Transport phenomena in capillary-porous structures and heat pipes

Transport Phenomena in Capillary-Porous Structures and Heat Pipes

Volumn , Issue , 2009, Pages 1-385

  Smirnov, Henry F ^a  

^a Odessa ^*  (Ukraine)

Author keywords

[No Author keywords available]

Indexed keywords

CAPILLARITY; HEAT PIPES; HEAT TRANSFER; HYDRODYNAMICS; MASS TRANSFER; NANOTECHNOLOGY; POROSITY; THERMAL VARIABLES CONTROL; TRANSPORT PROPERTIES; VAPORIZATION;

CAPILLARY CHANNELS; EXPERIMENTAL RESEARCH; HEAT AND MASS TRANSFER; HYDRODYNAMIC PROCESS; MODERN APPLICATIONS; THERMAL CONTROL DEVICES; THERMAL CONTROL TECHNOLOGY; TRANSPORT PHENOMENA;

THERMAL ENGINEERING;

EID: 85055176541     PISSN: None     EISSN: None     Source Type: Book    
DOI: None     Document Type: Book

References (364)

1. Petukhov, B.S., Heat Transfer and Hydraulic Resistance of Laminar Liquid Flow in Tubes, Energy, Moscow, 1967, 441 pp.
2. Kalinin, E.K., Dreitzer, G.A., and Yarcho, S.A., Enhancement of Heat Transfer at Forced Convection in channels, Mechanical Engineering, Moscow, 1981.
3. Petukhov, B.S., and Roizen, L.I., Heat transfer generalized correlations for gas turbulent flow in annular cross section tubes, High-Temp. Thermophys., 2(1), 78-81, 1964.
4. Peng, X.F., and Wang, D.X., Liquid flow and heat transfer in microchannels with/without phase change, Proceedings of the Tenth International Heat Transfer Conference, Brighton, UK, Vol. 1, 159-177, 1994.
5. Wu, P.Y., and Little, W.A., Measurement of friction factor for the flow of gases in very fine channels using for microminiature Joule-Thomson refrigerators, Cryogenics, 23(5), 273-277, 1983.
6. Wu, P.Y., and Little W.A., Measurement of the heat transfer characteristics of gas flow in fine channels heat exchangers used for micro-miniature refrigerators, Cryogenics, 24(8), 415-420, 1984.
7. Tuckermann, D.B., and Pease, R.F., High performance heat sinking for VLSI, IEEE Electro. Device Lett., EDL-2(5), 126-129, 1981.
8. Tuckermann, D.B., and Pease, R.F., Optimized convective cooling using micromachined structure, Electrochem. Soc., 129(3), 98 pp., 1982.
9. Choi, S.B., Barron, R.F., and Warrigton, R.O., Fluid flow and heat transfer in micro-tubes, micromechanical sensors, actuators and systems, ASME DSC, 32, 123-134, 1991.
10. Harley, I., et al., Fluid flow in micron and submicron channels, Proc. of the IEEE, Vol. 89-THO249-3, pp. 25-28, 1989.
11. Harlow, I.N., et al., Transport processes in micron and submicron channels, Convection Heat Transfer and Transport Processes, ASME, HTD, 116, 1-5, 1994.
12. Zhang, P.I., and Xin, M.O., Liquid and convective heat transfer in microtubes, Proc. of China National Heat Transfer Conf., Beijing, 1992, pp. III89-III94.
13. Koshkin, V.K., et al., Unsteady Heat Transfer, Mechanical Engineering, Moscow, 327 pp., 1973.
14. Burundukov, A.P., Thermal and hydrodynamic non-steady processes in single-phase and two-phase media, Preprint N209, Novosibirsk, 1989.
15. Dulnev, G.N., and Yu, P., Mixtures and Composite Materials Heat Conduction, Energy, Leningrad, 1974.
16. Isatchenko, V.P., Osipova, V.A., and Sukomel, A.S., Heat Transfer Fundamentals, Energy, Moscow, 1981.
17. Cheiphez, L.I., and Naimark, A.V., Multi-Phase Processes in Porous Media, Chemistry, Moscow, 1982.
18. Luikov, A.V., Heat and Mass Transfer, Energy, Moscow, 1972.
19. Semena, M.G., Gershuni, A.N., and Zaripov, O.K., Heat Pipes with Metal-Fiber Capillary Structures, High School, Kiev, 1984.
20. Burdo, O.G., and Smirnova, Zh.B., Investigations of grooved structures thermal resistances, Eng.-Phys. J., 10(3), 535-536, 1983.
21. Burdo, O.G., and Smirnova, Zh.B., Calculations of heat pipes grooved structures thermal resistances, Radioelectron. Thermal Problems, 2, 117-118, 1982.
22. Ratiani, G.V., Mestverishvili, I.A., and Shekriladze, I.G., Thin liquid laminar films evaporation from a surface, two cases analysis, Inf. Georgian Acad. Sci., 55(3), 645-649, 1969.
23. Shekriladze, I.G., and Rusishvili, D.G., Evaporation and condensation on grooved capillary surfaces, Proceedings of the Sixth International Heat Pipe Conference, 1987, pp. 173-175.
24. Shekriladze, I.G., Evaporation and condensation on capillary surfaces, achievements and unsolved problems, Proceedings of the Tenth International Heat Pipe Conference, September 1997, pp. 1-14.
25. Shekriladze, I.G., et al., Heat Pipes of Thermal Control Systems, Energoatomizdat, Moscow, 175 pp., 1991.
26. Mistchenko, L.N., Hydrodynamic and heat transfer in low-temperature heat pipes, PhD thesis, OSAR, Odessa, 1975.
27. Aerov, M.I., and Todes, O.M., Hydrodynamic and thermal fundamentals of fluidized bed apparatuses in steady and unsteady state, Chemistry, 1968.
28. Belov, S.V., Porous Materials in Mechanical Engineering, Mechanical Engineering, Moscow, 1981.
29. Mayorov, V.A., Flow and heat transfer of single-phase cooling liquid in porous metal-ceramic media, Thermal Engineering, 1978, N1.
30. Polyaev, V.M., Mayorov, V.A., and Vasiliev, L.L., Hydrodynamic and Heat Transfer in Porous Parts of Flying Apparatus Design, Mechanical Engineering, Moscow, 1988, 168 pp.
31. Mori, Y., and Miyazaki, H., Heat transfer and mass loss characteristics of matrices for regenerative heat exchangers, Tokyo Journal, Sept., (Vol. 1), 79-87, 1967.
32. Baumann, K.H., and Blab, E., Schmidt-pathman geometrische, stromungs techisehe und termische untersuchungen an drahtggweben, Inst. Fur Kerntechnik der Technischen Untersibat, Berlin, 1966, pp. 34-72.
33. Pritula, V.V., and Zablotskaya, N.S., Experimental Investigations of Matrix Heat Exchangers Aerodynamic Characteristics, Deposit manuscript in the USSR Patent and Publishing House USSR, 1987, N3925-78.
34. Pritula, V.V., Screen metal-polymeric heat exchangers design and investigations, PhD thesis, OSAR, Odessa, 1983.
35. Kastornov, A.G., Permeable metal-fiber materials, Tech., Kiev, 1983.
36. Kovalev, S.A., and Soloviev, S.L., Evaporation and Condensation in Heat Pipes, Science, Moscow, 1989.
37. Luikov, A.V., Transition Phenomena Inside Capillary-Porous Media, Gostehizdat, Moscow, 1954.
38. Luikov, A.V., Heat and Mass Transfer in Drying Processes, Gostehizdat, Moscow, 1956.
39. Luikov, A.V., Theory of Drying, Energy, Moscow, 1968.
40. Charny, I.A., Underground Hydro-Gas Dynamic, Gostehizdat, Moscow, 1963.
41. Mayorov, V.A., Structure and hydraulic resistance of two-phase evaporative flow inside porous materials, USSR Acad. Sci. News Energy Transp., 5, 126-132, 1980.
42. Kovalev, S.A., and Ovodkov, O.A., Hydraulic resistances at liquid and gas countercurrent flow inside porous layer, HTT, 25(5), 1032-1035, 1987.
43. Kovalev, S.A., and Ovodkov, O.A., Vaporization inside porous layer mechanism investigations, Abstracts of papers of Minsk Int. Forum of HMT, Vol. 4, pp. 108-110, 1988.
44. Ovodkov, O.A., Liquid and vapor counter-current flows at bubble boiling on surfaces with porous coatings, Heat Transfer and Filtration, Dissertation thesis, Moscow Inst. of HTT of USSR Academy of Science, 1989.
45. Kovalev, S.A., Ovodkov, O.A., et al., Heat transfer at boiling on porous coatings of surfaces, Proc. of USSR Conf. of HMT, Minsk, Vol. 4(4), 10-15, 1984.
