Oxley modeling approach, its applications and future directions

Machining Science and Technology

Volumn 4, Issue 3, 2000, Pages 363-397

  Arsecularatne, J A ^a   Mathew, P ^a  

^a UNIVERSITY OF NEW SOUTH WALES   (Australia)

Author keywords

[No Author keywords available]

Indexed keywords

CUTTING TOOLS; DEFORMATION; MATHEMATICAL MODELS; STRAIN RATE; TEMPERATURE; THERMAL STRESS; THERMODYNAMIC PROPERTIES;

CUTTING FORCES; HIGH TEMPERATURE FLOW STRESS; ORTHOGONAL PROCESS; OXLEY MACHINING THEORY;

MACHINING;

EID: 0034478931     PISSN: 10910344     EISSN: None     Source Type: Journal    
DOI: 10.1080/10940340008945716     Document Type: Article

References (41)

1. Oxley, P. L. B., Mechanics of Machining: An Analytical Approach to Assessing Machinability, Ellis Horwood, Chichester, (1989).
2. Palmer, W. B., Oxley, P. L. B, Mechanics of Metal Cutting, Proc. Inst. Mech. Engrs, 173, (1959), 623-654.
3. Stevenson, M. G., Oxley, P. L. B., An Experimental Investigation of the Influence of Speed and Scale on the Strain-Rate in a Zone of Intense Plastic Deformation, Proc. Inst. Mech. Engrs, 184, (1969-1970), 561-576.
4. Merchant, M. E., Basic Mechanics of Metal Cutting Process, J. Appl. Mech., 11, (1944), A168-A175.
5. Boothroyd, G., Temperatures in Orthogonal Metal Cutting. Proc. Inst. Mech. Engrs, 177, (1963), 789-802.
6. Trent, E. M., Metal Cutting, Butterworths, Guilford, (1977).
7. Challen, J. M., Oxley, P. L. B., A Slipline Field Analysis of the Transition from Local Asperity Contact to Full Contact in Metallic Sliding Friction, Wear, 100, (1984), 171-193.
8. Oxley, P. L. B., Hastings, W. F., Predicting the Strain-Rate in the Zone of Intense Shear in which the Chip is Formed in Machining from the Dynamic Flow Stress Properties of the Work Material and Cutting Conditions, Proc. R. Soc. Lond., A356, (1977), 395-410.
9. Oxley, P. L. B., Hastings, W. F., Minimum Work as a Possible Criterion for Determining the Frictional Conditions at the Tool/Chip Interface in Machining, Phil. Trans. R. Soc. Lond., 282, (1976), 565-584.
10. Hu, R. S., Mathew, P., Oxley, P. L. B., Young, H. T., Allowing for End Cutting Edge Effects in Predicting Forces in Bar Turning with Oblique Machining Conditions, Proc. Inst. Mech. Engrs, C200, (1986), 89-99.
11. Young, H. T., Mathew, P., Oxley, P. L. B., Allowing for Nose Radius Effects in Predicting the Chip Flow Directions and Cutting Forces in Bar Turning, Proc. Inst. Mech. Engrs, C201, (1987), 213-226.
12. Wang, J., Mathew, P., Development of a General Tool Model for Turning Operations based on a Variable Flow Stress Theory, Int. J. Mach. Tools Manufact., 35, (1995), 71-90.
13. Arsecularatne, J. A., Mathew, P., Oxley, P. L. B., Prediction of Chip Flow Direction and Cutting Forces in Oblique Machining with Nose Radius Tools, Proc. Inst. Mech. Engrs, B209, (1995), 305-315.
14. Arsecularatne, J. A., Fowle, R. F., Mathew, P., Oxley, P. L. B., Prediction of Cutting Forces and Built-Up Edge Formation Conditions in Machining with Oblique Nose Radius Tools, Proc. Inst. Mech. Engrs, B210, (1996), 457-469.
15. Lin, G. C. I., Mathew, P., Oxley, P. L. B., Watson, A. R., Predicting Cutting Forces for Oblique Machining Conditions, Proc. Inst. Mech. Engrs, 196, (1982), 141-148.
16. Oyane, M., Takashima, F., Osakada, K., Tanaka, H., The Behaviour of Some Steels Under Dynamic Compression, Proc 10th Japan Congress on Testing Materials, (1967), 75-76.
17. MacGregor, C. W., Fisher, J. C., A Velocity-Modified Temperature for the Plastic Flow of Metals, J. Appl. Mech., 13, (1946), Al 1-A16.
18. Campbell, J. D., Ferguson, W. G., The Temperature and Strain-Rate Dependence of the Shear Strength of Mild Steel, Phil. Mag., 21 (8th Series), (1970), 63-81.
