The effect of the packing parameters, gate geometry, and mold elasticity on the final dimensions of a molded part

Polymer Engineering and Science

Volumn 36, Issue 15, 1996, Pages 1961-1971

  Leo, V ^a   Cuvelliez, Ch ^a,b  

^a SOLVAY S A   (Belgium)

^b AVN   (Belgium)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTER SIMULATION; ELASTICITY; HIGH DENSITY POLYETHYLENES; MOLDS; PRESSURE EFFECTS; RESIDUAL STRESSES; SHRINKAGE;

CAVITY PRESSURE TIME HISTORY; FINAL MOLDED PART DIMENSIONS; GATE GEOMETRY; MOLD ELASTICITY; PACKING PARAMETERS; TIME DEPENDENT PRESSURE DISTRIBUTION;

PLASTICS MOLDING;

EID: 0030211385     PISSN: 00323888     EISSN: None     Source Type: Journal    
DOI: 10.1002/pen.10592     Document Type: Article

References (23)

1. V. Leo and Ch. Cuvelliez in Injection Moulding of Thermoplastics: Practical Use of Numerical Simulation, TI KVIV Seminar, Antwerp, Belgium (April 1994).
2. T. S. Chung, J. Polym. Eng., 8, 175 (1988).
3. H. H. Chiang, C. A. Hieber, and K. K. Wang, Polym. Eng. Sci., 31, 116 (1991).
4. C. A. Hieber, G. Vandenengel, and H. H. Chiang, SPE ANTEC Tech. Papers, 32, 181 (1986).
5. D. C. Paulson, SPE ANTEC Tech. Papers, 16, 435 (1970).
6. J. Greener, SPE ANTEC Tech. Papers, 31, 822 (1985).
7. B. Miller, Plast. World, 49, No 10,20 (9/1991).
8. A. Cui, M. Konno, N. Nishiwaki, S. Hori, and M. Inoue, Polym. Process. Soc. Annual Meeting 9, Manchester, Britain (1993).
9. A. A. Flaman, Polym. Eng. Sci., 33, 193 (1993).
10. A. A. Flaman, Polym. Eng. Sci., 33, 202 (1993).
11. K. M. M. Jansen, Intern. Polym. Proc., IX, 1, 82 (1994).
12. Ch. Cuvelliez, V. Leo, C. Friedl, and P. Kennedy, SPE ANTEC Tech. Papers, 39, 1618 (1993).
13. H. Recker and G. Menges, SPE ANTEC Tech. Papers, 28, 327 (1982).
14. C. L. Thomas, A. A. Tseng, A. J. Bur, and J. L. Rose, SPE ANTEC Tech. Papers, 39, 143 (1993).
15. J. P. Trotignon and J. Verdu, J. Appl. Polym. Sci., 34, 1 (1987).
16. Injection and Compression Molding Fundamentals, A. I. Isayev, ed., Marcel Dekker (1987).
17. P. Thienel, Th. Droste, and A. Kruse, Kunststoffe, 83, 4, 283 (1993).
18. R. Wimberger-Friedl and J. G. De Bruyn, Polym. Eng. Sci., 33, 383 (1993).
19. V. Leo, in "Flow and Cure of Polymers: Measurements and Control," RAPRA Seminar, Telford, U.K. (March 1990).
20. M. Saiu, V. Brucato, S. Piccarolo, and G. Titomanlio, Intern. Polym. Proc. VII, 3, (1992).
21. Kistler technical brochure, Piezo Instrumentation, Measuring Instruments for Plastic Processing (1993).
22. C. J. Yu, J. E. Sunderland, and C. Poli, Polym. Eng. Sci., 30, 1599 (1990).
23. G. Titomanlio and S. Piccarolo, J. Appl. Polym. Sci., 35, 1483 (1988).