Comparison of trip-strip/impingement/dimple cooling concepts at high reynolds numbers

American Society of Mechanical Engineers, International Gas Turbine Institute, Turbo Expo (Publication) IGTI

Volumn 5 A, Issue , 2003, Pages 703-709

  Kim, Yong W ^a   Arellano, Leonel ^a   Vardakas, Mark ^a   Moon, Hee Koo ^a   Smith, Kenneth O ^a  

^a SOLAR TURBINES INCORPORATED   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

IMPINGEMENT ARRAYS; MASS FLUX;

COMBUSTORS; COOLING; FRICTION; HEAT TRANSFER; JETS; REYNOLDS NUMBER; THERMAL CONDUCTIVITY; TRANSIENTS;

COMPUTATIONAL FLUID DYNAMICS;

EID: 0346335371     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/GT2003-38935     Document Type: Conference Paper

References (37)

1. Afanasyev, V.N., Chudnovsky, Ya.P., Leontiev, A.I., and Roganov, P.S., 1993, "Turbulent Flow Friction and Heat Transfer Characteristics for Spherical Cavities on a Flat Plate," Experimental Thermal and Fluid Science, 7:1-8, Elservier Science Publishing Co..
2. Bailey J.C., Tolpadi, A.K., Intile, J., Fric, T.F., Nirmalan, N.V., and Bunker, R.S., 2002, "Experimental and Numerical Study of Heat Transfer in a Gas Turbine Combustor Liner," ASME Paper GT-2002-30183, ASME Turbo Expo 2002, Amsterdam, The Netherlands.
3. Camci, C., Kim, K., Hippensteele, S.A., and Poinsatte, P.E., 1993, "Evaluation of Hue Capturing Based Transient Liquid Crystal Method for High-Resolution Mapping of Convective Heat Transfer on Curved Surfaces," ASME Journal of Heat Transfer, Vol. 115, pp. 311-318.
4. Chyu, M.K., Yu, Y., and Ding, H., 1997, "Concavity Enhanced Heat Transfer in an Internal Cooling Passage," ASME paper 97-GT-437, International Gas Turbine and Aeroengine Congress and Exposition, Orlando, Florida.
5. Dipprey, D.F., and Sabersky, R.H., 1963, "Heat and Momentum Transfer in Smooth and Rough Tubes at Various Prandtl Numbers," Int. J. Heat Mass Transfer, Vol. 6, pp. 329-353.
6. Dittus, F.W., and Boelter, L.M.K., 1930, Univ. Calif. (Berkeley) Pub. Eng., Vol.2, p. 443.
7. Ekkad, S.V., Zapata, D., and Han J.C., 1995, "Heat Transfer Coefficients over a Flat Surface with Air and CO2 Injection Through Compound Angle Holes Using a Transient Liquid Crystal Image Method," ASME Paper 95-GT-10, 95' Turbo Expo, Houston, Texas, June 5-8.
8. Florschuetz, L.W., Berry, R.A., and Metzger, D.E., 1980, "Periodic Streamwise Variations of Heat Transfer Coefficients For Inline And Staggered Arrays of Circular Jets With Crossflow of Spent Air," Trans. ASME, Journal of Heat Transfer, Vol. 102, Feb., pp. 132-137.
9. Florschuetz, L.W., Truman, C.R., and Metzger, D.E., 1981, "Streamwise Flow and Heat Transfer Distributions For Jet Array Impingement With Crossflow," Trans. ASME, Journal of Heat Transfer, Vol. 103, May, pp. 337-342.
10. Han, J.C., 1984, "Heat Transfer and Friction in Channels With Two Opposite Rib-Roughened Walls," Trans. ASME, Journal of Heat Transfer, Vol. 106, Nov., pp. 774-781.
11. Han, J.C., 1988, "Heat Transfer and Friction Characteristics in Rectangular Channels With Rib Turbulators," Trans. ASME, Journal of Heat Transfer, Vol. 110, May, pp. 321-328.
12. Han, J.C., and Park, J.S., 1988, "Developing Heat Transfer in Rectangular Channels With Rib Turbulators," Int. J. Heat Mass Transfer, Vol. 31, No.1, pp. 183-195.
13. Han, J.C., and Zhang, Y.M., 1992, "High Performance Heat Transfer Ducts With Parallel Broken And V-Shaped Broken Ribs," Int. J. Heat Mass Transfer, Vol. 35, No. 2, pp. 513-523.
14. Han, J.C., Glicksman, L.R., and Rohsenow, W.M., 1978, "An Investigation of Heat Transfer And Friction For Rib-Roughened Surfaces," Int. J. Heat Mass Transfer, Vol. 21, pp. 1143-1156.
15. Han, J.C., Huang, J.J., and Lee, C.P., 1993, "Augmented Heat Transfer in Square Channels With Wedge-Shaped and Delta-Shaped Turbulence Promoters," Enhanced Heat Transfer, Vol. 1, No.1, pp. 37-52.
16. Han, J.C., Park, J.S., and Lei, C.K., 1985, "Heat Transfer Enhancement in Channels With Turbulence Promoters," ASME, J. Engineering For Gas Turbines and Power, Vol. 107, July, pp. 628-635.
