Numerical flow analysis of a centrifugal compressor with ported and without ported shroud

SAE Technical Papers

Volumn 1, Issue , 2014, Pages

  Semlitsch, Bernhard ^a   Jyothishkumar, V ^a   Mihaescu, Mihai ^a   Fuchs, Laszlo ^a   Gutmark, Ephraim ^b   Gancedo, Matthieu ^b  

^a ROYAL INSTITUTE OF TECHNOLOGY   (Sweden)

^b UNIVERSITY OF CINCINNATI   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CENTRIFUGATION; FLOW FIELDS; INTERNAL COMBUSTION ENGINES; LARGE EDDY SIMULATION; SUPERCHARGERS; TURBOMACHINERY; VELOCITY MEASUREMENT;

AUTOMOTIVE TURBOCHARGERS; COMPRESSOR EFFICIENCY; COMPUTATIONAL RESULTS; EXPERIMENTAL INVESTIGATIONS; NUMERICAL FLOW ANALYSIS; PARTICLE IMAGE VELOCIMETRIES; PERFORMANCE PARAMETERS; SLIDING MESH TECHNIQUE;

CENTRIFUGAL COMPRESSORS;

EID: 84899545883     PISSN: 01487191     EISSN: 26883627     Source Type: Journal    
DOI: 10.4271/2014-01-1655     Document Type: Conference Paper

References (21)

1. Rodgers, C., " Centrifugal Compressor Inlet Guide Vanes for Increased Surge Margin," J. Turbomach. 113 (4): 696-702, 1991, doi: 10.1115/1.2929136.
2. Whitfield, A., and Abdullah, A.H., " The Performance of a Centrifugal Compressor with High Inlet Prewhirl," J. Turbomach. 120 (3): 487-493, 1998, doi: 10.1115/1.2841744.
3. Ishida, M., Sakaguchi, D., and Ueki, H., 2006, " Effect of Pre-swirl on Unstable Flow Suppression in a Centrifugal Impeller With Ring Groove Arrangement," ASME Turbo Expo GT2006-90400, 2006, doi: 10.1115/GT2006- 90400.
4. Barton, M. T., Mansour, M. L., Liu, J. S., and Palmer, D. L., " Numerical Optimization of a Vaned Shroud Design for Increased Operability Margin in Modern Centrifugal Compressors," J. Turbomach. 128: 627-631, 2004, doi: 10.1115/1.2187526.
5. Saha, S. L., Kurokawa, J., Matsui, J., and Imamura, H., " Passive Control of Rotating Stall in a Parallel-Wall Vaned Diffuser by J-Grooves," J. Fluids Eng. 123 (3): 507-515, 2001.
6. Macdougal, I., and Elder, R. L., " The Improvement of Operating Range in a Small, High Speed, Centrifugal Compressor Using Casing Treatment," IMechE Conference on Turbochargers and Turbocharing C32/82, 1982.
7. th IMechE International Conference on Turbocharger and Turbocharging, London C602/016/2002, May 14-15, 2002.
8. Zheng, X., Zhang, Y., Yang, M., Bamba, T., and Tamaki, H., " Stability Improvement of High-Pressure-Ratio Turbocharger Centrifugal Compressor by Asymmetrical Flow Control-Part II: Nonaxisymmetrical Self-Recirculation Casing Treatment," J. Turbomach. 135 (2): 021007-1-021007-8, 2002, doi: 10.1115/1.4006637.
9. Sivagnanasundaram Subenuka, Spence Stephen, Early Juliana and Nikpour Bahram., " An impact of Various Shroud Bleed Slot configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field " J. of Turbomach. 135 (4), 2013, doi: 10.1115/1.4007513.
10. Ishida, M., Sakaguchi, D., and Ueki, H., " Effect of pre-swirl on unstable flow suppression in a centrifugal impeller with ring groove arrangement " ASME Turbo Expo GT2006-90400, 2006, doi: 10.1115/GT2006-90400.
11. Hellström, F., Gutmark, G., and Fuchs, L., " Large Eddy Simulation of the Unsteady flow in a Radial Compressor Operating Near Surge," J. of Turbomach. 134 (5): 1157-1169, 2012, doi: 10.1115/1.4003816.
12. Guleren, K.M., Afgan, I., and Turan, A., " Predictions of Turbulent Flow for the Impeller of a NASA Low-Speed Centrifugal Compressor," J. Turbomach. 132 (2): 021005-1-021005-8, 2010, doi: 10.1115/1.3140824.
13. Fisher, F., " Application of Map Width Enhancement Devices to Turbocharger Compressor Stages," SAE Technical Paper 880794, 1988, doi: 10.4271/880794.
14. Hunziker, R., Dickmann, H. P., and Emmrich, R., " Numerical and Experimental Investigation of a Centrifugal Compressor with an Inducer Casing Bleed System," J. Power Energy, 215 (6): 783-791, 2001.
15. Guleren, K.M., Turan, A., and Pinarbasi A., " Large Eddy Simulation of the flow in a Low-Speed Centrifgual Compressor," Int. J. Numerical Methods in Fluids, 56: 1271-1280, 2008, doi: 10.1002/fld.1741.
16. Chow, P., Cross, M., and Pericleous, K., " A natural extension of the conventional finite volume method into polygonal unstructured meshes for CFD application," Appl. Math. Modelling 20 (2): 170-183, 1996, doi: 10.1016/0307-904X(95)00156-E.
17. STARCCM+, Commercial code, Ver. 6.06, CD-adapco, Melville, NY (1987).
18. Guillou, E., Gancedo, M., Gutmark, E., and Mohamed, A., " PIV investigation of the flow induced by a passive surge control method in a radial compressor," Experiments in Fluids, 53 (3): 619-635, 2012.
19. Guillou, E., DiMicco, R., Gutmark, E., Mohamed, A. et al., " Characterization of a Ported Shroud Compressor using PIV Measurements," SAE Technical Paper 2010-01-1225, 2010, doi: 10.4271/2010-01-1225.
20. Sun, Z., Tan, C., and Zhang, D., " Flow field structures of impeller backside cavity and its influence on the centrifugal compressor," Proceedings of ASME TurboExpo, June 8-12, USA, 2009
21. Chen, H., and Lei, V., " Casing Treatment and Inlet Swirl of Centrifugal Compressors," J. of Turbomach, 135 (4): 041010-1-041010-8, 2013, doi: 10.1115/1.4007739.