Mechanistic force models for chip control tools

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 121, Issue 3, 1999, Pages 408-416

  Zhu, R ^a   Kapoor, S G ^a   DeVor, R E ^a   Athavale, S M ^b  

^a University of Illinois at Urbana Champaign   (United States)

^b FORD RESEARCH LABORATORY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EQUIPMENT TESTING; FORCE CONTROL; FORCE MEASUREMENT; FRICTION; GEOMETRY; INTERFACES (MATERIALS); INTERFACIAL ENERGY; MATHEMATICAL MODELS; MECHANICS;

CHIP CONTROL TOOLS; CUTTING TESTS; FLAT TOOLS; GROOVED TOOLS; MECHANISTIC FORCE MODELS; TOOL CHIP CONTACT;

MACHINE TOOLS;

EID: 0032598283     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.2832696     Document Type: Article

References (24)

1. Athavale, S. M., 1994, A Damage-based Model for Predicting Chip Breakability for Obstruction and Groove Tools, Ph. D. Thesis, N. C. State Univ., Raleigh, USA.
2. Chao, B. T., and Trigger, K. J., 1959, “Controlled Contact Cutting Tools,” Trans-actions of the ASME, Vol. 81, pp. 139-151.
3. DeVor, R. E., Chang, T. H., and Sutherland, J. W., 1992, Statistical Quality Design and Control, Macmillan (now Prentice-Hall).
4. Endres, W. J., DeVor, R. E., and Kapoor, S. G., 1995, “A Dual-Mechanism Approach to the Prediction of Machining Forces: Parts 1 and 2,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 117, pp. 526-541.
5. Fu, H. J., DeVor, R. E. and Kapoor, S. G., 1984, “A Mechanistic Model for the Prediction of the Force System in Face Milling Operations,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 106, pp. 81-88.
6. Jawahir, I. S., 1988, “The Too! Restricted Contact Effect as a Major Influencing Factor in Chip Breaking: An Experimental Analysis,” Annals of CIRP, Vol. 37/1, pp. 121-126.
7. Jawahir, I. S., and Van Luttervelt, C. A., 1993, “Recent Developments in Chip Control Research and Applications,” Annals of the CIRP, Vol. 42/2, pp. 659-693.
8. Jawahir, I. S., and Fang, X. D., 1995a, “A Knowledge-Based Approach for Designing Effective Grooved Chip Breakers—2D and 3D Chip Flow, Chip Curl and Chip Breaking,” Int. J. Adv. Manuf. Technol, Vol. 10, pp. 225-239.
9. Jawahir, I. S., and Zhang, J. P., 1995b, “An Analysis of Chip Curl Development, Chip Deformation And Chip Breaking in Orthogonal Machining,” Trans. ofNAMRI/SME, Vol. XXIII, pp. 109-114.
10. Kline, W. A., and DeVor, R. E., 1983, “The Effect of Runout on Cutting Geometry and Forces in End Milling,” Int. J. Mach. Tool Des. Res., Vol. 23, Nos. 2/3, pp. 123-140.
11. Loiadze, T. N., 1982, Prochnost I Iznosotojkost rechzushego intrumenta (Moscow, Mashinostroenie).
12. Nedess, C., and Hintze, W., 1989, “Characteristic Parameters of Chip Control in Turning Operations with Indexable Inserts and Three-dimensionally Shaped Chip Formers,” Annals of the CIRP, Vol. 38, No. 1, pp. 74-79.
13. Rubenstein, C., 1968, “The Mechanism of Orthogonal Cutting with Controlled Contact Tools,” Int. J. Mach. Tool Des. Res., Vol. 8, pp. 203-216.
14. Rubenstein, C., Venuvinod, P. K., and Lau, W. S., 1986, “Analysis of Oblique Cutting with Controlled Contact Tools,” Annals of the CIRP, Vol. 35, No. 1, pp. 51-54.
15. Sata, T., 1963, “Recent Development Concerning Cutting Mechanics,” Proc. Int. Prod. Engng Res. Conf., Pittsburgh, pp. 18-25.
16. Shi, T., and Ramalingam, S., 1991, “Slip-line Solution for Orthogonal Cutting with a Chip-breaker and Flank Wear,” Int. J. Mech. Sci., Vol. 33, No. 9, pp. 689-704.
17. Shi, T., and Ramalingam, S., 1993, “Modeling Chip Formation with Grooved Tools,” Int. J. Mech. Sci., Vol. 35, No. 9, pp. 741-756.
18. Strenkowski, J. S., and Athavale, S. M., 1997, “A Partially Constrained Eulerian Orthogonal Cutting Model for Chip Control Tools,” ASME JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING, Vol. 119, pp. 681-688.
19. Waldorf, D. J., 1996, Shearing, Ploughing, And Wear in Orthogonal Machining, Ph.D. Thesis, University of Illinois at Urbana-Champaign, Urbana, IL.
20. Worthington, B., and Redford, A. H., 1973, “Chip Curl and the Action of the Groove Type Chip Former,” Int. J. Mach. Tool Des. Res., Vol. 13, pp. 257-270.
21. Yang, J. A., 1992, A Predictive Model of Chip Breaking for Groove-type Tools in Orthogonal Machining of AISI 1020 Steel, Ph.D. Thesis, North Carolina State University, Raleigh, NC.
22. Zhang, B., and Bagchi, A., 1994, “Finite Element Simulations of Chip Formation and Comparison with Machining Experiment,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 116, pp. 289-297.
23. Zhu, R., 1997, Mechanistic Force Model for Grooved Tools in Orthogonal Machining, M.S. Thesis, University of Illinois at Urbana-Champaign, Urbana, IL.
24. Zorev, N. N., 1963, “Interrelation Between Shear Processes Occurring Along Tool Face and on Shear Plane in Metal Cutting,” Proc. Int. Prod. Engng Res. Conf, Pittsburgh, pp. 42-49.