46. Smirnov, H.F., and Vinogradova, E.P., Regularities of heat transfer and thermal regimes at vaporization inside capillary-porous structures, USSR Acad. Sci. News Energy Transp., 4, 128-135, 1985.
47. Smirnov, H.F., The generalized model of boiling heat transfer, Advances in Heat Pipe Science and Techn., Proc. of 8th IHPC, Beijing, pp. 60-65, 1992.
48. Smirnov, H.F., Afanasiev, B.A., and Poniewski M., Boiling in capillary-porous structures, Proc. of Int. Conf. on Heat Transfer with Change of Phase, Part 11, Kielce, pp. 197-220, 1996.
49. Smirnov, H.F., Thermodynamic irreversibility minimization for determination of twophase structure parameters, Proc. of Int. Symp. on Physics of Heat Transfer in Boiling and Condensation, Moscow, pp. 411-417, May 1997.
50. Kovalev, S.A., and Soloviev, S.L., Heat transfer and hydrodynamics in the inverted meniscus evaporator of a heat pipe, Abstracts of 6th IHPC, France, pp. 61-67, 1987.
51. Kovalev, S.A., and Soloviev, S.L., Heat transfer in an inverted meniscus evaporator investigations, HTT, 24(1), 196-198, 1986.
52. Yatscenko, E.S., High-heat devices cooling enhancement, Dissertation thesis, Moscow Inst. of Power Eng., 1989.
53. Demidov, A.S., Sasin, V. Ya., and Yatscenko, E.S., Heat and mass transfer in heat pipes evaporation zone, Moscow, Pow. Eng. Inst. Works, 173, 44-48, 1988.
54. Styrikovich, M.A., Malyshenko, S.P., et al., Boiling on surfaces with non-heat conductive coatings peculiarities, Papers Acad. Sci. USSR, 241(2), 345-348, 1978.
55. Malyshenko, S.P., Andrianov, A.B., et al., Hysteresis and transient phenomenon by boiling on surfaces with porous coatings, Papers Acad. Sci. USSR, 256(3), 591-595, 1981.
56. Malyshenko, S.P., et al., Transient processes and boiling on surfaces with porous coatings curves peculiarities, Papers Acad. Sci. USSR, 273(4), 866 pp., 1983.
57. Styrikovich, M.A., Malyshenko, S.P., et al., Investigations of boiling processes on porous surfaces, Proc. USSR. Conf. HMT, Moscow, 4(4), 10-15, 1984.
58. Mayorov, V.A., and Vasiliev, L.L., Two-phase system of porous cooling properties, Processes of Substance and Energy Transfer at Low Temperatures in Vacuum, Minsk, 1975, pp. 55-75.
59. Mayorov, V.A., and Vasiliev, L.L., Determination of two-phase porous cooling stable system parameters, Processes of Substance and Energy Transfer at Low Temperatures in Vacuum, Minsk, 1975, pp. 76-93.
60. Vasiliev, L.L., and Mayorov, V.A., Analytical investigation of two-phase porous reversible cooling system stability, Heat Mass Transfer Probl., Minsk, 219-231, 1976.
61. Luikov, A.V., Vasiliev, L.L., and Mayorov, V.A., Theoretical analysis of two-phase cooling by evaporation inside porous structures, Int. J. HMT, 18(7/8), 863-885, 1975.
62. Mayorov, V.A., and Vasiliev, L.L., Two-phase cooling of porous heat generating element heat transfer and hydraulic resistance analytical investigation, Heat Mass Transfer Probl., Minsk, 232-258, 1976.
63. Mayorov, V.A., Heat Transfer in cooler evaporation region inside heated porous wall, USSR Acad. Sci. News, Energy Transp., 6, 141-145, 1979.
64. Mayorov, V.A., and Vasiliev, L.L., Porous wall with external heat input evaporative cooling system temperature state, Heat Transfer in Cryogenic Devices, Minsk, pp. 97-108, 1979.
65. Mayorov, V.A., and Vasiliev, L.L., Temperature state of porous heat exchanger with account for heat carrier thermal conductivity, Heat Transfer in Cryogenic Devices, Minsk, pp. 108-119, 1979.
66. Mayorov, V.A., Vasiliev, L.L., and Polyaev, V.M., Evaporation inside porous materials flow structure, heat transfer and hydraulic resistance, Proc. USSR Conf. of HMT, Minsk, 4(4), 9-13, 1984.
67. Nakoryakov, V.E., and Petrick, P.T., Heat exchange during film boiling and condensation in a granular lager, Two-Phase Flow Modeling and Experimentation, Proc. of the First Intern. Symp. on Two-Phase Modeling and Experimentation, Rome, pp. 253-260, 1995.
68. Nakoryakov, V.E., Petrick, P.T., et al., Film boiling in granular bed, Russ. J. Eng. Thermophys., 2(4), 200-310, 1992.
69. Bau, H.H., and Torrance, K.E., Boiling in low-permeability porous materials, Int. J. Heat Mass Transfer, 25(1), 45-55, 1982.
70. Bau, H.H., and Torrance, K.E., Thermal convection and boiling in a porous media, Lett. Heat Mass Transfer, 9, 431-441, 1982.
71. Smirnov, H.F., Boiling on surfaces covered by capillary-porous structures, heat transfer approximated theory, Thermal Eng., 9, 40-43, 1977.
72. Khvostov, V.I., and Marinichenko, S.I., Stability of evaporation from porous structure at liquid transport by capillary forces, EPJ, 10(2), 135-139, 1979.
73. Ogniewez, Y., and Tien, C.L., Analysis of heat pipe phenomenon in porous media, AIAA Paper, 1-6, 79-109, 1979.
74. Wang, C.Y., and Groll, M., Dry-out heat fluxes in composite porous layers heated from below, Advances in Heat Pipe Science and Technology, Proc. of 8th IHPC, 1992, Beijing, pp. 65-68.
75. Afanasiev, B.A., and Smirnov, H.F., Experimental investigations of heat transfer and critical heat fluxes at boiling in capillary-porous structures, Thermal Eng., 5, 65-67, 1979.
76. Afanasiev, B.A., Zrodnikov, V.V., Koba, A.L., et al., Boiling in capillaries, slits and capillary-porous structures heat transfer, Heat Transfer and Hydrodynamics at Boiling and Condensation, Collected works, pp. 75-82, Nov. 1979.
77. Smirnov, H.F., Koba, A.L., Afanasiev, B.A., and Zrodnikov, V.V., Boiling in capillaries, slits and other tighten conditions heat transfer, Heat and Mass Transfer-V, Sci. Technol., Minsk, 3, 1, 193-197, 1976.
78. Smirnov, H.F., and Afanasiev, B.A., Experimental investigations of boiling inside screen structures of heat pipes, RETP, 2, 22-27, 1979.
79. Afanasiev, B.A., Vaporization inside screen capillary-porous structures investigations (heat transfer, critical heat fluxes, mechanism), Dissertation thesis, Odessa, 1981.
80. Moss, A.R., and Kelly, I.A., Neutron radiographic study of limiting planar heat pipe performance, Int. J. Heat Mass Transfer, 14, 491-502, 1980.
81. Vershinin, S.V., Fershtater, Yu.G., and Maidanik, Yu.F., Contact thermal resistance influence on evaporation from small-porosity capillary structures heat transfer, HTT 30(4), 811-817, 1992.
82. Borodkin, A.A., Liquid evaporation from capillary open surface grooved channels heat transfer intensity calculation method working out for HP structures optimization, Dissertation thesis, Moscow Inst. of Power Eng., 1988.
83. Borodkin, A.A., and Sasin, V. Ya., Liquid evaporation from capillary open surface grooved channels heat transfer intensity, Moscow Power University Scientific Works, Industrial Energy Application, Moscow, Vol. 28, 94-100, 1984.
84. Gorbis, Z.R., Smirnov, H.F., and Savchenkov, G.A., Liquid boiling in granular bed heat transfer investigations, (EPJ), 26(3), 544-545, 1974.
85. Gorbis, Z.R., and Berman, M.I., Experimental investigations of boiling heat transfer in thermal fluidization particles layer conditions, (EPJ), 27(4), 389-396, 1974.
86. Berman, M.I., and Gorbis, Z.R., Distillate water boiling in dispersed granular bed heat transfer, Thermal Eng., 11, 86-88, 1973.
87. Gorbis, Z.R., and Berman, M.I., Liquid boiling inside dispersed particles layer heat transfer, HMT-V, Sci. Technol., Minsk, 3, 1, 56-60, 1976.
88. Mankovsky, O.N, Fridgant, L.G., et al., Boiling on submerged with porous coatings surfaces mechanism discussion, (EPJ), 30(2), 310-316, 1976.
89. Fridgant, L.G., Boiling heat transfer enhancement with porous coating help in heat exchangers of low-temperature gas separation apparatuses, Dissertation thesis, 1985.
