A partially constrained eulerian orthogonal cutting model for chip control tools

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 119, Issue 4B, 1997, Pages 681-688

  Strenkowski, J S ^a   Athavale, S M ^a  

^a North Carolina State University   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 12344272784     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.2836809     Document Type: Article

References (48)

1. Agrawal, A., and Dawson, P. R., 1985, “A Comparison of Galerkin and Streamline Techniques for Integrating Strains from an Eulerian Flow Field,” Int. J. for Numerical Methods in Eng., Vo. 21, p. 853.
2. Altan, T., and Boulger, F. W., 1973, “Flow Stress of Metals and Its Application in Metal Forming Analyses,” ASME Journal of Engineering for Industry, Vol. 95, p. 1009.
3. Athavale, S. M., 1994, “A Damage-Based Model for Predicting Chip Break- ability for Obstruction and Groove Tools,” PhD Dissertation, North Carolina State University.
4. Athavale, S. M., and Strenkowski, J. S., 1995, “Material Damage Based Model For Predicting Chip-Breakability,” Proc. Of ASME IMECE, MED-Vol. 2-1/MH- Vol. 3-1. p. 303, also to appear in Journal of Manufacturing Science and Engineering, 1997.
5. Boothroyd, G., and Bailey, J. A., 1966, “A Laboratory Course in Metal Cutting,” Bulletin of Mechanical Engineering in Education, Vol. 5, p. 3.
6. Camacho, G., Marusich, T., and Ortiz, M., 1993, “Adaptive Meshing Methods for the Analysis of Unconstrained Plastic Flow,” Advanced Computational Methods for Material Modeling, Benson, D. J. and Asaro, R. J., eds., ASME AMD- Vol. 180/PVP-Vol. 268, pp. 71-83.
7. Carroll, J. T., 1986, “A Numerical and Experimental Study of Single Point Diamond Machining,” PhD Dissertation, North Carolina State University.
8. Carroll, J. T., and Strenkowski, J. S., 1988, “Finite Element Models of Orthogonal Cutting with Application to Single Point Diamond Turning,” International Journal of Mechanical Sciences, Vol. 30, pp. 899-920.
9. Dawson, P. H., 1987, “Viscoplastic Finite Element Analysis of Steady State Forming Processes Including Strain History and Stress Flux Dependence,” ASME, AMD, 28, p. 55.
10. Dewhurst, P., 1979, “The Effect of Chip Breaker Constraints on Mechanics of Machining,” Annals of CIRP, Vol. 28, pp. 1-5.
11. Ernst, H., and Merchant, M. E., 1941, “Chip Formation, Friction and High Quality Machined Surfaces,” Surface Treatment of Metals, Vol. 29, p. 299.
12. Hsu, J. M., 1990, “Three-Dimensional Finite Element Modeling of Metal Cutting,” PhD Dissertation, 1990, North Carolina State University.
13. Hsu, H. C., 1992, “An Elasto-Viscoplastic Finite Element Model of Orthogonal Metal Cutting for Residual Stress Prediction,” PhD Dissertation, North Carolina State University.
14. Johnson, W., 1962, “Some. Slip-Line Fields for Swaging or Expanding, Indenting, Extruding and Machining with Curved Dies,” International Journal of Mechanical Sciences, Vol. 4, p. 323.
15. Klamecki, B. E., 1973, “Incipient Chip Formation in Metal Cutting—A Three Dimension Finite Element Analysis,” PhD Dissertation, University of Illinois at Urbana-Champaign.
16. Kudo, H., 1965, “Some New Slip-Line Solutions for Two-Dimensional Steady- State Machining,” International Journal of Mechanical Sciences, Vol. 7, p. 43.
17. Lajczok, M. R., 1980, “A Study of Some Aspects of Metal Machining Using Finite Element Method,” PhD Dissertation, North Carolina State University.
18. Lee, E. H., and Schaffer, B. W., 1951, “The Theory of Plasticity Applied to a Problem of Machining,” ASME Journal of Applied Mechanics, Vol. 18, No. 4, p. 405.
19. Malkus, D. S., and Hughes, T. J. R., 1978, “Mixed Finite Element Methods— Reduced and Selective Integration Techniques: A Unification of Concepts,” Computer Methods in Applied Mechanics and Engineering, Vol. 15, p. 63.
20. Manyindo, B. M., and Oxley, P. L. B., 1986, “Modelling the Catastrophic Shear type of Chip when Machining Stainless Steel,” Proceedings of Institute of Mechanical Engineers, Vol. 200, No. 5, p. 349.
21. Merchant, M. E., 1945, “Mechanics of the Cutting Process,” Journal of Applied Physics, Vol. 16, p. 267.
22. Natarajan, R., and Jeelani, S., 1983, “Residual Stresses in Machining Using Finite Element Method,” Computers in Engineering, Computer Software and Applications, Vol. 3, p. 79.
23. Niebauer, K., 1993, Kennametal, Inc., Private Communication.
24. Okushima, K., and Kakino, Y., 1971, “The Residual Stress Produced by Metal Cutting,” Annals of CIRP, Vol. 20, No. 1, p. 13.
25. Oxley, P. L. B., 1961, “A Strain Hardening Solution for the Shear Angle in Orthogonal Metal Cutting,” International Journal of Mechanical Sciences, Vol. 3, p. 68.
