Increased chemisorption onto activated carbon after ball-milling

Carbon

Volumn 40, Issue 13, 2002, Pages 2307-2315

  Welham, N J ^a,d   Berbenni, V ^b   Chapman, P G ^c  

^a AUSTRALIAN NATIONAL UNIVERSITY   (Australia)

^b UNIVERSITY OF PAVIA   (Italy)

^c CURTIN UNIVERSITY   (Australia)

^d MURDOCH UNIVERSITY   (Australia)

Author keywords

A. Activated carbon; B. Grinding; C. Thermal analysis (DTA and TGA), BET surface area; D. Adsorption properties

Indexed keywords

ADSORPTION; ARGON; BALL MILLING; CARBON DIOXIDE; CHEMISORPTION; FOURIER TRANSFORM INFRARED SPECTROSCOPY; GRINDING (COMMINUTION); THERMOGRAVIMETRIC ANALYSIS; WATER;

SURFACE AREAS;

ACTIVATED CARBON;

EID: 0036042288     PISSN: 00086223     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0008-6223(02)00123-9     Document Type: Article

References (52)

1. Raman spectra of graphite and diamond mechanically milled with agate or stainless steel ball-mill
2. Structural disorder and phase transformation in graphite produced by ball milling
3. Amorphization of graphite induced by mechanical milling and subsequent crystallization of the amorphous carbon upon heat treating
4. A transmission electron microscopy study of amorphization of graphite by mechanical milling
5. Structural transformations induced in graphite by grinding: Analysis of 002 X-ray diffraction line profiles
6. Raman spectra of ground natural graphite
7. Effect of atmosphere on the mechanical milling of natural graphite
8. Structure and chemical reactivity of ball-milled graphite
9. Effect of mixed-grinding on reduction process of carbonaceous material and iron oxide composite
10. Mechanochemical reduction of CuO by graphite
11. A parametric study of the mechanically activated carbothermic reduction of ilmenite
12. The effect of extended milling on minerals
13. Enhancement of the Becher process by ball milling
14. Room-temperature mechanosynthesis of carbides by grinding of elemental powders
15. Formation mechanism of TiC by mechanical alloying
16. Mechanosynthesis of tungsten carbide
17. Ball-milling of Fe-C (20-75% Fe)
18. 3
19. 4)
20. A novel route to micronised tungsten carbide
21. 2
22. Reactivity of mechanically activated chalcopyrite
23. Structure-reactivity study of mechanically activated zinc ferrite
24. Influence of solid state properties on ferric chloride leaching of mechanically activated galena
25. 4
26. Mechanical enhancement of the dissolution of ilmenite
27. Enhanced dissolution of tantalite/columbite following milling
28. Thermal decomposition of mechanically activated arsenopyrite
29. Reactivity of mechanically activated pyrite
30. Effect of extended grinding on the dissolution of a Ta/Nb concentrate
31. Extended milling of graphite and activated carbon
32. Effect of mechanical grinding on the lithium intercalation process in graphites and soft carbons
33. Nanoporous carbon produced by ball milling
34. Universal high performance ball milling device and its application for mechanical alloying
35. 2 molecules on the surface of solids
36. Adsorption of gases in multimolecular layers
37. Structural analysis of the B-doped mesophase pitch-based graphite fibers by raman spectroscopy
38. UV studies of tetrahedral bonding in diamondlike amorphous carbon
39. Raman spectroscopy on amorphous carbon films
40. Structure, dynamics, and electronic properties of diamondlike amorphous carbon
41. Vibrational modes of carbon nanotubes - Spectroscopy and theory
42. Characterization of fullerenes and carbon nanoparticles generated with a laser-furnace technique
43. The importance of active surface area in the carbon-oxygen reaction
44. Active centres produced in graphite by powdering
45. Cross-sectional areas of molecules adsorbed on solid surfaces
46. Surface area and pore size distribution of microporous carbon fibers prepared by electrochemical oxidation
47. 2
48. On the connection between ultrafine grinding and mechanical activation of minerals
49. Energy transfer and conversion during comminution and mechanical activation
50. Milling dynamics. 2. Dynamics of a Spex mill and a one-dimensional mill
51. Milling dynamics. 3. Integration of local and global modeling of mechanical alloying devices