17. Herold, W., and Wiegel, D., 1980, "Problems of Photographic Documentation of Liquid Crystalline Thermographs," Advances in Liquid Crystal Research and Applications," L. Bata, ed., Pergamon Press, Oxford, pp. 1255-1259.
18. Höcker, R., 1996, "Optimization of Transient Heat Transfer Measurements Using Thermochromic Liquid Crystals Based on Error Estimation," ASME Paper 96-GT-235.
19. Ireland, P.T. and Jones, T.V., 1985, "The Measurement of Local Heat Transfer Coefficients in Blade Cooling Geometries," Proceedings of AGARD Conference on Heat Transfer and Cooling in Gas Turbines, CP. 390 Paper 28, Bergen.
20. Kercher, D.M., and Tabakoff, W., 1970, "Heat Transfer by a Square Array of Round Air Jets Impinging Perpendicular to a Flat Surface Including The Effect of Spent Air," ASME, Journal of Engineering for Power, Jan., pp.73-82.
21. Kesarev, V.S., and Kozlov, A.P., 1993, "Convective Heat Transfer in Turbulized Flow Past a Hemispherical Cavity," Heat Transfer Research, Vol. 25, No. 2, Scripta Technica, Inc.
22. Kline, S.J., and McClintock, F.A., 1953, "Describing Uncertainties in Single Sample Experiments," Mechanical Engineering, Vol. 75, pp. 3-8.
23. Larson, D.E., 1983, "Transient Local Heat Transfer Measurements in 90° Bends Using Surface Coatings Having Prescribed Melting Points," MS Thesis, Arizona State University.
24. Lau, S.C., Kukreja, R.T., and McMillin, R.D., 1991, "Effects of V-Shaped Rib Arrays on Turbulent Heat Transfer And Friction of Fully Developed Flow in a Square Channel," Int. J. Heat Mass Transfer, Vol. 34, No.7, pp. 1605-1616.
25. Lin, Y.-L., Shih, T. I-P., and Chyu, M.K., 1999, "Computations of Flow and Heat Transfer in a Channel with Rows of Hemispherical Cavities," ASME Paper 99-GT-263, Turbo Expo, Indianapolis, Indiana, June 7-10,.
26. Mahmood, G.I., Hill, M.L., Nelson, D.L., Ligrani, P.M., Moon, H.K., and Glezer, B., 2001, "Local Heat Transfer and Flow Structure on and Above a Dimpled Surface in a Channel," ASME, J. of Turbomachinery, Vol. 123, pp. 115-123.
27. Metzger, D.E., and Larson, D.E., 1986, "Use of Melting Point Surface Coatings for Local Convection Heat Transfer Measurements in Rectangular Channel Flows With 90-deg Turns," ASME, Journal of Heat Transfer, Vol. 108, pp. 48-54.
28. Moffat, R.J., 1988, "Describing the Uncertainties in Experimental Results, Experimental Thermal and Fluid Sciences, Vol. 1, pp. 3-17.
29. Moon, H.K., O'Connell, T., and Glezer, B., 2000, "Channel Height Effect on Heat Transfer and Friction in a Dimpled Passage," ASME, J. of Engineering for Turbines and Power, Vol. 122, pp.307-313.
30. Nikuradse, J., 1950, "Laws of Flow in Rough Pipes," VDI Forsch, 361 (1933), English Translation: NACA TM-1292
31. Rohsenow, W.M., and Hartnett, J.P., 1973, Handbook of Heat Transfer, McGraw-Hill, New York, pp. 7-122.
32. Schukin, A.V., Kozlov, A.P., and Agachev, R.S., 1995, "Study and Application of Hemispherical Cavities for Surface Heat Transfer Augmentation," ASME paper 95-GT-59, International Gas Turbine and Aeroengine Congress and Exposition, Houston, Texas.
33. Sheriff, N., and Gumley, P., 1966, "Heat-Transfer And Friction Properties of Surfaces With Discrete Roughnesses, " Int. J. Heat Mass Transfer, Vol. 9, pp. 1297-1320.
34. Terekhov, V.I., Kalinina, S.V., and Mshvidobadze, Y.M., 1995, "Flow Structure and Heat Transfer on a Surface with a Unit Hole Depression," Russian J. of Engineering Thermophysics, Vol. 5, pp. 11-34.
35. Vedula, R.J., and Metzger, D.E., 1991, "A Method for the Simultaneous Determination of Local Effectiveness and Heat Transfer Distributions in Three Temperature Convection Situations," ASME Paper 91-GT-345.
36. Webb, R.L., Eckert, E.R.G., and Goldstein, R.J., 1971, "Heat Transfer And Friction in Tubes With Repeated-rib Roughness," Int. J. Heat Mass Transfer, Vol. 14, pp. 601-617.
37. Yu, Y., and Chyu, M.K., 1996, "Influence of a Leaking Gap Downstream of the Injection Holes on Film Cooling Performance," ASME Paper 96-GT-175, ASME Turbo Expo '96, Birmingham, UK, June 10-13.