Bolted connection design for sheet steels less than 1.0 mm thick

Journal of Constructional Steel Research

Volumn 51, Issue 2, 1999, Pages 123-146

  Rogers, C A ^a   Hancock, G J ^a  

^a UNIVERSITY OF SYDNEY   (Australia)

Author keywords

Bolts; Connections; Design; Standards; Steel structures; Thin sections

Indexed keywords

SHEAR TESTING;

BEARING CAPACITY; BOLTED JOINTS; FAILURE ANALYSIS; SHEAR STRESS; STANDARDS; STEEL SHEET; STRUCTURAL ANALYSIS;

STEEL STRUCTURES;

EID: 0032650708     PISSN: 0143974X     EISSN: None     Source Type: Journal    
DOI: 10.1016/S0143-974X(99)00018-8     Document Type: Article

References (35)

1. Standards Australia/Standards New Zealand. Cold-formed steel structures - AS/NZS 4600. Sydney, NSW, Australia, 1996.
2. American Iron and Steel Institute. 1996 Edition of the Specification for the Design of Cold-Formed Steel Structural Members. Washington, DC, USA, 1997.
3. Canadian Standards Association, S136. Cold Formed Steel Structural Members. Etobicoke, Ont., Canada, 1994.
4. Dhalla A.K., Winter G. Steel ductility measurements. Journal of the Structural Division, ASCE. 100(ST2):1974;427-444.
5. Dhalla A.K., Winter G. Suggested steel ductility requirements. Journal of the Structural Division, ASCE. 100(ST2):1974;445-462.
6. Standards Australia. Steel sheet and strip - hot-dipped zinc-coated or aluminium/zinc coated - AS 1397. Sydney, NSW, Australia, 1993.
7. Rogers CA, Hancock GJ. Ductility of G550 sheet steels in tension - elongation measurements and perforated tests. Research Report No. R735, Centre for Advanced Structural Engineering, University of Sydney, Sydney, NSW, Australia, 1996.
8. Rogers CA, Hancock GJ. Ductility of G550 sheet steels subjected to tension. Proceedings of the 5th International Colloquium on Stability and Ductility of Steel Structures, Japanese Society of Steel Construction and Nagoya University, Nagoya, Japan, 1997:949-956.
9. Rogers C.A., Hancock G.J. Ductility of G550 sheet steels in tension. Journal of Structural Engineering ASCE. 123(12):1997;1586-1594.
10. Rogers CA, Hancock GJ. Bolted connection tests of thin G550 and G300 sheet steels. Research Report No. R749, Centre for Advanced Structural Engineering, University of Sydney, Sydney, NSW, Australia, 1997.
11. Rogers C.A., Hancock G.J. Bolted connection tests of thin G550 and G300 sheet steels. Journal of Structural Engineering, ASCE. 124(7):1998;798-808.
12. Rogers CA, Hancock GJ. New bolted connection design formulae for G550 and G300 sheet steels less than 1.0 mm thick. Research Report No. R769, Centre for Advanced Structural Engineering, University of Sydney, Sydney, NSW, Australia, 1998.
13. BHP. The Making of Iron and Steel, Seventh Edition, BHP Steel Group, Melbourne Vic, Australia, 1992.
14. American Society for Testing and Materials A611. Standard Specification for Steel, Sheet, Carbon, Cold-Rolled, Structural Quality, Philadelphia, PA, USA, 1994.
15. American Society for Testing and Materials A653. Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process, Philadelphia, PA, USA, 1994.
16. American Society for Testing and Materials A792. Standard Specification for Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process. Philadelphia, PA, USA, 1994.
17. European Committee for Standardisation, Eurocode 3. Design of steel structures, Part 1.3 General rules, Supplementary rules for cold formed thin gauge members and sheeting. Brussels, Belgium, 1996.
18. American Iron and Steel Institute. Changes to Specification and Commentary Sections C2, E2, E3.2, E3.3 and E5, Combined LRFD and ASD, Ballot C/S96-66D. Washington, DC, USA, 1998.
19. Cornell University. Tests on Bolted Connections - Third Progress Report. Unpublished Report for the AISI, 1954.
20. Cornell University. Tests on Bolted Connections - Fifth Progress Report. Unpublished Report for the AISI, 1954.
21. Cornell University. Tests on Bolted Connections - Sixth Progress Report. Unpublished Report for the AISI, 1954.
22. Cornell University. Tests on Bolted Connections - Seventh Progress Report. Unpublished Report for the AISI, 1956.
23. Winter G. Tests on bolted connections in light gage steel. Journal of the Structural Division, ASCE 1956;82(ST2):920-1-920-25.
24. Popowich DW. Tension capacity of bolted connections in light gage cold-formed steel. Thesis presented to the Graduate School of Cornell University for the Degree of Master of Science, School of Civil Engineering, 1969.
25. Rogers CA, Hancock GJ. Failure modes of bolted sheet steel connections loaded in shear. Research Report No. R772, Centre for Advanced Structural Engineering, Department of Civil Engineering, University of Sydney, Sydney, Australia, 1998.
26. European Convention for Constructional Steelwork, ECCS-TC7. The Design and Testing of Connections in Steel Sheeting and Sections, Publication No. 21, 1983.
27. American Institute of Steel Construction, Research Council on Structural Connections. Load and Resistance Factor Design - Specification for Structural Joints Using ASTM A325 or A490 Bolts. Chicago, IL, USA, 1988.
28. American Institute of Steel Construction. Specification for Structural Steel Buildings - Allowable Stress Design and Plastic Design. First Edition, Chicago, IL, USA, 1989.
29. American Institute of Steel Construction. Load and Resistance Factor Design - Specification for Structural Steel Buildings. Chicago, IL, USA, 1993.
30. American Society for Testing and Materials A370. Standard Test Methods and Definitions for Mechanical Testing of Steel Products. Philadelphia, PA, USA, 1994.
31. Zadanfarrokh F, Bryan ER. Testing and Design of Bolted Connections in Cold Formed Steel Sections. Proceedings of the 11th International Speciality Conference on Cold-Formed Steel Structures, University of Missouri-Rolla, Rolla, MO, USA, 1992:625-662.
32. Bryan E.R. The design of bolted joints in cold-formed steel sections. Thin-Walled Structures. 16:1993;239-262.
33. American Iron and Steel Institute. Commentary on the 1996 Edition of the Specification for the Design of Cold-Formed Steel Structural Members. Washington, DC, USA, 1997.
34. Standards Association of Australia. SAA Loading Code, Part 1: Dead and Live Loads and Load Combinations - AS 1170.1. Sydney, NSW, Australia, 1989.
35. Standards New Zealand. Code of Practice for General Structural Design and Design Loadings for Buildings - NZS 4203. Wellington, New Zealand, 1992.