Tool wear and surface integrity during high-speed turning of hardened steel with polycrystalline cubic boron nitride tools

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture

Volumn 215, Issue 6, 2001, Pages 755-767

  Kishawy, H A ^a   Elbestawi, M A ^a  

^a MCMASTER UNIVERSITY   (Canada)

Author keywords

Hard turning; Polycrystalline cubic boron nitride (PCBN) tools; Residual stresses; Surface integrity; Tool wear

Indexed keywords

EID: 0012827656     PISSN: 09544054     EISSN: None     Source Type: Journal    
DOI: 10.1243/0954405011518700     Document Type: Article

References (26)

1. Abrão, A. M., Aspinwall, D. K. and Wise, M. L. H. Tool wear, cutting forces and temperature evaluation when turning hardened bearing steel using PCBN and ceramic tool materials. In Matador International Conference, 1995, pp. 209-216.
2. Smith, G. T. Advanced Machining. The Handbook of Cutting Technology, 1989 (IFS Publications, Bedford).
3. Kloss, K. H. and Kaiser, B. Residual Stresses induced by Manufacturing, 1990, pp. 205-226 (Association for Heat Treatment and Materials Technology and German Society for Material Science and Technology).
4. Matsumoto, Y., Barash, M. M. and Liu, C. R. Effect of hardness on the surface integrity of AISI 4340 steel. Trans. ASME, J. Engng for Industry, 1986, 108(3), 169-175.
5. Field, M. and Kahles, F. J. Review of surface integrity of machined components. Ann. CIRP, 1971, 20, 107-108.
6. Liu, C. R. and Barash, M. M. Variables governing patterns of mechanical residual stress in a machined surface. Trans. ASME, J. Engng for Industry, 1982, 104(3), 257-264.
7. Sadat, A. B. and Bailey, J. A. Residual stresses in turned AISI 4340 steel. Expl Mechanics, March 1987, 27(1), 80-85.
8. Schreiber, E. and Schlicht, H. Residual stresses after turning of hardened components. In International Conference on Residual Stresses, Garmisch-Partenkirchen, FRG, 1986, pp. 853-860.
9. Sadat, A. B. Effect of high speed on surface integrity of AISI 4340 steel during turning. Mater. Sci. Technol., 1990, 6, 371-375.
10. Tönshoff, H. K., Wobker, H. G. and Brandt, D. Tribological aspects of hard turning with ceramic tools. J. Soc. Tribologists Lubric. Engrs, 1995, 51(2), 163-168.
11. Tönshoff, H. K., Wobker, H. G. and Brandt, D. Hard turning - influences on the workpiece properties, Trans. NAMRI/SME, 1995, 23, 215-220.
12. Abrão, A. M., Wise, M. L. H. and Aspinwall, D. K. Tool life and workpiece surface integrity evaluations when machining hardened AISI H13 and AISI E52100 steels with conventional ceramic and PCNB tool materials. In Twenty-Third NAMRC Conference, MR95-195, 1995, pp. 1-9.
13. Field, M., Koster, W. P., Kohls, J. B., Snider, R. E. and Maranchic, J. Machining of high strength steels with emphasis on surface integrity. Technical Report AFML-TR-70-11, Air Force Material Laboratory, MATF, Wright-Patterson Air Force Base, Ohio, 1970.
14. Poggie, R. A. and Wert, J. J. The influence of surface finish and strain hardening on near surface residual stress and the friction and wear behaviour of A2, D2 and CPM-10V tool steels. Wear, 1991, 149, 209-220.
15. El-Wardany, T. I., Kishawy, H. A. and Elbestawi, M. A. Surface integrity of die material in high speed hard machining: Part II, microhardness variations and residual stresses. Trans. ASME, J. Mfg Sci. Engng, 2000, 122(4), 632-641.
16. Kishawy, H. A. and Elbestawi, M. A. Effect of edge preparation and cutting speed on surface integrity of die material in high speed machining. In International Mechanical Engineering Congress and Exposition, ASME Annual Winter Meeting, California, 14-19 November 1998, pp. 269-276.
17. Prevey, P. S. A method of determining the elastic properties of alloys in selected crystallographic directions for X-ray diffraction residual stress measurement. Adv. X-Ray Anal., 1986, 20, 345-354.
18. Koistinen, D. P. and Maburger, R. E. A simplified procedure for calculating peak position in X-ray residual stress measurements on hardened steel. Trans. ASME, 1959, 51, 537-550.
19. Moore, M. G. and Evans, W. P. Mathematical correction for stress in removal layers in X-ray diffraction residual stress analysis. Trans. ASME, 1958, 66, 340-345.
20. Bailey, J. A., Jeelani, S. and Becker, S. E. Surface integrity in machining AISI 4340 steel. Trans. ASME, J. Engng for Industry, 1976, 98, 999-1006.
21. Bresseler, B., El-Wardany, T. I. and Elbestawi, M. A. Material side flow in high speed finish boring of case hardened steel. In First French and German Conference on High Speed Machining, 1997, pp. 196-206.
22. Warnecke, G. and Bach, P. Mechanical and material influences on machined surface in precision turning of steel with ceramics. In Proceedings of the Sixteenth North American Research Conference, 1988, pp. 209-216.
23. Kishawy, H. A. and Elbestawi, M. A. Effect of process parameters on material side flow during hard turning. Int. J. Mach. Tool Mf., 1999, 39(5), 1017-1030.
24. Roberts, G. A., Hamaker Jr, J. C. and Johnson, A. R. Tool Steels, 3rd edition, 1962 (American Society for Metals, Metals Park, Ohio).
25. Gill, J. P., Rose, R. S., Roberts, G. A., Johnstin, H. G. and George, R. B. Tool Steels, 1944 (American Society for Metals, Cleveland, Ohio).
26. El-Wardany, T. I., Mohammed, E. and Elbestawi, M. A. Cutting temperature of ceramic tools in high speed machining of difficult-to-cut materials. Int. J. Mach. Tools Mf., 1996, 36(5), 611-634.