Design of an integrated motor/controller drive for an automotive water pump application

Conference Record-IAS Annual Meeting (IEEE Industry Applications Society)

Volumn 3, Issue , 2002, Pages 2028-2035

  Harris, Nathan C ^a   Jahns, Thomas M ^a   Huang, Surong ^a  

^a University of Wisconsin Madison   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

ELECTRIC FILTERS; ELECTRIC MOTORS; FINITE ELEMENT METHOD; PUMPS; SIGNAL INTERFERENCE; THERMOANALYSIS;

AUTOMOTIVE WATER PUMPS;

ELECTRIC DRIVES;

EID: 0036445177     PISSN: 01972618     EISSN: None     Source Type: Journal    
DOI: 10.1109/IAS.2002.1043811     Document Type: Article

References (19)

1. J.G. Kassakian, "Automotive Electrical Systems-The Power Electronics Market of the Futures", in Proc. of 2000 IEEE Appl. Power Elec. Conf. (APEC), New Orleans, Feb. 2000, pp. 3-9.
2. H. Couetoux, "Cooling System Control in Automotive Engines", Paper No. 920788, Society of Automotive Engineers, 1992, pp. 153-160.
3. EWP Electric Water Pump, Davies Craig Pty Ltd., Website: http://www.daviescraig.com.au.
4. "Fluid Pump", US Patent #6,056,518, D.J. Allen, B.K. Larche and K.A. DeGrave, assigned to Engineered Machined Products, May 2, 2000.
5. Controllable Fluid Pump, Engineered Machined Products Corp., Website: http://www.emp-corp.com/html/products/controllable_fiuid_pump.shtml.
6. "Road Vehicles-Conditions for Electrical and Electronic Equipment for a 42V Powernet", Working Draft, WGS/WD03/200-1, Working Group "Standardization", Forum Bordnetz, Germany, April 2000.
7. "Limits and Methods of Measurement of Radio Disturbance Characteristics of Components and Modules for the Protection of Receivers Used on Board Vehicles", SAE Standard J1113/41, Society of Automotive Engineers, July 1995.
8. T.J.E. Miller, Brushless Permanent Magnet and Reluctance Motor Drives, Clarendon Press, Oxford, UK, 1989.
9. T.M. Lipo, Introduction to Machine Design, Volume I, Univ. of Wisconsin, Madison, 1996.
10. S. Huang, J. Luo, F. Leonardi, T.A. Lipo, "A Comparison of Power Density for Axial Flux Machines Based on General Purpose Sizing Equations", IEEE Trans. on Energy Conversion, vol. 14, no. 2, June 1999, pp. 185-191.
11. S. Huang, J. Luo, F. Leonardi, T.A. Lipo, "A General Approach to Sizing and Power Density Equations for Comparison of Electrical Machines", IEEE Trans on Industry Appl., vol. 34, no. 1, Jan/Feb 1998, pp. 92-97.
12. N.C. Harris, "Low Cost Integrated Motor Drives for Automotive Accessory Applicatons", M.S. Thesis, University of Wisconsin-Madison, August 2001.
13. E.C. Lovelace, "Optimization of a Magnetically Saturable Interior Permanent-Magnet Synchronous Machine Drive", PhD. Thesis, Massachusetts Institute of Technology, June 2000.
14. E.C. Lovelace, T.M. Jahns, and J.H. Lang, "Impact of Saturation and Inverter Cost on Interior PM Synchronous Machine Drive Optimization", IEEE Trans. Ind. Appl., vol. 36, pp. 723-729, May/June 2000.
15. A.M. EL-Refaie, N.C. Harris, T.M. Jahns, K.M. Rahman, "Thermal Analysis of Multi-Barrier IPM Synchronous Machine using Lumped Parameter Model", in Proc. Intl. Conf. on Elec. Machines (ICEM), Brugges, Belgium, August 2002.
16. J.D. Van Wyk and F.C. Lee, "Power Electronics Technology at the Dawn of the New Millennium-Status and Future", in Proc. of 1999 IEEE Power Electronics Spec. Conference (PESC), Charleston, SC, June 1999, pp. 3-12.
17. Y. Xiao, R. Natarajan, J. Rymaszewski, T.P. Chow, R.J. Gutmann, "Flip-chip Flex-Circuit Packaging Implemented for 42V/16A Integrated Power Electronics Module Applications", in Proc. IEEE Appl. Pow. Elec. Conf. (APEC), Dallas, Feb. 2002, pp. 21-26.
18. D. Giacomini, E. Bianconi, L. Martino, M. Palma, "A New Fully Integrated Power Module for Three Phase Servo Motor Drive Applications", in Rec. of 2001 IEEE Industry Applications Society Annual Meeting, Chicago, Oct. 2001, pp. 981-987.
19. S. Parler. "Thermal Modeling of Aluminum Electrolytic Capacitors", in Rec. of 1999 IEEE Industry Applications Society Annual Meeting, Phoenix, Oct. 1999, pp. 2418-2429.