Mechanics of machining with chamfered tools

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 122, Issue 4, 2000, Pages 650-659

  Ren, H ^a   Altintas, Y ^a  

^a UNIVERSITY OF BRITISH COLUMBIA   (Canada)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 10044235101     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.1286368     Document Type: Article

References (21)

1. Merchant, M. E., 1945, “Mechanics of the Metal Cutting Process, II. Plasticity Conditions in Orthogonal Cutting,” J. Appl. Phys., 16, pp. 318-324.
2. Lee, E. H., and Shaffer, B. W., 1951, “The Theory of Plasticity Applied to A Problem of Machining,” Trans. ASME, J. Appl. Mech., 18, pp. 405-413.
3. Oxley, P. L. B., 1989, Mechanics of Machining-An Analytical Approach to Assessing Machinability, Ellis Horwood Limited.
4. Oxley, P. L. B., and Hastings, W. F., 1977, “Predicting the Strain Rate in the Zone of Intense Shear in Which the Chip is Formed in Machining From the Dynamic Flow Stress Properties of the Work Material and the Cutting Conditions,” Proceedings of the Royal Society of London, Vol. A356, pp. 395-410.
5. Hitomi, K., 1961, “Fundamental Machinability Research in Japan,” J. Eng. Ind., 83 pp. 531-544.
6. Jacobson, S., and Wallen, P., 1988, “A New Classification System For Dead Zone in Metal Cutting,” Int. J. Mach. Tools Manufact., 28, No. 4, pp. 529-538.
7. Hiraro, M., Tlusty, J., Sowerby, R., and Chandra, G., 1982, “Chip Formation with Chamfered Tools,” J. Eng. Ind., 104, pp. 339-342.
8. Waldorf, D. J., DeVor, R. E., and Kapoor, S. G., ASME 1997, “A Slip-line Field for Ploughing during Orthogonal Cutting,” 1997 ASME International Mechanical Engineering Congress and Exposition, MED-2, pp. 37-44.
9. Zhang, H. T., Liu, P. D., and Hu, R. S., 1991, “A Three Zone Model and Solution of Shear Angle in Orthogonal Machining,” Wear, 143, pp. 29-43.
10. Fuh, K., and Chang, C., 1995, “Prediction of the cutting forces for chamfered main cutting edge tools”, Int. J. Mach. Tools Manuf., 35-11, pp. 1559-1586.
11. Hastings, W. F., Mathew, P., and Oxley, P. L. B., 1980, “A Machining Theory for Predicting Chip Geometry, Cutting Forces, etc. from Work Material Properties and Cutting Conditions,” Proc. R. Soc. London, Ser. A, 371, pp. 569-587.
12. Boothroyd, G., 1963, “Temperatures in Orthogonal Metal Cutting,” Proc. Inst. Mech. Eng., 177, pp. 789-802.
13. Tay, A. O., Stevenson, M. G., De Vahl Davis, G., and Oxley, P. L. B., 1976, “A Numerical Method for Calculating Temperature Distributions in Machining, from Force and Shear Angle Measurements,” Int. J. Mach. Tool Des. Res., 16, pp. 335-349.
14. Stephenson, D. A., 1989, “Material Characterization for Metal-Cutting Force Modeling,” J. Eng. Mater. Technol., 111, pp. 210-219.
15. Gad, G. S., Armarego, E. J. A., and Smith, A. J. R., 1992, “Tool-Chip Contact Length in Orthogonal Machining and Its Importance in Tool Temperature Prediction,” Int. J. Prod. Res., 30, No. 3, pp. 485-501.
16. Zorev, N. N., 1996, Metal Cutting Mechanics, Pergamon, Oxford.
17. Shamoto, E., and Altintas, Y., 1999, “Prediction of Shear Angle in Oblique Cutting,” Trans. ASME J. Eng. Manufact. Sci. Eng., 121, pp. 399-407.
18. Budak, E., Altintas, Y., and Armarego, E. J. A., 1996, “Prediction of Milling Force Coefficients From Orthogonal Cutting Data,” J. Manuf. Sci. Eng., 118, pp. 216-224.
19. Johnson, W., Sowerby, R., and Haddow, J. B., 1970, Plane-Strain Slip-Line Fields: Theory and Bibliography, Edward Arnold LTD.
20. ASM International Handbook Committee, 1989, Metal Handbook Ninth Edition, 16, ASM, pp. 71-117.
21. Weiner, J. H., 1955, “Shear-Plane Temperature Distribution in Orthogonal Cutting,” Trans. ASME, 77, pp. 1331-1341.