90. Chernobulsky, I.I., and Tananyako, Yu.M., Liquid boiling in annular slit heat transfer, J. Tech. Phys., 26(10), 2316-2322, 1956.
91. Ishibashi, T., and Nishikawa, H., Saturated boiling heat transfer in narrow spaces, J. Heat Mass Transfer, 12(8), 863-893, 1969.
92. Azarskov, V.M., Refrigerants boiling in slit channels of plate evaporators experimental investigations, Dissertation thesis, Leningrad Food Tech. Refrig. Inst. Publ., 1973.
93. Gogolin, A.A., Danilova, G.N., Azarskov, V.M., and Mednikova, N.M., Heat transfer enhancement in refrigeration machines evaporators, Food Ind., 287 pp., 1982.
94. Malyugin, G.I., Ice generator and sublimator internal heat transfer investigation and enhancement, Dissertation thesis, Leningrad Food Tech. and Refrig. Inst. Publ., 1976.
95. Zemskov, B.B., Refrigerants boiling in vertical complex form channels heat transfer and hydrodynamic investigations, Dissertation thesis, Leningrad Food Techn and Refrig. Inst. Publ., 1978.
96. Grigoriev, V.A., Krokhin, Yu.I., and Kulikov, A.S., Vertical slit channels boiling heat transfer, Moscow, Power University Works, Industrial Energy Application, Vol. 141, 58-68, 1972.
97. Grigoriev, V.A., and Krokhin, Yu.I., Real phase velocity and vapor quality by boiling in slit channels, HTT, 2(1), 145-148, 1972.
98. Antipov, V.I., Grigoriev, V.A., and Illarionov, A.G., Liquid nitrogen boiling in small diameter tubes (capillaries) experimental investigations, Moscow, Final papers, pp. 146-151, 1968-1969.
99. Labuntsov, D.A., et al., Boiling inside small diameter tubes heat transfer coefficients experimental investigations, HEIN, Energy and Transport Mechanical Engineering, N5, 1971.
100. Labuntsov, D.A., et al., Boiling inside small diameter tubes heat transfer coefficients experimental and analytical investigations, HEIN, ETME, 7, 68-73, 102-105, 1970.
101. Leontiev, A.I., et al., One vaporization center in slit channel heat transfer experimental investigation, Moscow High Tech. School Work, 195, 34-41, 1975.
102. Leontiev, A.I., et al., Ethanol water solution boiling in slit channel heat transfer experimental investigation, HEIN, ETME, 3, 85-87, 1977.
103. Leontiev, A.I., et al., Microfilm by liquid boiling in weak gravity condition role, nonlinear wave, Proc. in Two-Phase Media, pp. 266-275, Nov. 1977.
104. Leontiev, A.I., Mironov, B.M., and Korneev, S.D., Ethanol water solution boiling in slit plate-parallel channel heat transfer characteristics investigations, Heat Transfer Problems (Moscow Wood Tech. Ins. W.), 101, 98-108, 1977.
105. Koba, A.L., and Smirnov, H.F., Boiling in submerged into liquid pool horizontal slit heat transfer and critical heat fluxes, EPJ, 27(4), 738-739, 1974.
106. Koba, A.L., and Smirnov, H.F., Boiling in submerged into liquid pool inverted plate heat transfer and critical heat fluxes, RETP, 2, 70-74, 1974.
107. Koba, A.L., and Smirnov, H.F., Boiling in submerged into liquid pool horizontal plate slit heat trans., and critical heat flux, RETP, 3, 126-134, 1977.
108. Koba, A.L., Afanasiev, B.A., et al., Heat transfer investigations at boiling on horizontal plate slit, Works of En. Inst. Krig. Dep. in All-Un. In. P., N1029-78 DSP, 1978.
109. Koba, A.L., Boiling on horizontal plate channels submerged into liquid pool (heat transfer, mechanism, internal characteristics, heat transfer crisis), Dissertation thesis, Odessa., Acad. of Refrigeration, 1979.
110. Klimov, S.M., Bologa, M.K., and Smirnov, H.F., Boiling in pool horizontal plate slit heat transfer under electric field action investigations, ETM, 5, 48-52, 1978.
111. Klimov, S.M., Bologa, M.K., and Smirnov, H.F., Electric field action influence on boiling in pool narrow horizontal plate slits heat transfer and critical heat fluxes, Electron. Treatment Mater., 5, 45-49, 1979.
112. Klimov, S.M., Bologa, M.K., and Smirnov, H.F., Mechanism, internal characteristics of boiling in pool horizontal plate slit heat transfer under electric field action investigations, Electron. Treatment Mater., 5, 46-50, 1980.
113. Klimov, S.M., Bologa, M.K., and Smirnov, H.F., Mechanism of formation and pressing of dry spots by boiling in liquid pool submerged slit under electric field action, Electron. Treatment Mater., 5, 56-62, 1980.
114. Mironov, B.M., Lobanova, L.S., and Shadrin A., Liquid boiling in vertical plate par. slit chan local heat transfer crisis, HEIN, Energy, 7, 85-88, 1978.
115. Klimov, S.M., Bologa, M.K., and Smirnov, H.F., Boiling in pool horizontal plate slit heat transfer under electric field action, Heat Transfer, Minsk, 4(part 1), 22-27, 1980.
116. Klimov, S.M., Boiling in pool horizontal plate slit heat transfer under electric field action, Dissertation thesis, Odessa, Acad. of Refrigeration, 1982.
117. Danilova, G.N., and Dyundin, V.A., Refrigerants R-12 and R-22 boiling on finned tubes bundle heat transfer, Refrigeration, 7, 40-42, 1971.
118. Dyundin, V.A., Refrigerants boiling on finned surfaces heat transfer, Dissertation thesis, 1971.
119. Tiktin, S.A., Vapotron Technology, Technika, Kiev, 151 pp., 1971.
120. Kovalev, S.A., Traditional and dissociating liquids pool boiling on isothermal and non-isothermal (finned) surfaces heat transfer and stability mechanism investigations, Dissertation thesis, Moscow, 1977.
121. Petukhov, B.S., Kovalev, S.A., and Geshele, V.D., Boiling on finned surface, Heat Transfer and Hydrodynamics, Science, Moscow, pp. 5-14, 1977.
122. Petukhov, B.S., and Geshele, V.D., Liquid boiling in slit experimental methods and results, HTT, 13(1), 321-329, 1975.
123. Bezrodny, M.K., Butuzov, A.I., and Sosnovsky, V.I., Value of gap in finned spaces of finned tube influence on liquid pool boiling heat transfer, RETP, 2, 19-28, 1975.
124. Bezrodny, M.K., Sosnovsky, V.I., and Alekseenko, D.V., Refrigerant R-11 pool boiling in slit channels heat transfer and critical heat fluxes experimental investigations, Thermal Processes in Electronic High-Wave Devices, Ser. HWD. Electronics, Vol. 3(43), 1975.
125. Sosnovsky, V.I., Boiling in slit channels and on finned surfaces refrigerants heat transfer and critical heat fluxes experimental investigations, Dissertation thesis, Kiev National Polytechnic University, 1977.
126. Yagov, V.V., Liquid pool boiling in low pressures field investigations, Dissertation thesis, Moscow Inst. of Power Eng., 1971.
127. Belsky, V.K., Refrigerant R-12 boiling on tubes bundle and on single wrapped tubes heat transfer investigations, Refrigeration, 2, 41-44, 1970.
128. Kupriyanova, A.V., Ammonia boiling on tubes heat transfer investigation, Dissertation thesis, Leningrad, 1970.
129. Vishnev, I.P., et al., Helium bubbles boiling thermal parameters, Heat Mass Transfer, Inst. of HMT of Acad. Sci. BSSR, 2(part 1), 263-270, 1972.
130. Vishnev, I.P., et al., Helium-1 bubble pool boiling in vertical channels pressure influence, Acad. of Sci. of USSR, 206(5), 1090-1092, 1970.
131. Grigoriev, V.A., Pavlov, and Ametistov, E.D., Cryogenic Liquids Pool Boiling, Energy, Moscow, 288 pp., 1983
132. Gorokhov, V.V., Helium boil. by natural circulation in heat exchangers investigation, Dissertation thesis, Moscow Inst. of Chem. Eng., 1975.
133. Petukhov, B.S., Zukov, V.M., and Shildkret, V.M., Helium in small diameter channels boiling heat transfer investigation, Cryo-Electro-Technology and Energy, Part III, Kiev, pp. 104-109, 1977.
134. Shildkret, V.M., Helium two-phase flow in channels heat transfer and hydraulic resistance, Dissertation thesis, Moscow, 1981.
135. Kutateladze, S.S., and Nakoryakov, V.E., Heat and Mass Transfer and Waves in Gas-Liquid Systems, Science, Novosibirsk, 1984, 300 pp.
136. Kutepov, A.L., Sterman, L.S., and Styushin, N.G., Hydrodynamic and Heat Transfer by Vaporization, Moscow High School, 484 pp., 1983.
