A parallely actuated work support module for reconfigurable machining systems

Proceedings of the ASME Design Engineering Technical Conference

Volumn 1B-1998, Issue , 1998, Pages

  Gopalakrishnan, Venkat ^a   Kota, Sridhar ^a  

^a UNIVERSITY OF MICHIGAN   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COST EFFECTIVENESS; CYLINDER HEADS; DEGREES OF FREEDOM (MECHANICS); INVERSE KINEMATICS; MACHINING; MECHANISMS; PRODUCT DESIGN;

ACTUATED MECHANISMS; AUTOMOTIVE CYLINDERS; ESSENTIAL CHARACTERISTIC; MACHINE SET-UP TIME; NUMBER OF DEGREES OF FREEDOM; PERFORMANCE CRITERION; RECONFIGURABLE MACHINE TOOL; RECONFIGURABLE MACHINING SYSTEMS;

MACHINE TOOLS;

EID: 84892320305     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1115/DETC98/MECH-5959     Document Type: Conference Paper

References (17)

1. Arai, T., Tanikawa, T., Merlet, J.P. and Sendai,T., 1996, "Development of a new parallel manipulator with fixed linear actuator", Japan/USA Symposium on flexible Automation, Vol. 1, pp. 145-149.
2. Aronson, R.B. ed., 1997, "Hexapods: Hot or Ho Hum", Manufacturing Engineering, Vol. 119, No. 4, p. 60.
3. Cooke, A.V. et al., 1995, "Advanced reconfigurable machine for flexible fabrication", Proceedings of SPIE, Vol. 2447, pp. 102-114.
4. Gosselin, C.M., Sefrioui, J. and Richard, M.J., 1992, "On the direct kinematics of general spherical three degree-offreedom parallel manipulators", Robotics, Spacial Mechanisms and Mechanical Systems, Vol. 45, pp. 7-11.
5. Grodzinski,P. and M'Ewens, E., 1954, "Link mechanisms in modern kinematics", Proceedings of the Institution of Mechanical Engineers, Vol. 168, No. 37, p. 877.
6. Khasawneh, B.S. and Ferriera, P.M., 1997, "On using parallel link manipulators as machine tools", Transactions of NAMRI/SME, Vol. XXV, pp. 305-310.
7. Khatib, O. and Bowling, A., 1996, "Optimization of the inertial and acceleration characteristics of manipulators", Proceedings of the IEEE International Conference on Robotics and Automation, Vol. 4, pp. 2883-2889.
8. Lee, K.M. and Shah, D.K., 1988, "Dynamic analysis of a three degree of freedom in parallel actuated manipulator", IEEE Journal of Robotics and Automation, Vol. 4, No. 3, pp. 361-367.
9. Liu, K. et al., 1993, "Kinematic analysis of Stewart platform manipulators", IEEE Transactions of Industrial Electronics, Vol. 40, No.2, pp. 282-293.
10. Merlet, J.P., 1996, "Direct kinematics of planar parallel manipulators", Proceedings of the IEEE International Conference on Robotics and Automation, Vol. 4, pp. 3744-3749.
11. Merlet, J.P., 1996, "Workspace oriented methodology for designing a parallel manipulator", Proceedings of the IEEE International Conference on Robotics and Automation, Vol. 4, pp. 3726-3731.
12. Stewart, D., 1965, "A platform with six degrees of freedom", Proceedings of the Institution of Mechanical Engineers, Vol. 180, Pt. 1, No. 15, pp. 371-386.
13. Stoughton, R. and Arai, T., 1992, "Design and kinematic optimization of parallel manipulators", Bulletin of Mechanical Engineering Laboratory, Agency of Industrial Science and Technology, No. 58, pp.1-17.
14. Tsai, L.W., Walsh, G.C. and Stamper, R.E., 1996, "Kinematics of a novel three DOF translational platform", Proceedings of the IEEE International Conference on Robotics and Automation, Vol. 4, pp. 3446-3451.
15. Wang, J. and Gosselin, C.M., 1996, "Kinematic analysis and singularity loci of spatial four-degree-of-freedom parallel manipulators", Proceedings of the ASME Design Engineering Technical Conference and Computers in Engineering Conference, MECH: 1006, pp. 1-12.
16. Wang, Q.Y., Zou, M.Y. and Li, Q.M., 1997, "Design and kinematics of a parallel manipulator for manufacturing", