Application of an internally consistent material model to determine the effect of tool edge geometry in orthogonal machining

American Society of Mechanical Engineers, Manufacturing Engineering Division, MED

Volumn 10, Issue , 1999, Pages 327-335

  Schimmel, Roy J ^a   Endres, William J ^a   Stevenson, Robin ^b  

^a UNIVERSITY OF MICHIGAN   (United States)

^b GENERAL MOTORS CORPORATION   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CUTTING TOOLS; ZINC;

TOOL EDGE GEOMETRY;

METAL CUTTING;

EID: 0033331892     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Article

References (23)

1. Abebe, M., and Appl, F. C., 1981, "A Slip-Line Solution for Negative Rake Angle Cutting," Proc., NAMRC 19, Vol. 19, pp. 341-348.
2. Albrecht, P., 1960, "New Developments in the Theory of Metal Cutting Process: Part I - The Ploughing Process in Metal Cutting," ASME J. of Engg. for Ind., Vol. 82, pp. 348-357.
3. Albrecht, P., 1961, "New Developments in the Theory of Metal Cutting Process: Part II - The Theory of Chip Formation," ASME J. of Engg. for Ind., Vol. 83, pp. 557-568.
4. Backer, W. R., Marshall E. R., and Shaw, M. C., 1952, "The Size Effect in Metal Cutting," Trans. ASME, Vol. 74, pp. 61-72.
5. Colwell, L. V., 1971, "Methods for Sensing the Rate of Tool Wear," Annals of CIRP, Vol. 19, pp. 647.
6. Colwell, L. V., and Mazur, J. C., 1976, "Tool Wear Tracking in the Production Shop," Proc., NAMRC 4, pp. 420.
7. Connolly, R., and Rubenstein, C., 1968, "The Mechanics of Continuous Chip Formation in Orthogonal Cutting," Int. J. Mach. Tool Des. Res., Vol. 8, pp. 159-187.
8. Endres, W. J., Devor, R. E., and Kapoor, S. G., 1995, "A Dual Mechanism Approach to the Prediction of Machining Forces - Parts 1 & 2," ASME J. of Engg. for Ind., Vol. 117, pp. 526-542.
9. Kececioglu, D., 1958, "Shear-Strain Rate in Metal Cutting and its Effects on Shear-Flow Stress," Trans. ASME, Vol. 80, pp. 158-168.
10. Komanduri, R., 1971, "Some Aspects of Machining with Negative Rake Tools Simulating Grinding," Int. J. Mach. Tool Des. Res., Vol. 11, pp. 223-233.
11. Manjunathaiah, J., Endres, W. J., 1999, "Modeling the Apparent Rake Angle for Orthogonal Machining with Edge Radiused Tools," Int. J. Mach. Sci. and Tech., to be published.
12. Masuko, M., 1953, "Fundamental Research on Metal Cutting (1st Report), A New Analysis of Cutting Forces," Trans. JSME, Vol. 19, pp. 32-39
13. Merchant, M. E., 1945, "Mechanics of the Metal Cutting Process: I - Orthogonal Cutting and the Type 2 Chip," J. of Applied Physics, Vol. 16, pp. 267-275.
14. Oxley, P. L. B., 1989, The Mechanics of Machining: An Analytical Approach to Assessing Machinability, Ellis Horwood Limited, Chichester.
15. Thomsen, E. G., Lapsley, J. T., and Grassi, R. C., 1953, "Deformation Work Absorbed by the Workpiece During Metal Cutting," Trans. ASME, Vol. 75, pp. 591-603.
16. Schimmel, R. J., Manjunathaiah, J., Endres, W. J., 1997, "An Experimental Investigation of the Variability of Edge Hones and Their Effects on Machining Forces," Proc. ASME IMECE, Vol. MED-6-2, pp. 261-267.
17. Stevenson, R., and Stephenson, D. A., 1995, "The Mechanical Behavior of Zinc During Machining," ASME J. of Engg. for Ind., Vol. 117, pp. 172-178.
18. Stevenson, R., and Stephenson, D. A., 1996, "The Effect of Prior Cutting Conditions on the Shear Mechanics of Orthogonal Machining," ASME J. Man. Sci. Eng., Vol. 120, pp. 13-20.
19. Stevenson, R., 1998, "The Measurement of Parasitic Forces in Orthogonal Cutting," Int. J. Mach. Tools Manufact., Vol. 38, pp. 113-130.
20. Stevenson, R., 1999, "A Reassessment of Extrapolation Technique for Determining Parasitic Cutting Loads in Strain Rate Hardening Materials," Mach. Sci. and Tech., to be published.
21. Wagoner, R. H., 1981, "A Technique for Measuring Strain Rate Sensitivity," Metallurgical Transactions A, Vol. 12A, pp. 71-75.
22. Waldorf, D. J., 1996, "Shearing, Ploughing and Wear in Orthogonal Machining," PhD Thesis, University of Illinois at Urbana-Champaign.
23. Wu, D. W., 1988, "Application of a Comprehensive Dynamic Cutting Force Model to Orthogonal Wave Generating Processes," Int. J. of Mech. Sci., Vol. 30, no.8, pp. 581-600.