Development of a thermo-viscoplastic cutting model using finite element method

International Journal of Machine Tools and Manufacture

Volumn 36, Issue 3, 1996, Pages 379-397

  Kim, Kug Weon ^a   Sin, Hyo Chol ^a  

^a Seoul National University   (South Korea)

Author keywords

[No Author keywords available]

Indexed keywords

CALCULATIONS; CARBON STEEL; FINITE ELEMENT METHOD; FORCE MEASUREMENT; FRICTION; HEAT TRANSFER COEFFICIENTS; MATHEMATICAL MODELS; MECHANICS; OSCILLATIONS; STRESSES; TEMPERATURE DISTRIBUTION; THERMAL EFFECTS;

CHIP TOOL CONTACT LENGTH; FREE CHIP GEOMETRY; STEADY STATE ORTHOGONAL CUTTING; THERMOVISCOPLASTIC CUTTING MODEL;

METAL CUTTING;

EID: 0030107637     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/0890-6955(95)00054-2     Document Type: Article

References (18)

1. M. R. Lajczok, A study of some aspects of metal machining using the finite element method, Ph.D. Dissertation, North Carolina State University (1980).
2. E. Usui and T. Shirakashi, Mechanics of machining - From descriptive to predictive theory, The Art of Cutting Metals - 75 Years Later (a tribute to F. W. Taylor), ASME Publication PED - Vol. 7, pp. 13-35 (1982).
3. K. Iwata, K. Osakada and Y. Terasaka, Process modeling of orthogonal cutting by the rigid-plastic finite element method, Trans. ASME J. Engng Mater. Technol. 106, 132-138 (1984).
4. J. S. Strenkowski and J. T. Carroll, III, A finite element method of orthogonal metal cutting, Trans. ASME J. Engng Ind. 107, 346-354 (1985).
5. J. S. Strenkowski and G. L. Mitchum, An improved finite element model of orthogonal metal cutting, Proc. North American Mfg Res. Conf., Bethlehem, PA, pp. 506-509 (1987).
6. Z. C. Lin and S. Y. Lin, A coupled finite element model of thermal-elastic-plastic large deformation for orthogonal cutting, Trans. ASME J. Engng Ind. 114, 218-226 (1992).
7. J. S. Strenkowski and J. T. Carroll, III, An orthogonal metal cutting model based on an eulerian finite element method, Proc. 13th NSF Conf. on Prod. Res. Technol., pp. 261-264 (1986).
8. J. S. Strenkowski and K. J. Moon, Finite element prediction of chip geometry and tool-workpiece temperature distributions in orthogonal metal cutting, Trans. ASME J. Engng Ind. 112, 313-318 (1990).
9. T. Moriwaki, N. Sugimura and S. Luan, Combined stress, material flow and heat analysis of orthogonal micromachining of copper, Ann. CIRP 42, 75-78 (1993).
10. P. L. B. Oxley and W. F. Hastings, Minimum work as a possible criterion for determining the frictional conditions at the tool-chip interface in machining, Phil. Trans. R. Soc. Lond. 282, 565-584 (1976).
11. M. Oyane, F. Takashima, K. Osakada and H. Tanaka, The behaviour of some steels under dynamic compression, Proc. 10th Japan Congress on Testing Materials, pp. 72-76 (1967).
12. P. L. B. Oxley, Mechanics of Machining: An Analytical Approach to Assessing Machinability. Ellis Horwood, Chichester (1989).
13. J. C. Heinrich, P. S. Huyakorn and O. C. Zienkiewicz, An 'upwind' finite element scheme for two-dimensional convective transport equation, Int. J. Numer. Meth. Engng 11, 131-143 (1977).
14. O. C. Zienkiewicz, P. C. Jain and E. Onate, Flow of solids during forming and extrusion: some aspects of numerical solutions, Int. J. Solids Structures 14, 15-38 (1978).
15. B. Peter, More on infinite elements, Int. J. Numer. Meth. Engng 15, 1613-1626 (1980).
16. M. G. Stevenson and P. L. B. Oxley, An experimental investigation of the influence of speed and scale on the strain-rate in a zone of intense plastic deformation, Proc. Instn. Mech. Engrs 184, 561-576 (1969/1970).
17. A. O. Tay, M. G. Stevenson and G. Davis, Using the finite element method to determine temperature distributions in orthogonal machining, Proc. Instn. Mech. Engrs 188, 627-638 (1974).
18. A. O. Tay, M. G. Stevenson, G. Davis and P. L. B. Oxley, A numerical method for calculating temperature distributions in machining from force and shear angle measurements, Int. J. Mach. Tool Des. Res. 16, 335-349 (1976).