Particles impact characteristics on cutting surface during the abrasive water jet machining: Numerical study

Journal of Materials Processing Technology

Volumn 232, Issue , 2016, Pages 116-130

  Ahmed, Dewan Hasan ^a   Naser, Jamal ^a   Deam, Rowan Thomas ^a  

^a SWINBURNE UNIVERSITY OF TECHNOLOGY   (Australia)

Author keywords

Abrasive water jet; CFD; Erosion; Particle impact

Indexed keywords

ABRASIVES; COMPUTATIONAL FLUID DYNAMICS; CUTTING TOOLS; EROSION; JETS;

ABRASIVE PARTICLES; ABRASIVE WATER JET; ABRASIVE WATER JET MACHINING; CUTTING PERFORMANCE; DISTRIBUTION FACTOR; PARTICLE IMPACT; RADII OF CURVATURE; RADIUS OF CURVATURE;

FIGHTER AIRCRAFT;

EID: 84977489332     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2016.01.032     Document Type: Article

References (35)

1. Ahmadi-Brooghani, S.Y., Hassanzadeh, H., Kahhal, P., Modeling of single-particle impact in abrasive water jet machining. Int. J. Mech. Syst. Sci. Eng. 1:4 (2007), 231–236.
2. Anwar, S., Axinte, D.A., Becker, A.A., Finite element modelling of a single-particle impact during abrasive waterjet milling. Proc. IMechE J: J. Eng. Tribol. 225 (2011), 821–932.
3. Anwer, M., So, R.M.C., Lai, Y.G., Perturbation by and recovery from bend curvature of a fully developed turbulent flow. Phys. Fluids A 1 (1989), 1387–1397.
4. Bitter, J.G.A., A study of erosion phenomena—part І. Wear 6 (1963), 5–21.
5. Bitter, J.G.A., A study of erosion Phenomena—part II. Wear 6 (1963), 169–190.
6. CFX, Solver Manual CFX-4.2. 1997, AEA Technology plc.
7. Deam, R.T., Lemma, E., Ahmed, D.H., Modelling of the abrasive water jet cutting process. Wear 257 (2004), 877–891.
8. Dutta, P., Nandi, N., Effect of reynolds number and curvature ratio on single phase turbulent flow in pipe bends. Mech. Mech. Eng. 19:1 (2015), 5–16.
9. El-Domiaty, A.A., Shabara, M.A., Abdel-Rahman, A.A., Al-Sabeeh, A.K., On the modelling of abrasive waterjet cutting. Int. J. Adv. Manuf. Technol. 12:4 (1996), 255–265.
10. Finnie, I., Some observations on the erosion of ductile metals. Wear 19 (1972), 81–90.
11. Gudimetla, P., Yarlagadda, P.K.D.V., Finite element analysis of the interaction between an AWJ particle and a polycrystalline alumina ceramic. J. Achiev. Mater. Manuf. Eng. 27:1 (2007), 7–14.
12. Hashish, M., Wear modes in abrasive waterjet machining. Tribol. Aspects Manuf.: ASME, 1991, 141–153 (PED—vol. 54/TRIB—vol. 2).
13. Hashish, M., The effect of beam angle in abrasive-waterjet machining. J. Eng. Ind.: Trans. ASME 115 (1993), 51–56.
14. Johnson, K.L., Contact Mechanics. 1987, Cambridge University Press, New York.
15. Junkar, M., Jurisevic, B., Fajdiga, M., Grah, M., Finite element analysis of single-particle impact in abrasive water jet machining. Int. J. Impact Eng. 32:7 (2006), 1095–1112.
16. Kitamura, M., Ishikawa, M., Sudo, K., Yamaguchi, Y., Ishimura, T., Tujita, K., Cutting of steam turbine components using abrasive waterjet. 11th International Conference on Jet Cutting Technology, St. Andrews, Scotland, 1992, 543–554.
17. Kumar, N., Shukla, M., Finite element analysis of multi-particle impact on erosion in abrasive water jet machining of titanium alloy. J. Comput. Appl. Math. 236 (2012), 4600–4610.