137. Lippert, L., and Pitts, A., Heat Transfer Problems, Atomizdat, Moscow, pp. 142-198, 1967.
138. Smirnov, H.F., Initial micro-layer under bubble by boiling thickness elementary calculation method, EPJ, 28(3), 503-508, 1975.
139. Kozhelupenko, Yu.D., Smirnov, H.F., and Koba, A.L., Subcooled liquid boiling heat transfer crisis in narrow annular channels by small liquid velocities, Abstracts of paper. Boiling and Condensation Processes Thermo-Physics and Hydrodynamics, Riga, Vol. 1, pp. 154-155, 1982.
140. Kozhelupenko, Yu.D., Water and water solution boiling in capillary and annular channels heat transfer and critical heat fluxes by cooling systems of radio-electronic equipment (REE) working conditions, Dissertation thesis, Odessa, 1984.
141. Baranenko, V.I., and Chichkan, L.A., Liquid microfilm thickness measurement method and some results by boiling inside slit channel, Boiling and Condensation, Riga, Vol. 2, pp. 3-12, 1978.
142. Chichkan, L.A., Liquid boiling heat transfer local characteristics and mechanism investigation on laser diffraction interferometer application base, Dissertation thesis, Kiev National Polytechnic University, 1982.
143. Kutateladze, S.S., Heat Transfer and Hydraulic Resistance, Reference Manual, Energoatomizdat, Moscow, 366 pp., 1990.
144. Diev, M.D., A study of vapor bubble departure during boiling in narrow slit channel, the physics of heat transfer in boiling and condensation, Proc. of Int. Symp., May 21-24, pp. 345-350, 1997.
145. Labuntsov, D.A., Developed bubble boiling heat transfer approximated theory, USSR Acad. Sci. News Energy Transp., 1, 58-71, 1963.
146. Ferell, I.K., Alexander, E.G., and Piver, W.T., Vaporization heat transfer in heat pipe wick materials, AIAA Paper, 256, 1-12, 1972.
147. Davis, W.R., and Ferell, I.K., Evaporative heat transfer of liquid potassium in porous media, Heat Transfer Ther. Contr. Appl., 39, 198-199, 1975.
148. Ferell, I.K., and Alexander, E.G., Vaporization heat transfer in capillary wick structures, Chem. Eng. Symp. Ser., 66, DD2, 1970.
149. Ferell, I.K., and Johnson, D.E. The mechanism of heat transfer in the evaporative zone of a heat pipe, ASME Heat 70-HT/sptn, June 1971.
150. Abhat, A., and Seban, R.A., Water, acetone and ethanol boiling and evaporation in heat pipe wicks, Heat Transfer, 3, 74-83, 1988.
151. Seban, R.A., and Abhat, A., Steady and maximum evaporative from screen wicks, Paper ASME, WA/HT-12, 1971.
152. Corman, I.C., and Walmet, W.L., Vaporization from capillary wick structures, Paper ASME NHT-35, 1-8, 1971.
153. Marto, P.I., Mosteller, W.L., Effect of nucleate boiling on the operation of lowtemperature heat pipes, ASME Paper, No-69-HT-24, pp. 1-8, 1969.
154. Sasin, V.Ya., Fedorov, V.N., and Sorokin, A.Ya., Heat pipe with low-boiled heat carrier experimental investigation, Moscow, Pow. Eng. Inst. Wor. Coll. Connected with Sci.-Techn. Conf., pp. 79-F84, 1969.
155. Voronin, V.G., Revyakin, A.V., Sasin, V.Ya., and Tarasov, V.S., Low-temperature heat pipes for flying apparatuses, Mech. Engin., Moscow, 200 pp., 1976.
156. Asakyavichus, I.P., Zhukauskasm A.A., et al., Heat pipes working by moderate temperatures heat transfer mechanism, Lithonia SSR Works, Ser. B, 5(102), 81-88, 1977.
157. Asakyavichus, I.P., Zhukauskas, A.A., et al., Refrigerant-113, ethanol and water boiling in screen wicks heat transfer, Lithonia SSR Works, Ser. B., 1(104), 87-93, 1978.
158. Asakyavichus, I.P., and Eva, V.K., Heat transfer inside low-temperatures heat pipes problems, Heat Transfer, Soviet investigations, pp. 458-461, 1978.
159. Antonenko, V.A., Boiling and Evaporation in thin liquid films heat transfer investigations, Dissertation thesis, Kiev Ins. Tech. Therm., 1978.
160. Tolubinsky, V.I., Antonenko, V.A., and Ostrovsky, Yu. N., Evaporative zone of heat pipe vaporization heat transfer regularities and mechanism, USSR Acad. Sci. News Energy Transp., 1, 141-148, 1979.
161. Tolubinsky, V.I., et al., Liquid evaporation in capillary wicks of low-temperature heat pipes limiting heat fluxes, HTT, 18(12), 367-373, 1980.
162. Tolubinsky, V.I., et al., Drop carry over phenomenon in liquid evaporative from capillary structures, Lett. Heat Mass Transfer, 5(6), 339-347, 1978.
163. Tolubinsky, V.I., et al., Vaporization regimes inside low-temperature heat pipes wicks, Proc. of USSR Conf. of HMT, Minsk, 6(1), 26-31, 1984.
164. Kudritsky, G.R., Evaporation on small sizes surfaces, coated capillary-porous structures (by heated surface local heat source using), heat transfer enhancement, Dissertation thesis, Kiev Institute of Technical Thermophysics, Kiev, 1985.
165. Tolubinsky, V.I., et al., Boiling on surfaces, covered by thin screen wick, heat transfer, Ind. Appl. Thermal Eng., 11(4), 3-7, 1989.
166. Kudritsky, G.R., Ostrovsky, Yu N., and Antonenko, V.A., Vaporization mechanism inside screen wicks of low-temperature heat pipes investigation, Ind. Appl. Thermal Eng., 12(4), 61-65, 1990.
167. Antonenko, V.A., and Kudritsky, G.R., Vaporization process inside heat pipes wick mechanism investigation results, EPJ, 90(1), 12-19, 1991.
168. Kudritsky, G.R., and Kolomiez, E.A., Surface geometry parameters influence on heat transfer and initial boil, Moment, IATE, 16(1), 18-21, 1994.
169. Kudritsky, G.R., Boiling in defined geometry characteristics of heating surface conditions influence on heat transfer, Dissertation thesis, Kiev Institute of Technical Thermophysics, Kiev, 1995.
170. Smirnov, H.F., Afanasiev, B.A., et al., Heat transfer and limiting heat fluxes at vaporization in construction capillary-porous structures of heat pipes, Prepr. Proceeding of 7th IHPC, Minsk, USSR, paper A-16, 1990.
171. Semena, M.G., et al., Transient from evaporation up to boiling regimes in low-temperature heat pipes with fiber-metal wicks, Heat and Mass Transfer-7, Minsk, 6, 117-123, 1980.
172. Hasegawa, S., Echigo, R., and Ikie S., Boiling characteristics and burnout phenomena on heating surface covered with woven screens, J. Nucl. Sci. Technol., 12(11), 722-724, 1975.
173. Semena, M.G., Zaripov, O.K., and Gershuni, A.N., Heat Transfer in heat pipes heating zone with metal-fiber capillary structures, HTT, 24(2), 67-73, 1982.
174. Ornatsky, A.P., Semena, M.G., and Timofeev, V.I., Maximum heat fluxes by boiling on plane metal-fiber wicks in conditions, typical for heat pipes investigation, EPJ, 35(1), 212-219, 1978.
175. Shapoval, A.A., Zaripov, O.K., and Semena, M.G., Water boiling on surfaces with metalfiber porous coatings heat transfer intensity investigation, Thermal Eng., 12, 63-65, 1983.
176. Shapoval, A.A., Water and acetone boiling on surfaces, covered metal-fiber capillaryporous coatings, Dissertation thesis, Kiev Nat. Polyt. Univ., 1978.
177. Semena, M.G., et al., Water boiling on porous surfaces heat transfer intensity pressure influence peculiarity, EPJ, 62(1), 779-782, 1992.
178. Semena, M.G., et al., Water boiling on porous surfaces heat transfer intensity pressure influence investigation, Proc. Int. For. Minsk., Heat and Mass Transfer, Vol. 4, Part 1, pp. 59-62, 1992.
179. Fridrikhson, Yu.V., Kravetz, V.Yu., and Semena, M.G., Vaporization acting centers density calculation by liquid boiling on metal-fiber capillary-porous structures, EPJ, 66(5), 600-605, 1994.
180. Fridrikhson, Yu.V., Liquid pool boiling on metal-fiber coating heat transfer, Dissertation thesis, Kiev Nat. Polyt. Univ., 1995.
