Optimization of machining parameters in the abrasive waterjet turning of alumina ceramic based on the response surface methodology

International Journal of Advanced Manufacturing Technology

Volumn 71, Issue 9-12, 2014, Pages 2107-2114

  Yue, Zhongbo ^a   Huang, Chuanzhen ^a   Zhu, Hongtao ^a   Wang, Jun ^a   Yao, Peng ^a   Liu, Zengwen ^a  

^a SHANDONG UNIVERSITY   (China)

Author keywords

Abrasive waterjet (AWJ); Ceramic materials; Material removal rate (MRR); Response surface methodology (RSM); Turning

Indexed keywords

ABRASIVES; ALUMINA; CERAMIC MATERIALS; SURFACE PROPERTIES; SURFACE ROUGHNESS; TURNING;

ABRASIVE MASS FLOW RATE; ABRASIVE WATER-JET; CENTRAL COMPOSITE DESIGNS; EXPERIMENTAL INVESTIGATIONS; INFLUENCE OF PROCESS PARAMETERS; MATERIAL REMOVAL RATE; RESPONSE SURFACE METHODOLOGY; SEQUENTIAL APPROXIMATION;

OPTIMIZATION;

EID: 84899110743     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-014-5624-y     Document Type: Article

References (22)

1. Wilfrid K, Matthias P (1989) Precision machining of advanced ceramics. Am Ceram Soc Bull 68:550-555
2. Kovacevic R, Hashish M, Mohan R, Ramulu M, Kim TJ, Geskin ES (1997) State of the art of research and development in abrasive waterjet machining. J Manuf Sci Eng 119:776-785
3. Wang J (2003) Abrasive waterjet machining of engineering materials. Trans Tech Publications, Uetikon-Zuerich
4. Hashish M (1987) Turning with abrasive waterjets - a first investigation. Trans ASME J Eng Ind 109:281-290
5. Wang J (1999) Abrasive waterjet machining of polymer matrix composites - cutting performance, erosive process and predictive models. Int J Adv Manuf Technol 15:757-768
6. Ansari AI (1991) A study on turning with abrasive waterjets. PhD Diss., Michigan Tech. Univ., Houghton, MI
7. Ansari AI, Hashish M (1995) Effect of abrasive waterjet parameters on volume removal trends in turning. Trans ASME J Eng Ind 117:475-484
8. Manu R, Babu NR (2008) Influence of jet impact angle on part geometry in abrasive waterjet turning of aluminium alloys. Int J Mach Mach Mater 3:120-132
9. Ansari AI, Hashish M, Ohadi MM (1992) Flow visualization study of the macromechanics of abrasive-waterjet turning. Exp Mech 32:358-364
10. Manu R, Babu NR (2009) An erosion-based model for abrasive waterjet turning of ductile materials. Wear 266:1091-1097
11. El-Domiaty AA, Shabara MA, Abdel-Rahman AA, Al-Sabeeh AK (1996) On the modeling of abrasive waterjet cutting. Int J Adv Manuf Technol 12:255-265
12. Zohoor M, Zohourkari I (2011) Modeling of abrasive waterjet turning. Aust J Basic Appl Sci 5(8):70-79
13. Li W, Wang J, Ali YM (2011) An experimental study of radial-mode abrasive waterjet turning of steels. Mater Sci Forum 697-698:166-170
14. Oktem H, Erzurumlu T, Kurtaran H (2005) Application of response surface methodology in the optimization of cutting conditions for surface roughness. J Mater Process Technol 170:11-16
15. Alauddin M, El Baradie MA (1997) Hashmi MSJ (1997) Prediction of tool life in end milling by response surface methodology. J Mater Process Technol 71:456-465
16. Puri AB, Bhattacharyya B (2005) Modeling and analysis of white layer depth in a wire-cut EDM process through response surface methodology. Int J Adv Manuf Technol 25:301-307
17. Design-Expert Software, Version 8, User's Guide, Technical Manual (2000) Stat-Ease Inc., Minneapolis, MN
18. Lebar A, Junkar M (2003) Simulation of abrasive waterjet machining based on unit event features. Proc IME B J Eng Manufact 217(B5):699-703
19. Henning A, Westkamper E (2003) Modeling of wear mechanisms at the abrasive waterjet cutting front, in: Proceedings of the 2003 WJTA American Waterjet Conference, Houston, Texas, USA
20. Hashish M (1988) Visualization of the abrasive-waterjet cutting process. Exp Mech 28:159-169
21. Sheldon GL, Finnie I (1966) On the ductile behaviour of nominally brittle materials during erosive cutting. J Eng Ind 88:387-392
22. Hashish M (1989) Pressure effects in AWJ machining. Trans ASME J Eng Ind 111:1-13