Local heat/mass transfer with various rib arrangements in impingement/effusion cooling system with crossflow

Journal of Turbomachinery

Volumn 126, Issue 4, 2004, Pages 615-626

  Rhee, Dong Ho ^a   Nam, Yong Woo ^a   Cho, Hyung Hee ^a  

^a Yonsei University   (South Korea)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; HEAT TRANSFER; INSTALLATION; JETS; PERFORATORS; PLATE METAL; PRESSURE DROP; REYNOLDS NUMBER;

CROSSFLOW; EFFUSION COOLING; IMPINGEMENT; PERFORATED PLATES;

MASS TRANSFER;

CROSSFLOW; HEAT TRANSFER; MASS TRANSFER; WALL JET;

EID: 14744302081     PISSN: 0889504X     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1791287     Document Type: Article

References (32)

1. Hollwarth, B. R., and Dagan, L., 1980, "Arrays of Impinging Jets with Spent Fluid Removal Through Vent Holes on the Target Surface. Part 1: Average Heat Transfer," J. Eng. Power, 102, pp. 994-999.
2. Hollwarth, B. R., and Lehmann, G., and Rosiczkowski, J., 1983, "Arrays of Impinging Jets with Spent Fluid Removal through Vent Holes on the Target Surface. Part 2: Local Heat Transfer," J. Eng. Power, 105, pp. 393-402.
3. Nazari, A., and Andrews, G. E., 1999, "Impingement/Effusion Cooling: Influence of Number of the Holes and Pressure Loss on Film and Heat Transfer Coefficient," Proc. 7th IGTC, 2, 1999, pp. 638-648.
4. Cho, H. H., and Goldstein, R. J., 1996, "Effect of Hole Arrangements on Impingement/Effusion Cooling," Proc. 3rd KSME-JSME Thermal Engineering Conf., pp. 71-76.
5. Cho, H. H., and Rhee, D. H., 2001, "Local Heat/Mass Transfer Measurement on the Effusion Plate in Impingement/Effusion Cooling System," J. Turbomach., 123, pp. 601-608.
6. Rhee, D. H., Choi, D. H., and Cho, H. H., 2003, "Heat (Mass) transfer on Effusion Plate in Impingement/Effusion Cooling Systems," J. Thermophys. Heat Transfer, 17, No. 1, pp. 95-102.
7. Metzger, D. E., and Korstad, R. J., 1992, "Effects of Crossflow in Impingement Heat Transfer," J. Eng. Power, 94, pp. 35-41.
8. Behbahani, A. I., and Goldstein, R. J., 1983, "Local Heat Transfer to Staggered Arrays of Impinging Circular Air Jets," J. Eng. Power, 105, pp. 354-360.
9. Florschuetz, L. W., Metzger, D. E., and Su, C. C., 1984, "Heat Transfer Characteristics for Jet Array Impingement With Initial Crossflow," J. Heat Transfer, 106, pp. 34-41.
10. Haiping, C., Wanbing, C., and Taiping, H., 1999, "3-D Numerical Simulation of Impinging Jet Cooling with Initial Crossflow," ASME paper no. 99-GT-256.
11. Rhee, D. H., Yoon, P. H., and Cho, H. H., 2003, "Local Heat/Mass Transfer and Flow Characteristics of Array Impinging Jets with Effusion Holes Ejecting Spent Air," Int. J. Heat Mass Transfer, 46, pp. 1049-1061.
12. Bailey, J. C., and Bunker, R. S., 2002, "Local Heat Transfer and Flow Distributions for Impinging Jet Arrays of Dense and Sparse Extent," ASME paper no. GT-2002-30473.
13. Gao, L., Ekkad, S. V., and Bunker, R. S., 2003, "Impingement Heat Transfer Under Linearly Stretched Arrays of Holes," ASME paper no. GT-2003-38178.
14. Rhee, D. H., Choi, J. H., and Cho, H. H., 2003, "Flow and Heat (Mass) Transfer Characteristics in an Impingement/Effusion Cooling System with Crossflow," J. Turbomach., 125, pp. 74-82.