19. Woolman, J., Mottram, R. A., The Mechanical and Physical Properties of the British En Steels, British Iron and Steel Research Association, Pergamon, Oxford, (1964).
20. Tay, A. O., Stevenson, M. G., de Vahl Davis, G., Oxley, P. L. B., A Numerical Method for Calculating Temperature Distributions in Machining from Force and Shear Angle Measurements, Int. J. Mach. Tool Des. Res., 16, (1976), 335-349.
21. Hastings, W. F., Mathew, P., Oxley, P. L. B., A Machining Theory for Predicting Chip Geometry, Cutting Forces etc., from Work Material Properties and Cutting Conditions, Proc. R. Soc. Lond., A371, (1980), 569-587.
22. Mathew, P., Oxley, P. L. B., Predicting the Effects of Very High Cutting Speeds on Cutting Forces, etc, CIRP Annals, Vol. 31/1, (1982), 49-52.
23. Oxley, P. L. B., Predicting the Influence of Ultra High Cutting Speeds on Machining, Proc. Int. Conf. Prec. Engg., Taipei, Taiwan, R.O.C., 20-22 Nov., 1, (1997), 19-24.
24. Chisholm A. J., The Characteristics of Machined Surfaces, Machinery (London), No. 1910, (1949), 729-736.
25. Ansell C. T. and Taylor J., The Surface Finishing Properties of a Carbide and Ceramic Cutting Tool, Advances in Machine Tool Design and Research, Oxford: Pergamon Press Ltd., (1962), 225-240.
26. Takeyama, H. and Murata, R., Basic Investigation of Tool Wear, Trans. ASME, J. Eng. Ind., 85, (1963), 33-38.
27. Arsecularatne, J. A., Fowle, R. F., Mathew, P. and Oxley, P. L. B., Prediction of Tool Life in Oblique Machining with Nose Radius Tools, Wear, 198, (1996), 220-228.
28. V. I. Nachev and P. L. B. Oxley, Predicting cutting conditions giving plastic deformation of the cutting edge in terms of tool and work material properties, Proc. 25th Int MTDR Conf., Macmillan, London, (1985), 225-230.
29. Meng, Q., Arsecularatne, J. A. and Mathew, P., Prediction of the Cutting Conditions Giving Plastic Deformation of the Tool in Oblique Machining, Int. J. Mach. Tools Manufact., 38, (1998), 1165-1182.
30. M. Kronenberg, Machining Science and Application: Theory and Practice for Operation and Development of Machining Process, Pergamon Press. (1966).
31. Arsecularatne, J. A., On Tool-Chip Interface Stress Distributions, Ploughing Force and Size Effect in Machining, Int. J. Mach. Tools Manufact., 37, (1997), 885-899.
32. E. M. Trent, Hot Compressive Strength Of Cemented Carbides, Proc. 8th Int MTDR Conf. Manchester, (1968), 629-642.
33. Arsecularatne, J. A. and Oxley P. L. B., Prediction of Cutting Forces in Machining with Restricted Contact Tools, Machining Science and Technology, 1, (1997), 95-112.
34. Arsecularatne, J. A. and Mathew, P., Prediction of Tool Life in Machining with Restricted Contact Tools, accepted for publication Machining Science and Technology (Marcel Dekker).
35. Wright P. K., McCormick S. P. and Miller T. R., Effect of Rake Face Design on Cutting Tool Temperature Distributions, Trans. ASME, J. Eng. Ind., 102, (1980), 123-128.
36. Young, H. T., Mathew, P., Oxley, P. L. B., Predicting Cutting Forces in Face Milling, Int. J. Mach. Tools Manufact., 34, (1994), 771-783.
37. Narimani, R. Mathew, P., Evaluation of Thrust Force and Cutting Torque in Reaming, Proc 4th Int Conf on Adv Manuf Systems and Tech, Udine, Italy, 1-2 September, (1996), 107-114. (editor E Kuljanic, Springer Verlag, Wien, New York).
38. th Int. Conf. on Manufact. Engg., Sydney, Australia, 27-30 Aug, paper P02C.02 (2000) ISBN 0646399012
39. Bao, H., Stevenson, M. G., A Basic Mechanism for Built-up Edge Formation in Machining, CIRP Annals, 25/1, (1976), 53-57.
40. Kopalinsky, E. M., Oxley, P. L. B., Predicting the effects of Cold Working on the Machining Characteristics of Low Carbon Steels, J. Eng. Ind., 109, (1987), 257-264.
41. Watson, A. R., The Theoretical Prediction of Torques and Thrust in Drilling, PhD Thesis, The University of New South Wales, (1984).