Continuos failure prediction model for nonlinear load paths in successive stamping and crash processes

SAE Technical Papers

Volumn , Issue , 2001, Pages

  Dell, H ^a   Gese, H ^a   Kebler, L ^b   Werner, H ^c   Hooputra, H ^c  

^a MATFEM   (Poland)

^b Thyssen Krupp Stahl AG   (Poland)

^c BMW GROUP   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

SHEET METAL; STAMPING;

CALIBRATION AND VALIDATIONS; DYNAMIC STRAIN RATE; FAILURE PREDICTION MODELS; FORMING LIMIT CURVE; LOCALIZED NECKING; MULTISTAGE EXPERIMENTS; NONLINEAR STRAIN; THEORETICAL MODELING;

STRAIN RATE;

EID: 85072449686     PISSN: 01487191     EISSN: 26883627     Source Type: Journal    
DOI: 10.4271/2001-01-1131     Document Type: Conference Paper

References (15)

1. Atkins, A.G.,: Fracture in Forming. Journal of Materials Processing Technology, 56, 1996, pp. 609-618.
2. Hosford, W.F., Duncan, J.L.,: Sheet Metal Forming: A Review. JOM, Vol. 51, 1999, pp. 39-44
3. Müschenborn, W., Sonne, H.-M.,: Einfluβ des Formänderungsweges auf die Grenzformänderungen des Feinblechs. (Influence of the strain path on the forming limits of sheet metal). Archiv Eisenhüttenwesen, 46, 1975, pp. 597-602
4. Stoughton, T.B.,: A general forming limit criterion for sheet metal forming. J. Mech. Sci., 42, 2000, pp. 1-27
5. Cao, J., Yao, H., Karafillis, A., Boyce, M.C.,: Prediction of localized thinning in sheet metal using a general anisotropic yield criterion. International Journal of Plasticity, Vol. 16, 2000, pp. 1105-1129
6. N.N.: PAM-CRASH, PAM-SAFE, Version 2000. Pam System International SA, 94588 Rungis-Cedex, France.
7. Hill, R.,: On discontinuous plastic states with special reference to localized necking in thin sheets, J. Mech. Phys. Solids, 1 (1952), pp. 19-30
8. Marciniak, Z., Kuczynski K., und, Pokora, T.,: Influence of the plastic properties of a material on the forming limit diagram for sheet metal in tension, Int. J. of Mechanical Sciences. (1973) Vol. 15, pp. 789-805
9. Cayssials, F.,: A new method for predicting FLC, IDDRG Conference, Geneva, June 17-19, 1998, pp. 443-454
10. Backhaus, G.,: Plastic deformation in form of strain trajectories of constant curvature-Theory and comparison with experimental results. Acta Mechanica. (1979) S. C. 34, pp. 193-204.
11. Dell, H. D., Eliseev, W. W.,: Materialmodell für mehrstufige Umformung mit Wärmebehandlung zwischen den Stufen. Iswestija AN SSSR. Metalli. (1991) Nr. 4. S. 171-174.
12. Nakazima, K., Kikuma, T., Hauska, K., (1972), Yamata Technical Report 264.
13. Gese, H., Dell, H.,: Macroscopic and Mesoscopic Models for Fracture in Sheet Metal forming. In: Brechet Y., (Ed.), Microstructures, Mechanical Properties and Processes. EUROMAT-Vol. 3., Wiley-VCH, 1999, pp. 160-165.
14. st Biennial Congress, Ann Arbor, Michigan, USA, June 2000, pp. 95-99.
15. Hora, P.,: Numerische Simulationsmodelle zur Voraussage des Rissversagens bei duktilen Blechwerkstoffen, Ph.D. Thesis, ETH Zurich, 1990