MATERIAL CONSTITUTIVE MODELING UNDER HIGH STRAIN RATES AND TEMPERATURES THROUGH ORTHOGONAL MACHINING TESTS

ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE)

Volumn 1997-W, Issue , 1997, Pages 91-98

  Lei, Shuting ^a   Shin, Yung C ^a   Incropera, Frank P ^a  

^a PURDUE UNIVERSITY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CONSTITUTIVE MODELS; GRAIN BOUNDARIES; INFRARED IMAGING; MACHINING; SHEAR STRESS; STRAIN RATE;

DEFORMATION BEHAVIOR; ENGINEERING MATERIALS; HIGH-STRAIN-RATE; MACHINING PROCESS; MACHINING TEST; MATERIAL CONSTITUTIVE MODELS; ORTHOGONAL MACHINING; SHEAR ZONE; STRAIN-TEMPERATURE; STRESS/STRAIN;

LOW CARBON STEEL;

EID: 0004524698     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/IMECE1997-1140     Document Type: Conference Paper

References (23)

1. Carroll, J.T., III and Strenkowski, J.S., 1988, " Finite Element Models of Orthogonal Cutting with Application to single Point Diamond Turning", Int. J. Meeh. Sci., Vol. 30, pp. 899-920.
2. Chao, B.T., and Bisacre, G.H., 1951, "The Effect of Speed and Feed on Mechanics of Metal Cutting", Proc. Instn. Meeh. Engrs., Vol. 165, PP- 1-
3. Goriani, V.L., and Kobayashi, S., 1967, "Strain and Strain-Rate Distributions in Orthogonal Metal Cutting", Annals of the CIRP, Vol. 15, pp. 425-431.
4. Haque, M.M. and Hashmi, M.S.J., 1984, "Stress-Strain Properties of Structural Steel at Strain Rates of up to lO’ per Second at Sub-zero, Room and High Temperature", Mechanics of Materials, Vol. 3, pp. 245.
5. Hashmi, M.S.J. and Hamouda, A.M.S., 1994, "Development of a One-Dimensional Constitutive Equation for Metals Subjected to High Strain Rate and Large Strain", Journal of Strain Analysis, Vol. 29, No. 2,pp. 117-127.
6. Joshi, V.S., Dixit, P.M. and Jain, V.K., 1994, "Viscoplastic Analysis of Metal Cutting by Finite Element Method", Int. J. Mach. Tools Manufact., Vol. 34, No. 4, pp. 553-571.
7. Kececioglu, D., 1958, "Shear Strain Rate in Metal Cutting and Its Effects on Shear-Flow Stress", Trans. ASME, Vol. 80, pp. 158-168.
8. Kim, K.W. and Sin, H., 1996, "Development of A ThermoViscoplastic Cutting Model Using Finite Element Method", Int. J. Mach. Tools Manufact., Vol. 36, No. 3, pp. 379-397.
9. Klopp, R.W., Clifton, R.J. and Shawki, T.G., 1985, "Pressure-Shear Impact and the Dynamic Viscoplastic Response of Metals", Mechanics of Materials, Vol. 4, pp. 375-385.
10. Komvopoulos, K., and Erpenbeck, S.A., 1991, " Finite Element Modeling of Orthogonal Metal Cutting", ASME Journal of Engineering for Industry, Vol. 113, pp. 253-267.
11. Novak, J.W., 1995, Plasma Enhanced Machining of Difficult to Manufacture Materials, M.S. Thesis, Purdue University.
12. Oxley, P.L.B., 1989, The Mechanics of Machining; An Analytical Approach to Assessing Machinability, Halsted Press.
13. Russell, J.K., and Brown, R.H., 1965, "Deformation During Chip Formation", Journal of Engineering for Industry, Vol. 87, pp. 53-56.
14. Scrutton, R.F., 1968, "The Geometry of the Shear Zone in Metal Cutting", Trans. ASME, Journal of Engineering for Industry, Vol. 90, pp. 420-424.
15. Shaw, M.C., 1984, Metal Cutting Principles, Oxford University Press, Oxford, Chapter 12.
16. Shaw, M.C., 1950, "A Quantized Effect of Strain Hardening as Applied to Cutting of Metal", J. Appl. Phys. Vol. 21, pp.599.
17. Shih, A.J., 1995, "Finite Element Simulation of Orthogonal Metal Cutting", ASME Journal of Engineering for Industry, Vol. 117, pp. 84-92.
18. Stephenson, D.A., 1991, "An Inverse Method for Investigating Deformation Zone Temperatures in Metal Cutting", ASME Journal of Engineering for Industry, Vol. 113, pp. 129-136.
19. Stevenson, M.G., and Oxley, P.L.B., 1973, "High Temperature Stress-Strain Properties of A Low-Carbon Steel from Hot Machining Tests", Proc. Instn. Meeh. Engrs., Vol. 187, pp. 263-272.
20. Stevenson, M.G., and Oxley, P.L.B., 1969-70, "An Experimental Investigation of the Influence of Speed and Scale on the Strain-Rate in a Zone of Intense Plastic Deformation", Proc. Instn. Meeh. Engrs., Vol. 184, No. 31, pp. 561-575.
21. Tay, A.O., Stevenson, M.G., de Vahl Davis, G., and Oxley, P.L.B., 1976, "A Numerical Method for Calculating Temperature Distributions in Machining, from Force and Shear angle Measurements", Int. J. MTDR, Vol. 16, pp. 335-349.
22. Usui,E., Hirota,A., 1978, "Analytical Prediction of Three Dimensional Cutting Process, Part 1: Basic Cutting Model and Energy Approach, Part 2: Chip Formation and Cutting Force with Conventional Single Point Tool", Trans. ASME 100, pp. 222-235.
23. Wang, L., Saito, K., and Jawahir, S., 1996, "Infrared Temperature Measurement of Curled Chip Formation in Machining", Trans, of NAMRI/SME, Vol. 24, pp. 87-92.