Genetic tool monitor (GTM) for micro-end-milling operations

International Journal of Machine Tools and Manufacture

Volumn 45, Issue 3, 2005, Pages 293-299

  Tansel, I N ^a   Bao, W Y ^a   Reen, N S ^a   Kropas Hughes, C V ^b  

^a The Department of Electrical and Computer Engineering   (United States)

^b AIR FORCE RESEARCH LABORATORY   (United States)

Author keywords

End milling; Genetic algorithms; Manufacturing applications; Micro machining; Process monitoring

Indexed keywords

END-MILLING OPERATIONS; GENETIC TOOL MONITOR (GTM); MANUFACTURING APPLICATIONS; PROCESS MONITORING;

COMPUTER SIMULATION; CUTTING; DYNAMOMETERS; FUZZY SETS; GENETIC ALGORITHMS; MATHEMATICAL MODELS; MICROMACHINING; MILLING (MACHINING); MONITORING; OPERATIONS RESEARCH; SAMPLING; SENSORS; TIME SERIES ANALYSIS; WEAR OF MATERIALS;

TOOLS;

EID: 10444271769     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijmachtools.2004.08.013     Document Type: Article

References (15)

1. D.E. Goldberg Genetic Algorithms in Search, Optimization and Machine Learning 1989 Addison-Wesley Reading, MA
2. J.H. Holland Adaptation in Natural and Artificial Systems, A Bradford Book 1992 The MIT Press Cambridge, MA
3. D.L. Carroll Chemical laser modeling with genetic algorithms AIAA Journal 34 2 1996 338 346
4. I. Tansel, W.Y. Bao, B. Tansel, R. Shisler, D. Smith, J. Murray, Identification of cutting conditions by using an analytical model and genetics algorithms for micro-end-milling operations, Intelligent Engineering Systems through Artificial Neural Networks 8 (1998) 779-784.
5. I.N. Tansel, W.Y. Bao, T.T. Arkan, and C.V. Kropas-Hughes Genetic algorithm versus neural network in health monitoring applications Intelligent Engineering Systems Through Artificial Neural Networks 12 2002 255 260
6. W.Y. Bao, and I.N. Tansel Modeling micro-end-milling operations. Part I. Analytical cutting force model International Journal of Machine Tools Manufacture 40 15 2000 2155 2173
7. W.Y. Bao, and I.N. Tansel Modeling micro-end-milling operations. Part II. Tool run-out International Journal of Machine Tools and Manufacture 40 15 2000 2175 2192
8. W.Y. Bao, and I.N. Tansel Modeling micro-end-milling operations. Part III. Influence of tool wear International Journal of Machine Tools and Manufacture 40 15 2000 2193 2211
9. F. Cus, and J. Balic Optimization of cutting process by GA approach Robotics and Computer-Integrated Manufacturing 19 1-2 2003 113 121
10. J.P. Davim, and C.A.C. António Optimisation of cutting conditions in machining of aluminium matrix composites using a numerical and experimental model Journal of Materials Processing Technology 112 1 2001 78 82
11. M.S. Shunmugam, S.V. Bhaskara Reddy, and T.T. Narendran Selection of optimal conditions in multi-pass face-milling using a genetic algorithm International Journal of Machine Tools and Manufacture 40 3 2000 401 414
12. Z. Khan, B. Prasad, and T. Singh Machining condition optimization by genetic algorithms and simulated annealing Computers and Operations Research 24 7 1997 647 657
13. T. Szecsi A DC motor based cutting tool condition monitoring system Journal of Materials Processing Technology 92-93 1999 350 354
14. S. Achiche, M. Balazinski, L. Baron, and K. Jemielniak Tool wear monitoring using genetically-generated fuzzy knowledge bases Engineering Applications of Artificial Intelligence 15 3-4 2002 303 314
15. L. Li. Genetic Algorithm based open architecture cutting tool monitoring system, MS Thesis, Florida International University, 2002