Finite element modeling of machining of 1020 steel including the effects of round cutting edge

Transactions of the North American Manufacturing Research Institute of SME

Volumn 32, Issue , 2004, Pages 111-118

  Tian, Yinggang ^a   Shin, Yung C ^a  

^a PURDUE UNIVERSITY   (United States)

Author keywords

Finite Element Modeling; Metal Cutting; Round Cutting Edge

Indexed keywords

CHIP FORMATION; CUTTING FORCE; ORTHOGONAL MACHINING TEST; ROUND CUTTING EDGE;

ERROR ANALYSIS; FINITE ELEMENT METHOD; METAL CUTTING; PLASTICITY; STEEL; STRAIN RATE; STRESSES;

MACHINING;

EID: 10044274099     PISSN: 10473025     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (20)

1. Arsecularatne, J. A., (1997), "On Tool-chip Interface Stress Distributions, Ploughing Force and Size Effect in Machining," Int. J. Mach. Tools and Manuf., Vol. 37, No. 7, pp. 885-899.
2. Childs, T.H.C. and M.I. Mahdi, (1989), "On the Stress Distribution between the Chip and Tool during Metal Turning," Annals of the CIRP, Vol. 38, pp. 55-58.
3. Chuzhoy, L., R.E. Devor, S.G. Kapoor and D.J. Bammann, (2002), "Microstructure-Level Modeling of Ductile Iron Machining," ASME J. Manuf. Sci. Eng., Vol. 124, pp. 162-169.
4. Fang, N., (2003.a), "Slip-line Modeling of Machining with a Rounded-edge Tool-Part I: New Model and Theory," J. Mech. Phys. Solids, Vol. 51, pp.715-742.
5. Fang, N., (2003.b), "Slip-line Modeling of Machining with a Rounded-edge Tool-Part II: Analysis of the Size Effect and the Shear Strain-rate," J. Mech. Phys. Solids, Vol. 51, pp.743-762.
6. Gilat, A. and X. Wu, (1997), "Plastic deformation of 1020 steel over a wide range of strain rates and temperatures," Int. J. of Plasticity, Vol. 13, Issues 6-7, pp. 611-632.
7. Guo, Y.B. and C.R. Liu, (2002), "3D Modeling of Hard Turning," ASME J. Manuf. Sci. Eng., Vol. 124, pp. 189-199.
8. Lei, S., Y. C. Shin and F. P. Incropera, (1999.a), "Material Constitutive Modeling under High Strain Rates and Temperatures through Orthogonal Machining Tests," ASME J. Manuf. Sci. Eng., Vol. 121, pp. 577-585.
9. Lei, S., Y. C. Shin and F. P. Incropera, (1999.b), "Thermo- Mechanical Modeling of Orthogonal Machining Process by Finite Element Analysis," Int. J. Mach. Tools and Manuf., Vol. 39, 731-750.
10. Lei, S., (1999), Material Deformation Analysis and Characterization in Metal Cutting and Laser assisted Machining of Silicon Nitride, Ph.D. thesis, Purdue University, West Lafayette, IN Li, X., (1997), "Development of a Predictive Model for Stress Distribution at the Chip-tool Interface in Machining," Journal of Materials Processing Technology, Vol. 63, pp. 169-174.
11. Lei, S., (1999), Material Deformation Analysis and Characterization in Metal Cutting and Laser assisted Machining of Silicon Nitride, Ph.D. thesis, Purdue University, West Lafayette, IN Li, X., (1997), "Development of a Predictive Model for Stress Distribution at the Chip-tool Interface in Machining," Journal of Materials Processing Technology, Vol. 63, pp. 169-174.
12. Mackerle, J., (2003), "Finite Element Analysis and Simulation of Machining: an Addendum: A Bibliography (1996-2002)," Int. J. Mach. Tools and Manuf., Vol. 43, Issue 1, pp. 103-114.
13. Manjunathaiah, J. and W. J. Endre, (2000), "A New Model and Analysis of Orthogonal Machining with an Edge-radiused Tool," ASME J. Manuf. Sci. Eng., Vol. 122, pp. 384-390
14. McClain, B., S.A. Batzer and G.I. Maldonaldo, (2002), "A Numerical Investigation of the Rake Face Stress Distribution in Orthogonal Machining," Journal of Materials Processing Technology, Vol. 123, pp. 114-119.
15. Monaghan, J. and D. Brazil, (1998), "Modeling the Flow Processes of a Particle Reinforced Metal Matrix Composite During Machining," Composites Part A, Vol. 29A, pp. 87-99.
16. Ng, E.-G., D.K, Aspinwall, D. Brazil, and J. Monaghan, (1999), "Modeling of Temperature and Forces when Orthogonally Machining Hardened Steel," Int. J. Mach. Tools and Manuf., Vol. 39, pp. 885-903.
17. Ng, E.-G., T.I. El-Wardany, M. Dummitrescu and M.A. Elbestawi, (2002), "Physics-Based Simulation of High Speed Machining," Mach. Sci. Tech., Vol. 6, No. 3, pp. 301-329.
18. Oxley,P.L.B., (1989), The Mechanics of Machining: An Analytical Approach to Assessing Machinability, Halsted Press, New York
19. Özel, T. and T. Altan, (2000), "Determining of Workpiece Flow Stress and Friction at the Chip-Tool Contact for High-Speed Cutting," Int. J. Mach. Tools and Manuf., Vol. 40, pp. 133-152.
20. Zorev, N.N., (1963), "Inter-relationship between Shear Processes Occurring along Tool Face and Shear Plane in Metal Cutting," Proc. of the Int. Production Engineering Research Conf., Carnegie Institute of Technology, Pittsburgh, Pennsylvania, September 9-12, pp. 42-49.