Prototyping of patellar components using morphometrical data, principal component analysis and CAD/CAE techniques

Automedica

Volumn 18, Issue 1, 1999, Pages 27-45

  Low, F H ^a   Khoo, L P ^a   Chua, C K ^a   Lo, N N ^a  

^a NANYANG TECHNOLOGICAL UNIVERSITY   (Singapore)

Author keywords

CAD CAE; Morphology; Patella; Principal component analysis; Rapid prototyping

Indexed keywords

COMPUTER AIDED DESIGN; COMPUTER AIDED ENGINEERING; PRINCIPAL COMPONENT ANALYSIS;

PATELLAR COMPONENTS;

SOFTWARE PROTOTYPING;

ARTICLE; ASIA; CAUCASIAN; COMPUTER ANALYSIS; COMPUTER PROGRAM; CONTROLLED STUDY; HUMAN; KNEE PROSTHESIS; MAJOR CLINICAL STUDY; MORPHOMETRICS; MULTIVARIATE ANALYSIS; PATELLA; PRINCIPAL COMPONENT ANALYSIS; SINGAPORE; STATISTICAL ANALYSIS; TOTAL KNEE REPLACEMENT;

EID: 0033361047     PISSN: 00950963     EISSN: None     Source Type: Journal    
DOI: None     Document Type: Article

References (40)

1. Anatomic Alignment of the Patellar Groove
2. Influence of Soft Structures on Patellar Three-Dimensional Tracking
3. The Effect of Trochlear Design on Patellofemoral Shear and Compressive Forces in Total Knee Arthroplasty
4. Differences in Patellar Tracking and Knee Kinematics Among Three Different Total Knee Designs
5. Patellofemoral Joint Kinematics and Contact Pressures in Total Knee Arthroplasty
6. Why Not Resurface The Patella?
7. The Patellofemoral Joint in Total Condylar Knee Arthroplasty
8. Comparison of Patellar Resurfacing Versus Nonresurfacing in Bilateral Total Knee Arthroplasty
9. Total Knee Arthroplasty Without Patellar Resurfacing
10. Should the Patella Be Resurfaced in Total Knee Arthroplasty?
11. Total Knee Arthroplasty without Patellar Resurfacing
12. Patellar Resurfacing Versus Retention in Total Knee Arthroplasty
13. Is There a Place for Patellofemoral Arthroplasty?
14. The Patellofemoral Component of Total Knee Arthroplasty
15. Knee Morphology as a Guide to Knee Replacement
16. Studies on the Sizes and Shapes of Japanese knees and their application to the Design of Knee Prosthesis
17. A study of Chinese Knee Joint Geometry for Prosthesis Design
18. Parametric modelling of a knee joint prothesis
19. Effects of Patellar Thickness on Compression and Shear Forces in Total Knee Arthroplasty
20. The Effects of Patellar Thickness on Patellofemoral Forces After Resurfacing
21. Patellar Component Failure in Cementless Total Knee Arthroplasty
22. Technique for Patellar Resurfacing in Total Knee Arthroplasty
23. Technical Considerations in Total Knee Arthroplasty
24. Fracture of the Patella after Total Knee Arthroplasty
25. Effect of patellar thickness on patella strain following to total knee arthroplasty
26. Sex determination by discriminate analysis of patella measurements
27. Patella Prosthesis Positioning in Total Knee Arthroplasty. A Roentgenographic Study
28. "Patellar Resurfacing in Total Knee Arthroplasty"
29. Patellar Tilt and Subluxation in Total Knee Arthroplasty
30. Failure Mechanism of Metal-Back Patellar components
31. Further observations on metal-backed Patellar Component Failure
32. A Metal-Backed, Rotating-Bearing Patellar Prosthesis to Lower Contact Stress
33. Evaluation of Contact Stress in Metal-Backed Patellar Replacements
34. All-Polyethylene Patellar Components Are Not the Answer
35. Metal-on-Metal Total Hip Replacements
36. The Use of Metal-Backed Patellar Prostheses in Total Knee Arthroplasty
37. Patellar Forces during Knee Extensions