Drilling burr formation in titanium alloy, Ti-6Al-4V

CIRP Annals - Manufacturing Technology

Volumn 48, Issue 1, 1999, Pages 73-76

  Dornfeld, D A ^a   Kim, J S ^a   Dechow, H ^a   Hewson, J ^a   Chen, L J ^b  

^a UNIVERSITY OF CALIFORNIA   (United States)

^b United Technology Research Center   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CARBIDE CUTTING TOOLS; COMPOSITION EFFECTS; COOLANTS; GEOMETRY; TEMPERATURE CONTROL; THERMAL EFFECTS; TITANIUM ALLOYS; WEAR OF MATERIALS;

DRILLING BURR FORMATION; TOOL GEOMETRY;

DRILLING;

EID: 0032652052     PISSN: 00078506     EISSN: None     Source Type: None    
DOI: 10.1016/S0007-8506(07)63134-5     Document Type: Article

References (18)

1. Donachie, M. J., 1982, Titanium and titanium alloys, American Society for Metals, 3-19.
2. Boyer, R., Welsch, G., Collings, E. W., 1994, Materials properties handbook: Titanium alloys, The materials information society, ASM International, Materials Park.
3. Kahles, J. F., Field, M., Eylon, D., Froes, F. H., 1985, Machining of titanium alloys, Journal of metals, 27-35.
4. Komanduri, R. and von Turkovich, B. F., 1981, New observations on mechanism of chip formation when machining titanium alloys, Wear, 69:179-188.
5. Hartung, P. and Kramer, B., 1982, Tool wear in titanium machining, CIRP Annals, 31/1:75-80.
6. Sakurai, K., Adachi, K., Niba, R., Ogawa, K., 1992, Drilling of Ti-6A1-4V alloy, Keikinzoku (J. Japan Inst. Light Metals), 42/7:389-394
7. Sakurai, K., Adachi, K., Niba, R., Ogawa, K., 1992, Low frequency vibratory drilling of Ti-6AI-4V alloy, Keikinzoku (J. Japan Inst. Light Metals), 42/11:633-637.
8. Arai, M. and Ogawa, M., 1997, Effects of high pressure supply of coolant in drilling titanium alloy, Keikinzoku (J. Japan Inst. Light Metals), 47/3:39-144.
9. Gillespie, L. K., 1975, Burrs produced by drilling, Bendix Corporation Unclassified Topical Report, BDX-613-1248.
10. Sofronas, A., 1975, The formation and control of drilling burrs, Ph.D. Dissertation, University of Detroit.
11. Shikata, H., DeVries, M., and Wu, S., 1980, An experimental investigation of sheet metal drilling, CIRP Annals, 29/1:85-88.
12. Stein J., Dornfeld, D., 1997, Burr formation in drilling miniature holes, CIRP Annals, 46:63-66.
13. Link, R., 1992, Gratbildung und Strategien zur gratreduzierung bei der zerspanung mit geometrisch bestimmter schneide, Ph. D. dissertation, RWTH Aachen, Germany.
14. Guo, Y. B. and Dornfeld, D. A., 1998, Finite Element Analysis of drilling burr minimization with a backup material, Trans. NAMRI, SME, 26:207-212.
15. Dechow, H., 1998, Influence of the tool on hole quality when drilling Ti-6AI-4V including the aspects of reaming, Diploma-Thesis Study, LMA, University of California-Berkeley.
16. Communication with Dr. Chen, L. J. and Dr. El-Wardany, T., of United Technology Research Center.
17. Barish, H., 1988, Quality drills contribute to successful titanium tooting, Cutting tool engineering, 40/1:38-42.
18. Ko, S. L., 1989, Burr formation and fracture mechanism at the exit stage of machining metals, Ph.D. Dissertation, Mechanical Engineering, Univ. of California, Berkeley.