181. Labuntsov, D.A., Bubble boiling heat transfer problems, Thermal Eng., 9, 14-19, 1972.
182. Maidanik, Yu.F., Working out and investigation of low-temperature heat pipes, which can be working by different positions in gravity field, Dissertation thesis, Sverdlovsk Polyt. Univ., 1977.
183. Dolgirev, Yu. E., Heat pipes, working by different position in volumetric forces field, investigation, calculation and optimization, Dissertation thesis, Sverdlovsk Polyt. Univ., 1977.
184. Maidanik, Yu.F., Fershtater, Yu.G., and Pastukhov, V.G., Loop heat pipes: working out; investigations; engineering calculations elements, Acad. Sci. USSR Sci. Pap., Ural Part. Sverdlovsk, 1989.
185. Kiseev, V.M., et al., Plane heat pipe with separate vapor and liquid channels evaporation zone optimization, Sverdlovsk, N4162-84DEP, 1984.
186. Kiseev, V.M., et al., Antigravity heat pipe with flat evaporator wick closing wall thickness optimization, Sverdlovsk, N4160-84DEP, 1984.
187. Maidanik, Yu.F., Loop heat pipes and two-phase loops with capillary pumping, Dissertation thesis, Moscow Inst. of Power Eng., 1993.
188. Dyundin, V.A., and Borishanskaya, A.V., Liquid boiling heat transfer surface conditions influence on, HMT M., 2, 177-179, 1972.
189. Danilova, G.N., Guigo, E.I., et al., Low-temperature liquids boiling at low heat fluxes heat transfer enhancement, Proc. of Int. For in Minsk, HMT HMT-5 M., 3(Part 1), 22-31, 1976.
190. Dyundin, V.A., Danilova, G.N., and Borishanskaya, A.V., Refrigerants boiling on surfaces with coated coverings, Boiling and Condensation, Riga, Vol. 2, pp. 7-19, 1977.
191. Dyundin, V.A., et al., Refrigerants boiling on tubes surfaces with metallic coverings experimental investigations, Refrigeration and Cryogenic Technology, pp. 121-127, 1975.
192. Bukin, V.G., Danilova, G.N., and Dyundin, V.A., Refrigerants moving film washing horizontal tubes bundle coated porous covering by boiling heat transfer, Heat Mass Transfer-5, 4(part 1), 16-21, 1980.
193. Poznyak, V.E., Orlov, V.K., and Saviliev, V.N., Coating porous covering on boiling surface of condenser-evaporator heat transfer enhancement, Chem. Oil Mech. Eng., 3, 43-47, 1980.
194. Orlov, V.K., and Saveliev, V.N., Cryogenic liquids boiling by lower atmospheric pressure heat transfer enhancement, Thermal Eng., 4, 62-64, 1980.
195. Orlov, V.K., et al., Cryogenic liquids boiling heat transfer enhancement, Heat Transfer and Hydrodynamic by Boiling and Condensation, 21th Sibirsk Thermophysical Seminar Proc., October, pp. 83-89, 1978.
196. Royezin, L.I., et al., Nitrogen and refrigerant-113 boiling on metal porous coatings heat transfer, HTT, 20(2), 304-310, 1982.
197. Tunik, A.T., Bolshakov, A.A., and Techwer, Ya. Ch., Liquid dielectric boiling on porous coated surfaces heat transfer intensity influence on, High School News, Acad. Sci. USSR Ser. Phys. Math., 27(3), 364-369, 1978.
198. Ito, T., Fudzita, K., and Nisikawa, K., Surfaces with high boiling heat transfer coefficient, Sci. Mech., 31(1), 1979.
199. Sirotin, A.G., Dvoiris, A.D., et al., Refrigeration machines efficiency increasing for account of application of tubes with porous coatings in heat exchangers-evaporators, Gas Ind., 12, 28-32, 1976.
200. Dvoiris, A.D., Sirotin, A.G., and Sakharova, G.P., Natural gas liquefaction processes enhancement, USSR Acad. Sci. News Eng. Transp., 4, 145-151, 1980.
201. Sirotin, A.G., Liquefied hydrocarbon gas boiling on porous surfaces heat transfer, New equipment and technology of preparation and treatment gas and condensate, 1, 104-116, 1982.
202. Nakayama, W., Daykoku, T., Kuwahara, H., and Nakajima, T., Boiling on porous surface heat transfer enhancement dynamic model. Part 1, Experimental Investigation; Part 2. Analytical Model, ASME Works, 102(3), 62-69, 69-74, 1980.
203. Bergles, A., Pool boiling on metal porous coatings heat transfer characteristics, ASME Works, 104(2), 56-64, 1982.
204. Nakayama, W., Daikoku, T. and T. Nakajima, Pores parameters and system pressure influence on boiling heat transfer in saturation regime, ASME Works, 104(2), 65-72, 1982.
205. Martin, P.J. and Lepert, V. Dielectric liquids pool boiling on structural surface heat transfer, ASME Works, 104(2), 72-80, 1982.
206. Styrikovich, M.A., et al., Mass Transfer by boiling in capillary-porous structures investigations modern state. Review, HTT, 18, 625-633, 1980.
207. Picone, L.F., Whyte, D.D., and Taylor, G.R., Radiotracer studies of hideout at high temperature and pressure, Wes. Elect. Corp. Atom. Pow. Div, WCAP-3731, June 1963.
208. Polonsky, V.S., et al., Boiling in capillary-porous structures accompanied by concentration model, Paper Acad. Sci. USSR, 241(3), 579-583, 1978.
209. Styrikovich, M.A., et al., Iron oxides deposits influence on mass transfer intensity in vapor generating channels, Moscow Pow. Eng. Inst. Wor. Coll., 128, 54-62, 1972.
210. Styrikovich, M.A., et al., Mass transfer intensity in vapor generating channels experimental investigations, HTT, 15(2), 225-233, 1977.
211. Styrikovich, M.A., et al., Mass Transfer conditions in vapor generating channels experimental investigations with heat-generating in cosine law, HTT, 16(3), 325-333, 1978.
212. Dvoryaninov A.V., et al., Corrugated screen wick heat pipe characteristics experimental investigation, EPJ, 37(1), 13-19, 1979.
213. Aptekar, B.F., and Baum, Ya.M., Heat carrier mass inside low-temperature heat pipes with corrugated screen wicks influence on limiting heat fluxes, HTT, 20(1), 150-154, 1982.
214. Zigalov, V.G., et al., Heat pipes with corrugated capillary structures experimental investigation, RETP, 3, 117-118, 1983.
215. Afanasiev, B.A., et al., Condensation and evaporation inside heat pipes with corrugated wicks, 7th All-Union HMT Conf., Minsk, 1, Part 2, 8-14, 1984.
216. Silinsky, A.L., Heat pipes with corrugated wicks produced from smooth metal foil for power transistors cooling, Dissertation thesis, L. In. of Fd. Tech, 1986.
217. Afanasiev, B.A., Vinogradova, E.P., and Smirnov, H.F., Heat pipes with corrugated wicks produced from smooth metal foil heat transfer and it maximum thermal power, EPJ, 50(1), 58-65, 1986.
218. Vinogradova, E.P., Heat Transfer and maximum heat fluxes of heat pipes with corrugated capillary structures, Dissertation thesis, Odes, Acad. of Refrigeration, 1988.
219. Styrikovich, M.A., Leontiev, A.I., Polonsky, V.S., et al., Mass transfer intensity in vapor generating channels experimental investigations, Int. Sem. Mom. Heat and Mass Transfer in Two-Phase Energy and Chemical Systems, Dubrovnic, Jugoslavia, September, pp. 4-9, 1978.
220. Cohen P., Concentration by solution boiling theoretical model, Am. Inst. Chem. Eng. Symp., 138, 70-71, 1974.
221. Malyshenko, S.P., and Andrianov, A.B., Initial boiling on surfaces with porous coatings curve part and boil hysteresis, HTT, 25(3), 563-572, 1987.
222. Andrianov, A.B., and Malyshenko, S.P., Porous coatings influence on boiling heat transfer intensity, USSR Acad. Sci. News Energy Transp., 1, 139-149, 1989.
223. Malyshenko, S.P., and Andrianov, A.B., Irreversible phase transients by boiling on surfaces with porous coatings, Preprint of Inst. High Temp. of Acad. of Sci. of USSR, N1-293, 1990.
224. Andrianov, A.B., et al., Composite super-conductivity materials cryostat stabilization improvement with porous coating help, Preprint of Inst. High Temp. of Acad. of Sci. of USSR, N4-227, 1987.
225. Techwer, Ya.Ch., Syi, Ch.N., and Temkina, V.S., Liquid boil on porous surface and heat transfer hysteresis, Preprint of Ac. of Est. SSR. Tallin, 1989.
226. Malyshenko, S.P., Percolation transition at boiling on porous coated surfaces, Physics of Heat Transfer in Boiling and Condensation, Proceedings of Int. Symp., Moscow, pp. 319-333, 1997.
