A study on a metal pushing V-belt type CVT - A novel approach to characterize the friction between blocks and a pulley, and shifting mechanisms

SAE Technical Papers

Volumn , Issue , 2002, Pages

  Kataoka, Ryuhei ^a   Okubo, Kazuya ^a   Fujii, Toru ^a   Kanehara, Shigeru ^b  

^a DOSHISHA UNIVERSITY   (Japan)

^b HONDA R AND D CO LTD   (Japan)

Author keywords

[No Author keywords available]

Indexed keywords

PULLEYS; TRIBOLOGY; VARIABLE SPEED TRANSMISSIONS;

COEFFICIENT OF FRICTIONS; FRICTION PARAMETERS; FRICTIONAL CHARACTERISTICS; NORMAL PRESSURE; OPERATING CONDITION; SLIDING DIRECTION; SLIDING SPEED; TRANSITIONAL STATE;

FRICTION;

EID: 85072460563     PISSN: 01487191     EISSN: 26883627     Source Type: Journal    
DOI: 10.4271/2002-01-0697     Document Type: Conference Paper

References (13)

1. Micklem, J. D., et al., The Magnitude of the Losses in the Steel Pushing V-Belt Continuously Variable Transmission, Proc. Instn. Mech. Engr., Part D, (1996), Vol. 210, 57-62
2. Ide, T., et al., Effect of Power Losses of Metal V-Belt CVT Components on the Fuel Economy, Proc of CVT'99, (1999), pp 93-98
3. Fujimura, O., et al., Shifting Mechanisms and Variation of Frictional Coefficients for CVT using Metal Pushing V-Belts, SAE technical paper series, No. 2000-01-0840 (2000)
4. Kanehara, S., et al., A Study on a Metal Pushing V-belt Type CVT Macroscopic Consideration for Coefficient of Friction between Belt and Pulley, Proc of JSAE CVT'96 Yokohama, No. 9636277 (1996), pp 15-22
5. Kataoka, R., et al., A Study on a Metal Pushing V-Belt type CVT-Frictional Characteristics of CVT Fluid-, Proc. JSAE spring convention, No. 132 (2001)
6. Kanehara, S., et al., Characterization of a CVT using a Metal V-belt at Transitional States, proc of CVT'99, (1999), pp 58-64
7. Kuwabara, S., et al., Power Transmitting Mechanisms of CVT Using a Metal V-Belt and Load Distribution in the Steel Ring, SAE technical paper, No. 980824 (1998)
8. Shimizu, H., et al., Development of Simulation for Analyzing the Dynamic Behavior of a Metal Pushing V-Belt for CVTs, SAE technical paper, No. 2000-01-0828, (2000)
9. Kanehara, S., et al., A Study of a Metal Pushing V-belt type CVT-part2: Compression Force between Metal Blocks and Ring Tension, SAE Trans., J. of Passengers Car, Vol. 102 (1994), pp. 1000-1009
10. Kobayashi, D., et al., A Study on the Torque Capacity of a Metal Pushing V-Belt for CVTs, SAE technical paper, No. 980822 (1998)
11. Ide, T., et al., Experimental Investigation on Shift Speed Characteristics of a Metal V-Belt CVT, JSAE, No.9636330 (1996)
12. Eguchi, M., et al., Friction Characteristic of a Paper-Based Facting Facting for a Wet Clutch, J.JAST, No. 36-7 (1991) 535-542
13. Takahashi, A., et al., Investigation of Friction Properties of Fluid for High Torque Capacity Belt CVT, Proc. JSAE Spring Convention. No. 8-99 (1999)