Component test for simulation of piston ring – Cylinder liner friction at realistic speeds

Tribology International

Volumn 104, Issue , 2016, Pages 57-63

  Söderfjäll, Markus ^a   Almqvist, Andreas ^a   Larsson, Roland ^a  

^a LULEÅ UNIVERSITY OF TECHNOLOGY   (Sweden)

Author keywords

Cylinder liner; Heavy duty diesel engine; Piston ring friction; Tribometer

Indexed keywords

ENGINE CYLINDERS; ENGINE PISTONS; ENGINES; EQUIPMENT TESTING; FRICTION; INTERNAL COMBUSTION ENGINES; PISTON RINGS; PISTONS; TRIBOLOGY;

CYLINDER LINERS; FRICTIONAL LOSS; HEAVY-DUTY DIESEL ENGINE; MECHANICAL FRICTION; NOVEL COMPONENT; PISTON RING FRICTION; TRIBOMETERS; TWIN-LAND OIL CONTROL;

DIESEL ENGINES;

EID: 84984671979     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2016.08.021     Document Type: Article

References (23)

1. [1] Richardson, D.E., Review of power cylinder friction for diesel engines. J Eng Gas Turbines Power 122:4 (2000), 506–519.
2. [2] Priest, M., Dowson, D., Taylor, C.M., Theoretical modelling of cavitation in piston ring lubrication. Proc Inst Mech Eng Part C: J Mech Eng Sci 214:3 (2000), 435–446.
3. [3] Ting LL. Development of a reciprocating test rig for tribological studies of piston engine moving components – part I: rig design and piston ring friction coefficients measuring method. Technical report. SAE Technical Paper; 1993.
4. [4] Hill, Stephen H., Hartfield-Wünsch, Susan E., Tung, Simon C., Bench wear testing of common gasoline engine cylinder bore surface/piston ring combinations. Tribol Trans 39:4 (1996), 929–935.
5. [5] Dellis, P.S., Effect of friction force between piston rings and liner: a parametric study of speed, load, temperature, piston-ring curvature, and high-temperature, high-shear viscosity. Proc Inst Mech Eng Part J: J Eng Tribol 224:5 (2010), 411–426.
6. [6] Dearlove Janice, Cheng Wai K. Simultaneous piston ring friction and oil film thickness measurements in a reciprocating test rig. Technical report. SAE Technical Paper; 1995.
7. [7] Akalin Ozgen, Newaz Golam M. A new experimental technique for friction simulation in automotive piston ring and cylinder liners. Technical report. SAE Technical Paper; 1998.
8. [8] Bolander, N.W., Steenwyk, B.D., Sadeghi, F., Gerber, G.R., Lubrication regime transitions at the piston ring–cylinder liner interface. Proc Inst Mech Eng Part J: J Eng Tribol 219:1 (2005), 19–31.
9. [9] Spencer, Andrew, Avan, Emin Yusuf, Almqvist, Andreas, Dwyer-Joyce, Rob S., Larsson, Roland, An experimental and numerical investigation of frictional losses and film thickness for four cylinder liner variants for a heavy duty diesel engine. Proc Inst Mech Eng Part J: J Eng Tribol 227:12 (2013), 1319–1333.
10. [10] Johansson, Staffan, Nilsson, Per H., Ohlsson, Robert, Rosen, Bengt-Göan, Experimental friction evaluation of cylinder liner/piston ring contact. Wear 271:34 (2011), 625–633 [The 12th international conference on metrology and properties of engineering surfaces].
11. [11] Obert, Petra, Müller, Torben, Füßer, Hans-Jürgen, Bartel, Dirk, The influence of oil supply and cylinder liner temperature on friction, wear and scuffing behavior of piston ring cylinder liner contacts – a new model test. Tribol Int 94 (2016), 306–314.
12. [12] Olander, Petra, Jacobson, Staffan, Scuffing resistance testing of piston ring materials for marine two-stroke diesel engines and mapping of the operating mechanisms. Wear 330 (2015), 42–48.
13. [13] Furuhama Shoichi, Sasaki Shinichi. New device for the measurement of piston frictional forces in small engines. Technical report. SAE Technical Paper; 1983.
14. [14] Kikuchi, Takashi, Ito, Shinichiro, Nakayama, Yoshinori, Piston friction analysis using a direct-injection single-cylinder gasoline engine. JSAE Rev 24:1 (2003), 53–58.
15. [15] Kohashi Ken-ichi, Kimura Yuichiro, Murakami Motoichi, Drouvin Yann. Analysis of piston friction in internal combustion engine. Technical report. SAE Technical Paper; 2013.
16. [16] Kunkel, Sebastian, Werner, Martin, Wachtmeister, Georg, Setting up a measuring device to determine the friction of the piston assembly. SAE Int J Mater Manuf 4:2011-01-0227 (2011), 340–351.
17. [17] Gore, Michael, Theaker, Michael, Howell-Smith, Sebastian, Rahnejat, Homer, King, Paul D., Direct measurement of piston friction of internal-combustion engines using the floating-liner principle. Proc Inst Mech Eng Part D: J Automob Eng 228:3 (2014), 344–354.
18. [18] Law Theo, MacMillan David, Shayler Paul J, Kirk Geoff, Pegg Ian, Stark Roland. A new floating-liner test rig design to investigate factors influencing piston-liner friction. Technical report. SAE Technical Paper; 2012.
19. [19] Liao Kai, Chen Haijie, Tian Tian. The study of friction between piston ring and different cylinder liners using floating liner engine – part 1. SAE Technical Paper; April 2012.
20. [20] Chen Haijie, Liao Kai, Tian Tian. A numerical and experimental study of twin-land oil control ring friction in internal combustion engines part 2. SAE Technical Paper; April 2012.
21. [21] Sato Oki, Takiguchi Masaaki, Takayuki Aihara, Seki Yulchi, Fujimura Kazuhiro, Tateishi Yukio. Improvement of piston lubrication in a diesel engine by means of cylinder surface roughness. Technical report. SAE Technical Paper; 2004.
22. [22] Kirner, C., Halbhuber, J., Uhlig, B., Oliva, A., Graf, S., Wachtmeister, G., Experimental and simulative research advances in the piston assembly of an internal combustion engine. Tribol Int 99 (2016), 159–168.
23. [23] Larsson Tor, Bergstrom Kjell ac, Hinderman Terry, Hauptmann Lars-Gustaf, Wennstrom Lars, Denbratt Ingemar, et al. The volvo 3-litre 6-cylinder engine with 4-valve technology. Technical report. SAE Technical Paper; 1990.