227. Zuev, A.v., and Malyshenko, S.P., Dry-out phenomena at two-phase in tubes with porous coating, 10th Int. Heat Trans. Conf., Brighton, UK, Vol. 6, pp. 147-150, 1994.
228. Kovalev, S.A., and Soloviev, S.L., Heat Transfer in an inverted meniscus evaporator investigations, HTT, 24(1), 196-198, 1986.
229. Poniewski, M.E., Afanasiev, B.A., and Wojcik, T.M., Hysteresis of boiling heat transfer on porous covering, Proceedings of the 30th National Heat Transfer Conf., Poland, Vol. 7, pp. 197-220, 1996.
230. Styrikovich, M.A., Leontiev, A.I., and Malyshenko, S.P., Non-volatile impurities transfer mechanism by boiling on surfaces covered by porous structures, HTT, 14(1), 998-1006, 1976.
231. Makbeth, R.V., Boiling on surface overlaid with a porous deposit, heat transfer rates obtainable by capillary actions. AEEW-R-711, Winfrith, 1971.
232. Pichlak, U.L., and Techwer, Ya.Ch., Porous coating influence on boiling heat transfer, USSR Acad. Sci. News Energy Transp., 3, 13-17, 1983.
233. Techwer, Ya.Ch., and Tunik, A.G., Boiling on porous coating surface, USSR Acad. Sci. News, Ser. Phys. Math., 28(1), 68-27, 1979.
234. Krokhin, Yu.I., and Kulikov, A.S., Vaporization process in capillary-porous structures approximated hydrodynamic theory, HTT, 21(5), 952-958, 1983.
235. Kulikov, A.S., Liquid flow inside pores and limiting heat fluxes definition by vaporization on porous coated surfaces problem solution, Dissertation thesis, Moscow Inst. of Power Eng., 1984.
236. Borishanskaya, A.V., Gotovsky, M.A., and Dyundin, V.A., Boiling on surfaces with capillary-porous coverings heat transfer calculation, Boiling and Condensation, Riga, Vol. 2, pp. 29-36, 1978.
237. Aleshin, A.N., et al., Vaporization on porous coated surfaces heat transfer investigation, HTT, 18(2), 1098-1101, 1980.
238. Soloviev, S.L., and Kovalev, S.A., Liquid evaporation from capillary-porous body heat transfer, 7th All-Union HMT Conf., Minsk, Vol. 6, pp. 22-25, 1984.
239. Kovalev, S.A., and Soloviev, S.L., Liquid evaporation and boiling on porous coated surfaces heat transfer, Problems papers of 7th All-Union HMT Conf., Minsk, pp. 3-12, 1985.
240. Kovalev, S.A., and Soloviev, S.L., Liquid boiling on porous coated surfaces models, Problems papers, Heat Mass Transfer-8 Int. For. Minsk, pp. 3-18, 1988.
241. Webb, R.L., Principles of Enhanced Heat Transfer, Wiley-Interscience, New York, 1994.
242. Webb, R.L., Advances in Modeling Enhanced Heat Transfer Surface, Proc. of the 10th Int. Heat Trans. Conf., Brighton, UK, Vol. 4, pp. 445-449, 1994.
243. Rosenfeld, I.H., Nucleate Boiling Heat Transfer in porous wick structures, ASME, Heat Transfer Equipments Fund. Book, NH00500, 108, 47-55, 1989.
244. Nishikava, K., Ito, T., and Tamaka K., Enhanced heat transfer by nucleate boiling on sintered metal layer, Heat Transfer Jpn. Res., 8, 65-81, 1979.
245. O’Neil, P.S., Gottzman, G.F., and Turbot, T.W., Novel heat exchanger increases cascade cycle efficiency for national gas liquefaction, in Advances in Cryogenic Engineering, K.D. Fimmounhaus, ed., Plenum, NY, pp. 402-437, 1972.
246. Webb, R.L., Nucleate boiling on porous coated surface, Heat Transfer Eng., 3(304), 71-82, 1983.
247. Rosenfeld, I.H., Modeling of heat transfer into a heat pipe for a localized heat input zone, AICHE Symp. Ser. Heat Transfer, Pittsburgh, 83, 71-76, 1987.
248. Shaubakh, R.M., Dussinger, P.M, and Bogart, J.E., Boiling in heat pipe evaporator wick structures, 7th IHPC Proceedings, Minsk, pp. 1-15, 1990.
249. Singh, B.S., and Shaubakh, R.M., Boiling and two-phase flow in the capillary porous structure of a eat pipe, ASME Fed., 60/91, 1988.
250. Gorbis, Z.R., Berman, M.I., and Beliy, L.M., Invention Certificate N449227 of USSR Heat Transfer Enhancement Method, Bulletin of Inv., N41, 1974.
251. Chulkin, O.A., Hydrodynamic heat transfer deposit prevention in evaporator with solid particles fluidized bed, Dissertation thesis, 1984.
252. Berman, M.I., Boiling process on heating surfaces submerged into solid particles dispersed layer investigation, Dissertation thesis, Odessa Academy of Refrigration, 1984.
253. Berman, M.I., Gorbis, Z.R., and Alexandrov, V.I., Boiling on horizontal tubes bundle heat transfer in developed fluidization conditions, EPJ, 36, 337-343, 1979.
254. Berman, M.I., and Gorbis, Z.R., Process analysis and boiling on heating surface, submerged into solid particles dispersed layer, heat transfer experimental data generalization, EPJ, 38, 5-15, 1980.
255. Berman, M.I., and Chulkin, O.A., Boiling into fluidized particles bed deposits prevention process experimental investigation and model working out, Minsk, N3140-83DEP, 1983.
256. Berman, M.I., and Chulkin, O.A., Boiling on horizontal tubes bundle in developed fluidized particles bed conditions heat transfer and hydrodynamic, EPJ, 43, 718-727, 1982.
257. Smirnov, H.F., Liquid pool boiling in dispersed material submerged bed heat transfer, EPJ, 34, 792-798, 1978.
258. Tuchnin, A.M., Vasanova, L.K., and Siromyatnikov, N.I., Sub-cooled boiling in liquid fluidized particles bed by cylinder cross flow heat transfer, EPJ, 36, 389-394, 1979.
259. Tuchnin, A.M., Heat transfer in liquid fluidized bed by high heat fluxes investigation, Dissertation thesis, Sverdlovsk Polyt. Univ., 1980.
260. Baranenko, V.I., Asmolov, V.G., and Kirov, V.S., Thermodynamic and Heat Transfer in Nuclear Power Systems with Gas-Saturated Heat Carriers, Energoatomizdat, Moscow, 1993.
261. Siromyatnikov, N.I., Vasanova, L.K., and Tuchnin, A.M., Heat transfer in liquid fluidized bed by sub-cooled boiling of liquefied media, Boiling and Condensation, Riga, Vol. 2, pp. 112-119, 1978.
262. Veeman, A.W., and Potze W., Wall-to-liquid heat transfer in a liquid-solid fluidized bed, 6th Heat Transfer Conf., Toronto, Vol. 4, pp. 123-128, 1978.
263. Ipfelkofer R., and Blenke, H., Beitray zum Warmeubergang in Flussigkeits, Friebbettern, Waerme, 84(1), 47-50, 1978.
264. Bologa, M.K., Smirnov, H.F., et al., Heat Transfer by Boiling and Condensation under Electric Field Action, Stiinza, Kishinev, 240 pp., 1987.
265. Smirnov, H.F., Closed heat transferred evaporative systems theory fundamentals, Dissertation thesis, Leningrad, 1979.
266. Kutateladze, S.S., Pool boiling heat transfer crisis hydrodynamic theory, J. Tech. Phys., 20(11), 1389-1392, 1950.
267. Zuber, N., On the stability of boiling heat transfer, Trans. ASME, 80(3), 711-720, 1958.
268. Kutateladze, S.S., Heat Transfer Theory Fundamentals, 5th Issue, Atomizdat., Moscow, 415 pp., 1979.
269. Borishansky, V.M., and Gotovsky, M.A., Two-phase near-wall layer hydraulic stability destroying by pool and forced convection boiling theory, Heat Mass Transfer, Minsk, Sci. Technol., 3, 125-130, 1965.
270. Linchard, J.Ch., and Dhir, V.N., Maximum and minimum heat fluxes by pool boiling hydrodynamic base of calculation, HMT M., 2(Part 1), 273-298, 1972.
271. Kirichenko, Yu.A., and Chernyakov, I.S., First critical heat flux by boiling on flat heaters determination, EPJ, Vol. 20(6), 982-987, 1971.
272. Labuntsov, D.A., Boiling critical heat fluxes top border about, HTT, 10(6), 1337-1338, 1972.
273. Yagov, V.V., and Pusin, V.A., Critical heat flux by forced saturated liquid motion calculation approximated model, Thermal Eng., 3, 2-5, 1985.
