MEMS Enabled Micro Spray Cooling System for Thermal Control of Electronic Chips

American Society of Mechanical Engineers, Heat Transfer Division, (Publication) HTD

Volumn 369, Issue 7, 2001, Pages 181-192

  Yao, S C ^a   Amon, C H ^a   Gabriel, K ^a   Kumta, P ^a   Murthy, J Y ^a   Wu, C F ^a   Hsieh, C C ^a   Boyalakuntla, D ^a   Narumanchi, S V J ^a   Rebello, K ^a  

^a CARNEGIE MELLON UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

MICRO SPRAY COOLING; THERMAL CONTROL;

COOLING; EVAPORATION; HEAT FLUX; HEAT TRANSFER; MATHEMATICAL MODELS; MICROELECTROMECHANICAL DEVICES; MICROPROCESSOR CHIPS; SWIRLING FLOW;

ELECTRONIC EQUIPMENT;

EID: 12144290397     PISSN: 02725673     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (28)

1. Amon, C.H., 1993, "Spectral element-Fourier method for transitional flows in complex geometries," AIAA Journal, Vol. 31, No. 1, pp. 42-48.
2. Amon, C.H., 1995, "Spectral element-Fourier method for unsteady conjugate heat transfer in complex geometry flows," AIAA Journal of ThermoPhysics and Heat Transfer, Vol. 9, No. 2, pp. 247-253.
3. Amon, C.H., Murthy, J.Y., Yao, S.C., Narumanchi, S., Wu, C.F. and Hsieh, C.C., in press 2001, "MEMS-Enabled Thermal Mangement of High-Heat-Flux Devices, EDIFICE: Embedded Droplet Impingement for Integrated Cooling of Electronics," Experimental Thermal and Fluid Science Journal.
4. Bergles, A.E. and Kim, C-J., 1988, "A method to reduce temperature overshoots in immersion cooling of electronic devices," InterSociety Conference on Thermal Phenomena in Fabrication and Operation of Electronic Components, IEEE, New York, pp. 100-105.
5. Bergles, A.E. and Bar-Cohen, A., 1990, "Direct cooling of microelectronic components," Advanced Thermal Modeling of Electronic Components and Systems, Eds. Bar-Cohen, A. and Kraus, A.D., ASME Press, New York, Vol. 2, pp. 233-250.
6. Bhavnani, S.H., Tsai, C.P., Jaeger, R.C. and Eison, D.L., 1993, "An integral heat sink for cooling microelectronic components," ASME Journal of Electronic Packaging, Vol. 115, pp. 284-291.
7. Carvalho, R.D.M., and Bergles, A.E., 1990, "The influence of sub-cooling on the pool nucleate boiling and critical heat flux of simulated electronic chips," Ninth International Heat Transfer Conference, Hemisphere, New York, pp. 289-294.
8. Copeland, D., 1998, "Single-phase and boiling cooling of a small heat source by multiple nozzle jet impingement," International Journal of Heat and Mass Transfer, Vol. 39, No. 7, pp. 1395-1406.
9. Incropera, F.P., Wolf, D.H., and Viskanta, R., 1996, "Local jet impingement boiling heat transfer," International Journal of Heat and Mass Transfer, Vol. 39, No. 7, pp. 1395-1406.
10. Jain, A., Boyalakuntla, D., Murthy, J.Y. and Amon C.H., 2001, "Buoyancy driven flow in channels with in-line pin fins," ASME National Heat Transfer Conference. Anaheim, CA, NHTC2001-20017.
11. Karki, K. C. and Patankar, S. V., 1987, "Cooling of a vertical shrouded fin array by natural convection: a numerical study," Journal of Heat Transfer, Vol. 109, pp. 671-676.
12. Miller, W.J., 1991, "Boiling and visualization for microconfigured surfaces," M.S. Thesis, University of Pennsylvania, Philadelphia, PA.
13. Mudawar, I., and Estes, K.A., 1995, "Comparison of two-phase electronic cooling using free jets and sprays," Advances in Electronic Packaging, Proceedings of International Electronic Packaging Conference, Vol. 2, pp. 975-987.
14. Nakayama, W., Daikoku, T., Kuwahara, H. and Nakajima, T., 1980, "Dynamic model of enhancement boiling heat transfer on porous surfaces, part I: Experiemental investigation," Journal of Heat Transfer, Vol. 102, pp. 445-450.
15. Nakayama, W., Nakajima, T. and Hirasawa, S., 1984, "Heat sink studs having enhanced boiling surfaces for cooling microelectronic components," ASME84-WA/HT-89.
16. Nakayama, W., and Copeland, D., 1994, "Heat transfer from chips to dielectric coolant: enhanced pool boiling versus jet impingement cooling," Enhanced Heat Transfer, Vol. 1, No. 3, pp. 231-243.
17. th ASME National Heat Transfer Conference, Paper No. NHTC2000-12138.
18. Narumanchi, S.V.J., Amon, C.H., and Murthy, J.Y., 2001, "Impact of pulsating submerged liquid jets on chip-level thermal phenomena," submitted to ASME Journal of Electronic Packaging.
19. st National Heat Transfer Conference, ASME HTD, Vol. 329, No. 7, pp. 97-108.
20. Park, K.A. and Bergles, A.E., 1986, "Boiling heat transfer characteristics of simulated microelectronic chips with detachable heat sinks," Eighth International Heat Transfer Conference, Hemisphere Publishing Corporation, Washington, DC, Vol. 4, pp. 299-2104.
21. Patera, A.T., 1984, "A spectral element method for fluid dynamics: Laminar flow in a channel expansion," Journal of Computational Physics, Vol. 54, pp. 468-488.
22. Patankar, S.V., 1980, Numerical Heat Transfer and Fluid Flow. Hemisphere.
23. Peterson, G.P., 1994, An Introduction to Heat Pipes. John Wiley and Sons, Inc., New York.
24. Ravigururajan, T.S., and Bergels, A.E., 1994, "Visualization of flow phenomena near enhanced surfaces," Journal of Heat Transfer, Vol. 116, pp. 54-57.
25. Reid, R.S., Pate, M.B. and Bergles, A.E., 1991, "A comparison of augmentation techniques during in-tube evaporation of R-113," Journal of Heat Transfer, Vol. 113, pp. 451-458.
26. Rhie, C.M. and Chow, W.L., 1983, "A numerical study of the turbulent flow past an isolated airfoil with trailing edge separation," AIAA J., Vol. 21, pp. 1525-1532.
27. th International Conference on Multiphase Flow.
28. Yao, S.C., Deb, S., and Hammouda, N., 1989, "Impact spray boiling for thermal control of electronic systems," ASME HTD-Heat Transfer in Electronics, Vol. 111, pp. 129-133.