18. Lebar, A., Junkar, M., Simulation of abrasive water jet cutting process: part 1. Unit event approach. Model. Simul. Mater. Sci. Eng. 12 (2004), 1159–1170.
19. Leu, M.C., Meng, P., Geskin, E.S., Tismeneskiy, L., Mathematical modeling and experimental verification of stationary waterjets cleaning process. Trans. ASME: J. Manuf. Sci. Eng. 120 (1998), 571–579.
20. Li, W.Y., Wang, J., Zhu, H., Li, H., Huang, C., On ultrahigh velocity micro-particle impact on steels—a single impact study. Wear 305:1–2 (2013), 216–227.
21. Li, W.Y., Wang, J., Zhu, H., Huang, C., On ultrahigh velocity micro-particle impact on steels—a multiple impact study. Wear 309:1–2 (2014), 52–64.
22. Liu, H., Wang, J., Brown, R.J., Kelson, N., Computational Fluid Dynamics (CFD) simulation of ultrahigh velocity abrasive waterjet. Key Eng. Mater. 233–236 (2003), 477–482.
23. Liu, H., Wang, J., Kelson, N., Brown, R.J., A study of abrasive water jet characteristics by CFD simulation. J. Mater. Process. Technol. 153–154 (2004), 488–493.
24. Lv, Z., Huang, C., Zhu, H., Wang, J., Yao, P., Liu, Z., FEM analysis on the abrasive erosion process in ultrasonic-assisted abrasive waterjet machining. Int. J. Adv. Manuf. Technol. 78 (2015), 1641–1649.
25. Mabrouki, T., Raissi, K., Cornier, A., Numerical simulation and experimental study of the interaction between a pure high-velocity waterjet and targets: contribution to investigate the decoating process. Wear 239 (2000), 260–273.
26. Maniadaki, K., Kestis, T., Bilalis, N., Αntoniadis, A., Finite element based model for pure waterjet process simulation. Int. J. Adv. Manuf. Technol. 31:9–10 (2007), 933–940.
27. Maniadaki, K., Bilalis, N., Αntoniadis, A., Effect of impact angle and velocity in crater circularity in abrasive water jet machining by means of multi-particle impact simulation. Int. J. Mach. Mach. Mater. 10:1–2 (2011), 34–47.
28. Meng, P., Geskin, E.S., Leu, M.C., Li, F., Tismenseskiy, L., An analytical and experimental study of cleaning with moving waterjets. Trans. ASME: J. Manuf. Sci. Eng. 120 (1998), 580–589.
29. Mostofa, M.G., Kil, K.Y., Hwan, A.J., Computational fluid analysis of abrasive waterjet cutting head. J. Mech. Sci. Technol. 24 (2010), 249–252.
30. Preece, C., Teatise on material science and technology. Erossion, vol. 16, 1979, Academic press, New York, 69–126.
31. Srinivasa, P.R., Ramulu, M., Predicting hydro-abrasive erosive wear during abrasive water jet cutting: part I—a mechanistic formulation and its solution. Manuf. Sci. Eng.: ASME 1 (1994), 339–351 (PED—vol. 68-1).
32. Takaffoli, M., Papini, M., Numerical simulation of solid particle impacts on Al6061-T6 part I: three-dimensional representation of angular particles. Wear 292–293 (2012), 100–110.
33. Takaffoli, M., Papini, M., Numerical simulation of solid particle impacts on Al6061-T6 part II: materials removal mechanisms for impact of multiple angular particles. Wear 296:1–2 (2012), 648–655.
34. Turenne, S., Fiset, M., Modeling of abrasive particle trajectories during erosion by a slurry jet. Wear 162–164 (1993), 679–687.
35. Zeng, J., Kim, J.T., An erosion model of polycrystalline ceramics in abrasive waterjet cutting. Wear 193 (1996), 207–217.