274. Kovalev, S.A., and Smirnova, L.F., Fin washed by boiled liquid, temperature field, HTT, 6(4), 698-701, 1968.
275. Kovalev, S.A., and Rubchinskaya, G.B., Boiling on non-isothermal surface heat transfer stability, HTT, 11(1), 117-122, 1973.
276. Isaev, S.I., et al., Heat Transfer Theory, A.I. Leontiev, ed., Moscow Tech. Univ, pp. 684, 1997.
277. Tolubinsky, V.I., Boiling Heat Transfer, Naukova Dumka, Kiev, 316 pp., 1980.
278. Yagov, V.V., and Zudin, Yn.V., Mechanistic model for nucleate boiling crisis at different gravity fields, Heat Transfer. Proc. of the 10th Int. HTC, Brighton, UK, Vol. 5, 189-194, 1994.
279. Haramura, Y., and Katto, Y., A new hydrodynamic model of critical heat flux, applicable widely to both pool and forced convection boiling on submerged bodies in saturated liquid, J. Heat Mass Transfer, 26(3), 389-399, 1983.
280. Katto, Y., A physical approach to critical heat flux of sub-cooled flow boiling in round tubes, J. Heat Mass Transfer, 33(4), 611-620, 1990.
281. Katto, Y., Prediction of critical heat flux of sub-cooled flow boiling in annular tubes, J. Heat Mass Transfer, 33(9), 1921-1928, 1990.
282. Yagov, V.V., Boiling in tubes with saturated and subcooled liquid heat transfer crisis mechanism, Thermal Eng., 5, 16-22, 1992.
283. Celata, G.P., Critical heat flux in water sub-cooled flow boiling, experiments and modeling, Proc. 3rd European Thermal Sciences and 14th UIT National Heat Transfer Conference, May 29-31, Vol. 1, pp. 27-40, 1996.
284. Celata, G.P., Modeling of critical heat flux in subcooled flow boiling, The Physics of Heat Transfer in Boiling and Condensation, May, Moscow, pp. 324-332, 1997.
285. Tong, L.S., Boundary layer analysis of the flow boiling crisis, Proc. of 3rd Int. Heat Trans. Conf. Hemisphere, New York, Vol. 111, pp. 1-6, 1966.
286. Bergles, A.E., Burn out under conditions of subcooled boiling and forced convection, Thermal Eng., 27(1), 48-50, 1980.
287. Smogalev, I.P., Calculation on of Critical heat fluxes with flow of subcooled water at low velocity, Thermal Eng., 28(4), 208-211, 1981.
288. Weisman, I., and Ying, S.H., Theoretically based CHF prediction at low qualities and intermediate flows, Trans. Am. Nucl. Soc., 45, 832-833, 1983.
289. Weisman, I., and Pei, B.S., Prediction of critical heat flux in flow boiling at low qualities, Int. J. Heat Mass Transfer, 26, 1463-1477, 1983.
290. Styrikovich, M.A., Nevstrueva, E.I., and Dvorina, G.M., The effect of two-phase flow pattern on the nature of heat transfer crisis in boiling, Proc. 4th Int. Heat Transfer Conf., Hemisphere, New York, Vol. 9, pp. 360-362, 1970.
291. Celata, G.P., et al., Rationalization of existing mechanistic models for the prediction of water subcooled flow boiling critical heat flux, Int. J. Heat Mass Transfer, 37(Suppl 1), 347-360, 1994.
292. Lee, C.H., and Mudawar, L.A., Mechanistic critical heat flux model for subcooled flow conditions, J. Multiphase Flow, 14, 711-728, 1988.
293. Kafarov, V.V., Heat and Mass Fundamentals, High School, Moscow, 453 pp., 1979.
294. Koba, A.L., et al., Liquid by forced convection inside capillary channels boiling heat transfer critical heat fluxes, Thernal Eng., 6, 73-74, 1980.
295. Kozhelupenko, Yu D., et al., Binary liquids mixtures by forced convection inside capillary channels boiling heat transfer critical heat fluxes investigations, RETP, 3, 90-98, 1981.
296. Kozhelupenko, Yu D., and Koba, A.L., Smirnov, H.F., Binary liquids mixtures by forced convection inside capillary channels heat transfer crisis, Thermal Eng., 1, 66-68, 1983.
297. Kozhelupenko, Yu D., Smirnov, H.F., and Koba, A.L., Subcooled liquids flow inside narrow annular channels by low motion velocity heat transfer crisis, Thermo-Physics and Hydrodynamics by Boiling and Condensation, Riga., Vol. 1, pp. 154-155, 1982.
298. Vasiliev, A.N., and Kirilov, P.L., Boiling in small diameters channels heat transfer crisis, connected with liquid abrupt evaporation investigation, Nuclear Reactors Thermophysical Problems, Atomizdat, Moscow, Vol. 2, pp. 49-57, 1970.
299. Gluschenko, L.F., Subcooled boiling critical heat fluxes experimental data generalization, Thermo-Phys. Thermal Eng., 5, 125-129, 1969.
300. Grigoriev, V.A., Antipov, V.P., and Pavlov, Yu.M., Nitrogen and helium boiling in channels heat transfer experimental investigation, Thermal Eng., 4, 11-14, 1977.
301. Ornatsky, A.P., Main process regime parameters and channel geometry sizes influence on critical heat flux of boiling by forced convection of sub-cooled liquid, Convective Heat Transfer, Kiev, pp. 19-28, 1968.
302. Ornatsky, A.P., and Vinyarsky, L.S., Sub-cooled water forced motion in tubes of small diameters heat transfer crisis, HTT, 3(3), 444-451, 1965.
303. Ornatsky, A.P., and Kichigin, A.M., Critical heat flux dependency on liquid mass velocity, sub-cooling and pressure investigation, Thermal Eng., 2, 75-79, 1961.
304. Ornatsky, A.P., and Kichigin, A.M., Sub-cooled water boiling in tubes of small diameter in high pressure field critical heat fluxes, Thermal Eng., 6, 44-47, 1962.
305. Labuntsov, D.A., Boiling critical heat fluxes by sub-cooled water forced motion, Atomic Power Eng., 10(5), 523-525, 1961.
306. Povarnin, P.I., 96% sub-cooled ethyl alcohol forced flow boiling critical heat fluxes investigation, Thermal Eng., 12, 57-60, 1962.
307. Povarnin, P.I., and Semenov, S.T., Sub-cooled water flow in small diameter tubes by high pressures boiling heat transfer crisis investigation, Thermal Eng., 1, 79-85, 1960.
308. Ribin, R.A., Diameter tube influence on critical heat fluxes by water boiling investigation, EPJ, 6(2), 15-19, 1963.
309. Tolubinsky, V.I., and Motorin, A.S., Binary liquids mixtures by forced convection inside capillary channels heat transfer crisis, HMT M, 2(Part 1), 62-66, 1972.
310. Bernath, L., A theory of local boiling burnout and it’s application to existing data, Chem. Eng. Prog. Symp. Ser., 56(30), 95-116, 1960.
311. Giarratano, P.I., et al., Forced convection heat transfer to liquid helium, J. Adv Cryogenic Eng., 19, 404-409, 1974.
312. Shtokolov, L.S., Ethyl alcohol forced flow boiling heat transfer crisis in high velocities field, EPJ, 12, 3-7, 1964.
313. Lowdermilk, W., Lanzo, C.D., and Siegel, B.L., Investigation of Boiling Burnout and Flow Stability for Water Flowing in Tubes, NASA-TW-4383, 1958.
314. Macbeth, R.V., Burnout analysis. Part 2. The basic burnout curve, U.K. Report AEEW, R-167, Winfrith, 1963.
315. Gomelauri, V.T., Magrakvelidze, T.Sh., and Dvaladze, S.V., Sub-cooling value influence on forced water flow heat transfer crisis by surface with two-dimensional roughness streamline experimental investigation, Commun. Acad. Sci. Georgia, Tbilisi, 85(3), 673-675, 1977.
316. Ornatsky, A.P., et al., Annular channel critical power value changing regularities by high inequality along by length investigation, HMT-V, Minsk, Sci. Technol., 3(Part 2), 21-27, 1976.
317. Ornatsky, A.P., Chernoby, V.A., and Vasiliev, A.F., Heat transfer crisis regularities of flow in annular channels by different heat generation laws, Thermophys. Thermal Eng., 31, 13-14, 1976.
318. Ornatsky, A.P., et al., Annular heat generating channel critical power value experimental definition, Appl. Thermal Eng., 1, 85-88, 1979.
319. Savina, V.N., Water, glycol and antifreeze-65 forced flow in annular channels heat transfer crisis values and hydraulic resistance investigation, Dissertation thesis, Kiev Nat. Polyt. Univ., 1971.
320. Sterman, L.S., and Checheta, P.G., Organic liquids in coaxial annular channels critical heat fluxes, HMT-4, M., 2, 315-321, 1972.
