Reduced quasi-dimensional combustion model of the direct injection diesel engine for performance and emissions predictions

KSME International Journal

Volumn 18, Issue 5, 2004, Pages 865-876

  Jung, Dohoy ^a   Assanis, Dennis N ^a  

^a UNIVERSITY OF MICHIGAN   (United States)

Author keywords

Combustion model; Diesel; Emissions; Multi zone; Quasi dimensional; Simulation

Indexed keywords

COMBUSTION EQUIPMENT; COMPUTER SIMULATION; FUEL ECONOMY; MACHINE DESIGN; OPTIMIZATION; OXIDATION; PARTICULATE EMISSIONS; SOOT; THERMODYNAMICS;

COMBUSTION MODEL; MULTI-ZONE; QUASI-DIMENSIONAL;

DIESEL ENGINES;

EID: 10044248995     PISSN: 12264865     EISSN: None     Source Type: Journal    
DOI: 10.1007/BF02990306     Document Type: Article

References (17)

1. Amsden, A. A., Ramshaw, J. D., O'Rourke, P. J., and Dukowicz, J. K., 1985, "KIVA: A Computer Program for Two- and Three-Dimensional Fluid Flow with Chemical Reactions and Fuel Sprays," Los Alamos National Laboratory Report, LA-10245-MS.
2. Assanis, D. N. and Heywood, J. B., 1986, "Development and Use of a Computer Simulation of the Turbocompounded Diesel System for Engine Performance and Component Heat Transfer Studies," SAE paper 860329.
3. Burt, R. and Troth, K. A., 1970, "Penetration and Vaporization of Diesel Fuel Sprays," Institution of Mechanical Engineers.
4. Chiu, W. S., Shahed, S. M. and Lyn, W. T., 1976, "A Transient Spray Mixing Model for Diesel Combustion," SAE Paper 760128.
5. Heywood, J. B., 1988, Internal Combustion Engine Fundamentals, McGraw-Hill Book Co.
6. Hiroyasu, H., Kadota, T. and Arai, M., 1983, "Development and Use of a Spray Combustion Modeling to Predict Diesel Engine Efficiency and Pollutant Emissions (Part 1 Combustion Modeling)," Bulletin of the JSME, Vol. 26, No. 214, pp. 569-575.
7. Hyroyasu, H. and Arai, M., 1980, "Fuel Spray Penetration and Spray Angle of Diesel Engines," Trans. of JSAE, Vol. 21, pp. 5-11.
8. Im, Y. H. and Huh, K. Y., 2000, "Phenomenological Combustion Modeling of a Direct Injection Diesel Engine with In-Cylinder Flow Effects," KSME International Journal, Vol. 14, No. 5, pp. 569-581.
9. Jung, D. and Assanis, D. N., 2001, "Multi-Zone DI Diesel Spray Combustion Model for Cycle Simulation Studies of Engine Performance and Emissions," SAE Trans.: Journal of Engines, Vol. 110, No. 3, pp. 1510-1532.
10. Kim, H. S. and Sung, N. W, 2001, "Multi-dimensional Engine Modeling : NO and Soot Emissions in a Diesel Engine with Exhaust Gas Recirculation, " KSME International Journal, Vol. 15, No. 8, pp. 1196-1204.
11. Lavoie, G. A., Heywood, J. B. and Keck, J. C., 1970, "Experimental and Theoretical Investigation of Nitric Oxide Formation in Internal Combustion Engines," Combust. Sci. Technol., Vol. 1, pp. 313-326.
12. Nehmer, D. A. and Reitz, R. D., 1994, "Measurement of the Effect of Injection Rate and Split Injections on Diesel Engine Soot and NOx Emissions," SAE Paper 940668.
13. Newman, J. A. and Brzustowski, T. A., 1971, "Behavior of a Liquid Jet Near the Thermodynamic Critical Region," AIAA journal, Vol. 9, No. 8.
14. Nishida, K. and Hiroyasu, H., 1989, "Simplified Three-Dimensional Modeling of Mixture Formation and Combustion in a D.I. Diesel Engine," SAE Paper 890269.
15. Waldman, C. H., Kau, C. J. and Wilson, R. P., Jr., 1974, "Prediction of Transient Temperature Fields within a Vaporizing/Burning Fuel Droplet under High Ambient Pressure," Western States Section, Combustion Institute, California State University at Northridge.
16. Watson, N., Pilley, A. D. and Marzouk, M. A., 1980, "Combustion Correlation for Diesel Engine Simulation," SAE Paper 800029.
17. Yeom, J. K., Lee, M. J., Chung, S. S., Ha, J. Y., Senda, J. and Fujimoto, H., 2002, "A Proposal for Diesel Spray Model Using a TAB Breakup Model and Discrete Vortex Method," KSME International Journal, Vol. 16, No. 4, pp. 532-548.