A new method for roundness control in taper turning using fcc techniques

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 123, Issue 4, 2001, Pages 567-575

  Fung, Eric H K ^a   Yang, S M ^a  

^a HONG KONG POLYTECHNIC UNIVERSITY   (Hong Kong)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 13544269817     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.1372196     Document Type: Article

References (27)

1. Wu, S. M., 1977, “Dynamic Data Systems: A New Modeling Approach,” ASME J. Eng. Ind., 99, pp. 708-714.
2. Moon, E. J., Eman, K. F., and Wu, S. M. 1984, “Implementation of Forecasting Compensatory Control for Machining Straightness,” ASME Winter Annual Meeting, pp. 47-53.
3. Rao, S. B., and Wu, S. M., 1982, “Compensatory Control of Roundness Error in Cylindrical Chuck Grinding,” ASME J. Eng. Ind., 104, pp. 385-391.
4. Rao, S. B., and Wu, S. M., 1982, “A Quantitative Analysis of Roundness Error in Cylindrical Chunk Grinding” Int. J. Mach. Tool Des. Res., 21, pp. 41-48.
5. Kim, K. H., Eman, K. F., and Wu, S. M., 1985, “Forecasting Compensatory Control of Spindle Error Motion in Cylindrical Grinding,” ASME Statistics in Manufacturing, PED-Vol. 9, pp. 75-81.
6. Kim, K. H., Eman, K. F., and Wu, S. M., 1987, “Development of a Forecasting Compensatory Control System for Cylindrical Grinding,” ASME J. Eng. Ind., 109, pp. 385-391.
7. Huang, K., and Wu, S. M., 1984, “Forecasting Compensatory Control (FCC) of Roundness in Boring,” International Computers in Engineering Conference and Exhibit, Las Vegas, Nevada, pp. 378-383.
8. Kim, K. H., Eman, K. F., and Wu, S. M., 1987, “In-Process Control of Cylindricity in Boring Operations,” ASME J. Eng. Ind., 109, pp. 291-296.
9. Your, S. B., 1987, “Precision Control on the Flatness of Winchester Disc in Face-Turning Operations,” Ph.D. Dissertation, University of Wisconsin-Madison.
10. Fung, E. H. K., Cheung, S. M., and Leung, T. P., 1998, “Implementation of an Error Forecasting and Compensation System for Roundness Improvement in Taper Turning,” Computers in Industry, 35, pp. 109-20.
11. Xu, W. L., and Han, L., 1999, “Piezoelectric Actuator Based Active Error Compensation of Precision Machining,” Meas. Sci. Technol., 10, pp. 106-111.
12. Wu, S. M., and Ni, J., 1988, “New Approaches to Achieve Better Machine Performance,” Proceedings of the USA-Japan Symposium on Flexible Automation, Vol. 2, pp. 1063-1068.
13. Wu, S. M., and Ni, J., 1989, “Precision Machine without Precise Machinery,” CIRP Ann., 38, pp. 533-536.
14. Uda, Y., Kohno, T., and Yazawa, T., 1996, “In-process Measurement and Workpiece-referred Form Accuracy Control System (WORFAC): Application to Cylindrical Turning Using an Ordinary Lathe,” Journal of the American Society for Precision Engineering, 18, pp. 50-55.
15. Li, C. J., and Li, S. Y., 1992, “On-line Roundness Error Compensation via P-Integrator Learning Control,” ASME J. Eng. Ind., 114, pp. 476-480.
16. Li, S. Y., and Li, C. J., 1994, “Cylindricity Error Compensation in Diamond Turning via P-Integrator Repetitive Control,” Tran. NAMRI/SME, 22, pp. 79-84.
17. Hanson, R. D., and Tsao, T.-C., 1998, “Reducing Cutting Force Induced Bore Cylindricity Errors by Learning Control and Variable Depth of Cut Machining,” ASME J. Manuf. Sci. Eng., 120, pp. 547-554.
18. Whitehouse, D. J., 1976, “Some Theoretical Aspects of Error Separation Techniques in Surface Metrology,” J. Phys. E, 9, pp. 531-536.
19. Zhang, G. X., Zhang, Y. H., Yang, S. M., and Li, Z., 1997, “A Multipoint Method for Spindle Error Motion Measurement,” CIRP Ann., 46, pp. 441-445.
20. Tong, S., 1996, “Two-step Method Without Harmonics Suppression in Error Separation,” Meas. Sci. Technol., 7, pp. 1563-1568.
21. Zhang, G. X., and Wang, R. K., 1993, “Four-Point Method of Roundness and Spindle Error Measurements,” CIRP Ann., 42, pp. 593-596.
22. Kato, H., Nikura, M., and Nakano, Y., 1991, “Minute Control of Rotational Error Motion of Workpiece by Using Piezo-Actuator in Precision Cylindrical Grinding,” Int. J. Jpn. Soc. Precis. Eng., 25, pp. 303-308.
23. Schrama, P. R. J., and Franse, J., 1988, “The Precision Cutting Process as a Non-linear Closed Loop System,” Precis. Eng., 10, pp. 199-207.
24. Fassois, S. D., Eman, K. F., and Wu, S. M., 1989, “A Fast Algorithm for On-line Machining Process Modeling and Adaptive Control,” ASME J. Eng. Ind., 111, pp. 133-139.
25. Teja, S. R., and Jayasingh, T., 1993, “Characterization of Ground Surface Profiles-A Comparison of AR, MA, ARMA Modeling Approach,” Int. J. Mach. Tools Manuf., 33, No. 1, pp. 103-109.
26. Fung, E. H. K., and Chung, A. P. L., 1999, “Using ARMA Models to Forecast Workpiece Roundness Error in a Turning Operation,” Appl. Math. Model., 23, pp. 567-585.
27. Bennis, S., and Assaf, G. J., 1994, “Adaptive Forecast of Multi-month Lake Level Elevation,” Can. J. Civ. Eng., 21, pp. 778-788.