321. Tolubinsky, V.I., et al., Boiling heat transfer crisis in concentric and eccentric annular channels and slits, HMT-2, M., 3(part 2), 315-321, 1967.
322. Tolubinsky, V.I., Litoshenko, A.I., and Shevzov, A.L., Critical heat fluxes in annular channels experimental data generalization, Heat Mass Transfer, Minsk, 2, 315-321, 1968.
323. Tolubinsky, V.I., Ornatsky, A.P., and Litoshenko, A.I., Sub-cooling in narrow annular channels heat transfer crisis, Heat Transfer by Phase Change, Kiev, 1966, pp. 17-24.
324. Chirkin, V.S., and Yukin, V.P., Flow boiled liquid in annular gap heat transfer (heat removal) crisis, J. Techn. Phys., 26(7), 1542-1555, 1965.
325. Shah, M.K., A general correlation for critical heat flux in Annuly, Int. J. HMT, 23(2), 225-234, 1980.
326. Alekseev, G.V., Zenkevich, B.A., and Subbotin, V.I., Experimental Data of critical heat fluxes by boiling in annular channels, Boiling crisis and evaporative heating surfaces temperature regimes, Leningrad, ZKTI, 58, 91-98, 1965.
327. Doroshuk, V.E., and Lanzman, V.P., Channel diameter influence on critical heat fluxes, Thermal Eng., 8, 1963.
328. Miropolsky, Z.L., and Shizman, M.E., Water boiling in channels critical heat fluxes, Nucl. Power Eng., 2(6), 515-521, 1961.
329. Kronin, I.V., Pokhvalov, Yu.E., and Voskresensky, K.D., Water forced flow critical heat fluxes study, Nuclear Reactors Thermo-Physics Problems, Atomizdat, Moscow, 3, pp. 32-38, 1971.
330. Smolin, V.N., Polyakov, V.K., and Esikov, V.N., Heat transfer crisis experimental investigation, Nucl. Power Eng., 5, 417-422, 1964.
331. Styricovich, M.A. (Ed), Water boiling by flow in cylindrical channels heat transfer crisis calculation recommendations Scientific Council of complex problem. Thermophysics, Ser. HMT., Preprint 1-57. High Tem. In. of Acad. of Sci. of USSR, 67 pp., 1980.
332. Ivashkevich, A.A., Liquid forced flow boiling heat transfer coefficients and critical heat fluxes, Thermal Eng., 10, 74-78, 1961.
333. Chigareva, T.S., and Chigarev, N.V., Binary mixtures characteristic peculiarities and theoretical imaginations of their explanations, Boiling Physics Investigation, Stavropol, Iss. 5, pp. 21-35, 1979.
334. Ornatsky, A.P., et al., Heat transfer crisis by forced flow boiling in annular channels experimental data generalization experience with using only liquid inlet parameters, Thermo-Phys. Thermal Eng., 26, 33-38, 1974.
335. Sterman, L.S., et al., Organic heat carriers forced flow in tubes and pool boiling critical heat fluxes, HMT, Minsk., P-E., 1-29, 1964.
336. Ornatsky, A.P., Chernoby, V.A., and Savina, V.N., Water, glycol and antifreeze-65 sub-cooled forced flow in annular channels heat transfer crisis values study, RETP, 2, 86-91, 1970.
337. Katto, Y., Ishkoya, S., and Teraoka, K., Bubble and transient boiling in narrow media between two parallel disks, Nichon Kikay Gakkay Rombuncyu, 42(361) 2854-2861.
338. Katto, Y., and Shoji, M., Microlayer and bubble growth in pool boiling, J. Heat Mass Transfer, 12(N8), 1969.
339. Afanasiev, B.A., and Smirnov, H.F., Heat Transfer crisis hydrodynamic theory, modified for vaporization on surfaces covered by capillary-porous structures, Russia Nation, 1st HMTC, Moscow, Vol. 4, pp. 13-18, 1994.
340. Afanasiev, B.A., and Smirnov, H.F., The boiling crisis phenomenon on capillary porous covering. MTD-Vob. 309. National Heat Transfer Conference, ASME, Vol. 7, pp. 17-21, 1995.
341. Afanasiev, B.A., Vinogradova, E.P., and Smirnov, H.F., Crisis phenomenon by vaporization in screen capillary-porous coatings and artery structures of heat pipes, EPJ, 48(4), 607-614, 1985.
342. Smirnov, H.F., et al., Limiting characteristics of low-temperature heat pipes by discontinuous heat input, RETP, 2, 8-15, 1987.
343. Bezrodny, M.K., Volkov, S.S., and Moklyak, V.F., Two-Phase Thermo-Siphons in Industrial Thermal Engineering, High School, Kiev, 76 pp., 1991.
344. Smirnov, H.F., and Afanasiev, B.A., The crisis phenomenon when vaporization take place on surfaces covered porous structure, 9th IHPC Preprints, Albuquerque, May 1995.
345. Petukhov, B.S., Zukov, V.M., and Shildkret, V.M., Helium forced flow boiling heat transfer crisis investigation, Heat Transfer and Hydrodynamic by Boiling and Condensation, Coll. of Works., Novos, pp. 220-226, 1979.
346. Krieth, F., and Bohn, S.M., Principles of Heat Transfer, 5th ed., 720 pp. + 74 Appendixes, 1993.
347. Arefiev, K.M., and Gnedina, E.A., Forced flow sub-cooled liquid critical heat fluxes experimental data generalization, Boiling Crisis and Heating Evaporative Surfaces Temperature Regimes, pp. 191-200 (Works of ZKTI; Iss. 58), 1965.
348. Dann, P., and Reay, D., Heat Pipes, Energy, Moscow, 272 pp., 1979.
349. Ivanovsky, M.N., Sorokin, V.I., and Yagodkin, I.V., Heat Pipes Physical Fundamentals, Energoatomizdat, Moscow, 252 pp., 1987.
350. Styrikovich, M.A., Polonsky, V.S., and Ziklauri, G.V., Heat Mass Transfer and Hydrodynamic at Two-Phase Flows of Nuclear Power Stations, Nauka, Moscow, 368 pp., 1982.
351. Krukov, A.P., Kinetic analysis of evaporation and condensing processes on the surface, Paper collect, “Kinetic Theory of Transfer Processes When Evaporation and Condensing,” Paper of International Seminar, Minsk, 1991, Belarus Academy of Science, Institute of Heat-and-Mass Exchange, pp. 3-21.
352. Labuntzov, R.A., and Krukov, A.P., Intensive evaporation processes, Teploenergetika, 4, 8-11, 1977.
353. Labuntzov, R.A., and Krukov, A.P., Analysis of intensive evaporation and condensing, Int. J. Heat Mass Transfer, 22, 989-1002, 1979.
354. North, M.T., Shaubakh, R.M., and Rosenfeld, I.H., Liquid film evaporation from bidisperse capillary wicks in heat pipe evaporators, Proc. 9th Int. Heat Pipe Conf., Albuquerque, NM, May 1-5, 1995.
355. Rosenfeld, I.H., Anderson, W.G., and North, M.T., Improved high heat flux loop heat pipes using bidisperse evaporators wicks, 10th IHPC, September, Stuttgart Preprints session, A1, pp. 5-6, 1997.
356. Maidanik, Yu.F., Vershinin, S.V., and Fershtater Yu.G., Heat transfer enhancement in a loop heat pipe evaporator, 10th IHPC, September, Stuttgart Preprints session, A1 Paper, A1, pp. 3-6, 1997.
357. Kiseev, V.M., and Pogorelov, N.P., A study of loop heat pipe thermal resistance, 10th IHPC, September, Stuttgart Preprints session, A1, Paper A1, pp. 6-9, 1997.
358. Gerasimov, Yu.F., et al., Low temperature heat pipe with segregated vapor and liquid lines, TVT, 12(5), 1131-1134, 1974.
359. Gerasimov, Yu.F., et al., Low temperature heat pipe with segregated vapor and liquid lines, Inst. Liquid Phys., 28(6), 957-960, 1975.
360. Gerasimov, Yu.F., et al., Some investigation results obtained for low temperature heat pipes operating against gravity forces, Inst. Liquid Phys., 30(4), 581-586, 1976.
361. Demidov, A.S., and Yatsenko, Eu.S., Investigation of heat and mass transfer in the evaporation zone of a heat pipe operating by the “inverted meniscus” principle, Int. J. Heat Mass Transfer, 37, 2155-2163, 1994.
362. Faghri, A., Heat Pipe Science and Technology, Taylor & Francis, 874 pp., 1994
363. Silverstein, C., Design and Technology of Heat Pipes for Cooling and Heat Exchange, Taylor & Francis, Washington, D.C., 368 pp., 1992.
364. Peterson, J.P., Introduction to Heat Pipes: Modeling, Testing and Application, John Wiley and Sons, New York, 1994.