAD CONTROL; PRESSURE CONTROL; SURFACES;

LOAD DEMANDS; SLIDER;

ROTORS;

DESIGN; FLUID FILM; PRESSURE DISTRIBUTION; SHAPE; SLIDING BEARING;

EID: 3543032795     PISSN: 07424787     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1704627     Document Type: Article

References (17)

1. White, J. W., 1983, "Flying Chrarcteristics of the 'Zero-Load' Slider Bearing," ASME J. Lubr. Technol., 105, pp. 484-490.
2. Buckholz, R. H., 1986, "Effects of Power-Law, Non-Newtonian Lubricants on Load Capacity and Friction for Plane Slider Bearings," ASME J. Tribol., 108, pp. 86-91.
3. Kubo, M., Ohtsubo, Y., Kawashima, N., and Marumo, H., 1988, "Finite Element Solution for the Rarefied Gas Lubrication Problem," ASME J. Tribol., 110, pp. 335-341.
4. Hu, Y., and Bogy, D. B., 1997, "Dynamic Stability and Spacing Modulation of Sub-25 nm Fly Height Sliders," ASME J. Tribol., 119, pp. 646-652.
5. Wang, N., Ho, C. L., and Cha, K. C., 2000, "Engineering Optimum Design of Fluid-Film Lubricated Bearings," Tribol. Trans., 43, pp. 377-386.
6. Hu, Y., 1999, "Contact Take-Off Characteristics of Proximity Recording Air Bearing Sliders in Magnetic Hard Disk Drivers," ASME J. Tribol., 121, pp. 948-954.
7. Hashimoto, H., and Hattori, Y., 2000, "Improvement of the Static and Dynamic Characteristics of Magnetic Head Sliders by Optimum Design," ASME J. Tribol., 122, pp. 280-287.
8. Yoon, S. J., and Choi, D. H., 1997, "An Optimum Design of the Transverse Pressure Contour Slider for Enhanced Flying Characteristics," ASME J. Tribol., 119, pp. 520-524.
9. Kotera, H., and Shima, S., 2000, "Shape Optimization to Perform Prescribed Air Lubrication Using Genetic Algorithm," Tribol. Trans., 43, pp. 837-841.
10. El-Gamal, H. A., and Awad, T. H., 1994, "Optimum Model Shape of Sliding Bearings for Oscillating Motion," Tribol. Int., 27, pp. 189-196.
11. O'Hara, M. A., Hu, Y., and Bogy, D. B., 2000, "Optimization of Proximity Recording Air Bearing Sliders in Magnetic Hard Disk Drivers," ASME J. Tribol., 122, pp. 257-259.
12. Kang, T. S., Choi, D. H., and Jeong, T. G., 2001, "Optimal Design of HDD Air-Lubricated Slider Bearings for Improving Dynamic Characteristics and Operating Performance," ASME J. Tribol., 123, pp. 541-547.
13. Hanke, M., 1995, Conjugate Gradient Type Methods for III-Posed Problems, John Wiley & Sons, New York.
14. Cheng, C. H., and Wu, C. Y., 2000, "An Approach Combining Body-Fitted Grid Generation and Conjugate Gradient Methods for Shape Design in Heat Conduction Problems," Numer. Heat Transfer, Part B, 37, pp. 69-83.
15. Cheng, C. H., and Chang, M. H., 2003, "Shape Design for a Cylinder With Uniform Temperature Distribution on the Outer Surface by Inverse Heat Transfer Method," Int. J. Heat Mass Transfer, 46, pp. 101-111.
16. Cheng, C. H., and Chang, M. H., 2003, "Shape Identification by Inverse Heat Transfer Method," ASME J. Heat Transfer, 125, pp. 224-231.
17. Gross, W. A., Matsch, L. A., Castelli, V., Eshel, A., Vohr, J. H., and Wildmann, M., 1980, Fluid Film Lubrication, John Wiley & Sons, New