EFFECTS OF EDGE PREPARATION AND CUTTING SPEED ON SURFACE INTEGRITY OF DIE MATERIALS IN HARD MACHINING

ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE)

Volumn 1998-R, Issue , 1998, Pages 269-276

  Kishawy, Hossam A ^a   Elbestawi, Mohamed A ^a  

^a MCMASTER UNIVERSITY   (Canada)

Author keywords

[No Author keywords available]

Indexed keywords

CUTTING TOOLS; GAS TURBINES; RESIDUAL STRESSES; SCANNING ELECTRON MICROSCOPY; TOOL STEEL; WEAR OF MATERIALS; X RAY DIFFRACTION;

CUTTING CONDITIONS; CUTTING SPEED; D2 TOOL STEELS; DIE MATERIALS; EDGE CUTTINGS; EDGE PREPARATION; HARD MACHINING; MACHINED SURFACE; SURFACE INTEGRITY; TOOL WEAR;

CUTTING;

EID: 85124367939     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/IMECE1998-1038     Document Type: Conference Paper

References (23)

1. Abrdo. A. M.. Wise, M. L. H., and Aspinwall. D. K.. 1995, 'Tool Life and Workpiece Surface Integrity Evaluations When Machining Hardened AISI H13 and AISI E52KX) Steels With Conventional Ceramic and PCBN Tool Materials,” NAMRC XXIII Conference, May 24-26, Houghton, Michigan. MR95-195. pp. 1-9.
2. Bresscler, B..E1-Wardany, T. I., and Elbestawi, M. A., 1997, "Material Side Flow in High Speed Finish Boring of Case Hardened Steel,” lsl French and German Conference on High Speed Machining, pp. 196-206.
3. Elbestawi, M. A., Chen, L., Becze, C. E., and El-Wardany, T. I., 1997. “High Speed Milling of Dies and Moulds in their Hardened State.” Annals of the CIRP Vol. 46, pp. 57-62.
4. El-Wardany, T.I., Mohammed, E., and Elbestawi, M. A., 1996, “Cutting Temperature of Ceramic Tools in High Speed Machining of Difficult-To-Cut Materials.” Int. J. Mach. Tools Manufact.. Vol. 36, No. 5, pp. 611-634.
5. Field, M.. and Kahles, J., 1971. “Review of Surface Integrity of Machined Components.” Annals of the CIRP Vol. 20/2, pp. 153-163.
6. Field, M.. Koster. W. P., Kohls, J. B.. Snider. R. E.. and Maranchic. J., 1970, “Machining of High Strength Steels With Emphasis on Surface Integrity,” Technical Report AFML-TR-70-11, Air Force Material Laboratory, MATF, Wright-Patterson Air Force Base, Ohio, U.S.A.
7. Gill, J. P., Rose, R., S., Roberts, G. A., Johnstin. H.G. and George, R. B., 1944, 'Tool Steels,” The American Society for Metals, Cleveland, Ohio.
8. Ikeda, T., Takahashi, I., Matsuoka, T., and Nakagawa, T., 1992, “Ultra High Speed Milling of Die Steel with Ball-nose End Mill,” Proc. 2nd Int. Conf. On Die and Mould Technology, Singapore, Sept., pp 48-56.
9. Kloss. K. H., and Kaiser, B., 1990, “Residual Stresses Induced by Manufacturing,” Association for Heat Treatment and Materials Technology and German Society for Material Science and Technology, pp. 205-226.
10. Koistinen. D. P. and Maburger. R. E., 1959. “A Simplified Procedure for Calculating Peak Position in X-Ray Residual Stress Measurements on Hardened Steel,"Transactions of the ASME, Vol. 51. pp. 537-550.
11. Liu, C. R., and Barash, M. M.. 1982, “Variables Governing Patterns of Mechanical Residual Stress in a Machined Surface,” Transactions of the ASME, Journal of Engineering for Industry, Vol. 104/3, pp. 257-264.
12. Matsumoto, Y., Barash, M. M.. and Liu, C. R..1986, “Effect of Hardness on the Surface Integrity of AISI 4340 Steel,” Transactions of the ASME. Journal of Engineering for Industry. Vol. 108/3, pp. 169-175.
13. Moore. M. G. and Evans, W. P., 1958, “MathematicalCorrectionfor Stress in Removal Layers in X-Ray Diffraction Residual Stress Analysis,’’Transactions of the ASME, Vol. 66, pp. 340-345.
14. Roberts, G. A.. Hamakcr. Jr., J. C. and Johnson, A. R.. 1962, 'Tool Steels,” The American Society for Metals, 3^ E Pekelharing, A. J. and Gieszen, C. A., 19 Finish Turning,” Annals of the C1RP, Vol. 20,
15. Poggie. R. A. and Wert, J. J., 1991, “Th and Strain Hardening on Near Surface Res and Wear Behaviour of A2, D2 and CPM-Materials, ASME, pp. 497-501.
16. Prevey, P. S., 1986, “A Method of Deter Properties of Alloys in Selected Crystallographic F Diffraction Residual Stress Measurement,” Adv. In X-pp. 345-354.
17. Righy, P., 1993, “High Speed Milling in the Moul Industries,” Diamond and CBN Ultra Hard Material Ontario, Canada.
18. Sadat, A. B., 1990, “Effect of High Speed on S AISI4340 Steel During Turning,” Material Science and 6, pp. 371-375.
19. Sadat, A. B., and Bailey, J. A., 1987,“Residual St 4340 Steel,” Experimental Mechanics, Vol. 27, No. 1
20. Schreiber, E., and Schlicht, H., 1986,’’Res Turning of Hardened Components,” The Internat Residual Stresses, Garnish - Partenkirchen (FRG),
21. Tonshoff, H. K., Wobkcr, H. G., and Brandt, D “Tribological Aspects of Hard Turning with Ceramic Tools,” the Society ofTribologists and Lubrication Engineers, Vol. 51/ 168.
22. Tonshoff, H. K., Wobkcr, H. G., and Brandt, D., Turning - Influences on the Workpiece Properties,” T NAMR1/SME, Vol. XXIII, pp. 215-220.
23. Warnecke, G. and Bach, P., 1988. “Mechanical an Influences on Machined Surface in Precision Turning of Ceramics,” Proceeding of the 16“’ North American Research C pp. 209-216.