26. Oxley, P. L. B., and Hatton, A. P., 1963a, “Shear Angle Solution Based on Experimental Shear Zone and Tool-Chip Interface Stress Distribution,” International Journal of Mechanical Sciences, Vol. 5, p. 41.
27. Oxley, P. L. B., and Welsh, M. J. M., 1963b, “Calculating the Shear Angle in Orthogonal Metal Cutting from Fundamental Stress, Strain, Strain-Rate Properties of the Work Material,” Proceedings 4th International Machine Tool Design and Research Conference. Pergamon, Oxford, p. 73.
28. Palmer, W. B., and Oxley, P. L. B., 1959, “Mechanics of Metal Cutting,” Proceedings of Institute of Mechanical Engineers, Vol. 173, p. 623.
29. Piispanen, V., 1937, “Lastunmoudostimisen Teoriaa,” Teknillinen Aika Kaus- lehti, Vol. 27, p. 315.
30. Sani, R. L., Gresho, P. M., Lee, R. L., and Griffiths, D. F., 1981, “The Cause and Cure (?) of the Spurious Pressure Generated by Certain FEM Solutions of the Incompressible Navier-Stokes Equations: Part I,” International Journal of Numerical Methods in Fluids, Vol. 1, p. 17.
31. Shih, A. J., 1993, “Finite Element Analysis of The Rake Angle Effects in Orthogonal Cutting,” Proc., ASME Sym. on Modeling, Monitoring and Control Issues in Manufac., PED-Vol. 64, pp. 475-483.
32. Shih, T., and Ramalingam, S., 1993, “Modeling Chip Formation with Groove Tools,” International Journal of Mechanical Sciences, Vol. 33, No. 9, p. 741.
33. Shih, T., and Ramalingam, S., 1991, “Slip-Line Solution for Orthogonal Cutting with a Chip Breaker and Flank Wear,” International Journal of Mechanical Sciences, Vol. 35, No. 9, p. 689.
34. Shirakashi, T., and Usui, E., 1974, “Simulation of Orthogonal Cutting Mechanism,” Proceedings of International Conference of Production Engineering, Tokyo, p. 535.
35. Strenkowski, J. S., and Carroll, J. T., 1986, “An Orthogonal Metal Cutting Model Based on an Eulerian Finite Element Method,” Manufacturing Processes, Machines and Systems, Proceedings of the 13th NSF Conference on Production Research and Technology.
36. Strenkowski, J. S., and Mitchum, G. L., 1987, “An Improved Finite Element Model of Orthogonal Metal Cutting,” Proceedings of North America Manufacturers Research Conference, Bethlehem, PA, p. 505.
37. Strenkowski, J. S., and Moon, K. J., 1990, “Finite Element Prediction of Chip Geometry and Tool/Workpiece Temperature Distributions in Orthogonal Cutting,” ASME Journal of Engineering for Industry, Vol. 112, p. 313-318.
38. Trent, E. M., 1988, “Metal Cutting and the Tribology of Seizure: II Movement of Work Material Over the Tool in Metal Cutting,” Wear, Vol. 128, p. 47.
39. Usui, E., and Hoshi, K., 1963, “Slip-Line Fields in Metal Cutting Involving Centered Fan Fields,” International Research in Production Engineering ASME, p. 61.
40. Usui, E., and Shirakashi, T., 1982, “Mechanics of Machining from Descriptive to Predictive Theory,” On the Art of Cutting Metals—75 Years Later, ASME Publication PED, 7, p. 13.
41. Wayne, S. F., Zimmerman, C., and ONiel, D. A., 1993, “Aspects of Advanced Cutting Tool and Chip-Flow Modeling,” Proceedings of the 13th International Plansee Seminar, H. Bildstein and R. Eck, eds. Metallwerk Plansee, Reutte Vol. 2, p. 64.
42. Worthington, B., and Redford, A. H., 1973, “Chip Curl and the Action of the Groove Type Chip Form,” International Journal of Machine Tool Design and Research, Vol. 13, p. 257.
43. Worthington, B., 1976, “The Effect of Rake Face Configuration on the Curvature of the Chip in Metal Cutting,” International Journal of Machine Tool Design and Research, Vol. 15, p. 223.
44. Worthington, B., and Rahman, M. H., 1979, “Predicting Breaking with Groove Type Breakers,” International Journal of Machine Tool Design and Research, Vol. 19, p. 121.
45. Yang J. A., 1992, “A Predictive Model of Chip Breaking for Groove-Type Tools in Orthogonal Machining of AISI 1020 Steel,” PhD Dissertation, North Carolina State University.
46. Zhang, B., and Bagchi, A., 1994, “A Study of Chip Separation and its Approximation in Finite Element Simulation of Continuous Chip Formation,” Proc. Of Winter Annual Meeting of the ASME, Material Issues in Machining II and Physics of Machining Processes II, D. A. Stephenson and R. Stevenson, eds., p. 157.
47. Zienkiewicz, O. C., Taylor, R. L., and Too, J. M., 1971, “Reduced Integration Technique in General Analysis of Plate and Shell,” International Journal of Numerical Methods in Engineering, Vol. 3, p. 275.
48. Zienkiewicz, O. C., Jain, P. C., and Onate, E., 1978, “Flow of Solids during Forming and Extrusion: Some Aspects of Numerical Solutions,” International Journal of Solids and Structures, Vol. 14, pp. 15-38.