15. Haiping, C., Dalin, Z., and Taiping, H., 1997, "Impingement Heat Transfer from Rib Roughened Surface within Arrays of Circular Jets: The Effects of the Relative Position of the Jet Hole to the Ribs," ASME paper no. 97-GT-331.
16. Haiping, C., Jingyu, Z., and Taiping, H., 1998, "Experimental Investigation on Impingement Heat Transfer from Rib Roughened Surface within Arrays of Circular Jets: Effect of Geometric Parameters," ASME paper no. 98-GT-208.
17. Andrews, G. E., Abdul Hussain, R. A. A., and Mkpadi, M. C., 2003, "Enhanced Impingement Heat Transfer: Comparison of Co-flow and Cross-flow with Rib Turbulators," Proc. IGTC2003, Paper No. IGTC2003 Tokyo TS-075.
18. Cho, H. H., and Goldstein, R. J., 1995, "Heat (Mass) Transfer and Film Cooling Effectiveness with Injection through Discrete Holes-Part I: Within Holes and on the Back Surface," J. Turbomach., 117, pp. 440-450.
19. Cho, H. H., Wu, S. J., and Kwon, H. J., 2000, "Local Heat/Mass Transfer Measurements in a Rectangular Duct with Discrete Ribs," ASME J. Turbomach., 122, pp. 579-586.
20. Han, J. C., Chandra, P. R., and Lau, S. C., 1988, "Local Heat/Mass Transfer Distributions around 180 deg. Turns in Two-pass Smooth and Rib-Roughened Channels," J. Heat Transfer, 110, pp. 91-98.
21. Chandra, P. R., Han, J. C., and Lau, S. C., 1988, "Effect of Rib Angle on Local Heat/Mass Transfer Distribution in a Two-pass Rib-Roughened Channel," J. Turbomach., 110, pp. 233-241.
22. Ekkad, S. K., and Han, J. C., 1997, "Detailed Heat Transfer Distributions in Two-pass Square Channels with Rib Turbulators," Int. J. Heat Mass Transfer, 40, No. 11, pp. 2525-2537.
23. Liou, T. M., and Hwang, J. J., 1993, "Effect of Ridge Shapes on Turbulent Heat Transfer and Friction in a Rectangular Channel," Int. J. Heat Mass Transfer, 36, No. 4, pp. 931-940.
24. Goldstein, R. J., and Cho, H. H., 1995, "A Review of Mass Transfer Measurement Using Naphthalene Sublimation," Exp. Therm. Fluid Sci., 10, pp. 416-434.
25. Eckert, E. R. G., Analogies to Heat Transfer Processes, in Measurements in Heat Transfer, edited by Eckert, E. R. G., and Goldstein, R. J., 1976, pp. 397-423, Hemisphere Pub., New York.
26. Kline, S. J., and McClintock, F., 1953, "Describing Uncertainty in Single Sample Experiments," Mech. Eng. (Am. Soc. Mech. Eng.), 75, pp. 3-8.
27. Fluent 6.1 User's Guide Volume 2 (Chaps. 8-19), 2003.
28. Dittus, P. W., and Boelter, L. M. K., 1930, Univ. Calif. Publ. Eng., 2, No. 13, pp. 443-461; reprinted in 1985 Int. Commun. Heat Mass Transfer, 12, pp. 3-22.
29. Chandra, P. R., Niland, M. E., and Han, J. C., 1995, "Turbulent Flow Heat Transfer and Friction in a Rectangular Channel with Varying Number of Ribbed Walls," ASME J. Turbomach., 119, pp. 374-380.
30. Cavellero, D., and Tanda, G., 2002, "An Experimental Investigation of Forced Convection Heat Transfer in Channels with Rib Turbulators by means of Liquid Crystal Thermography," Exp. Therm. Fluid Sci., 26, pp. 115-121.
31. Hermanson, K., Parneix, S., Von Wolfersdorf, J., and Semmler, K., 2001, "Prediction of Pressure Loss and Heat Transfer in Internal Cooling Passages," Heat Transfer in Gas Turbine Systems, Annals of the New York Academy of Sciences, 932, pp. 448-455.
32. Hermanson, K., Kern, S., Picker, G., and Parneix, S., 2003, "Predictions of External Heat Transfer for Turbine Vanes and Blades With Secondary Flowfields," J. Turbomach., 125, pp. 107-113.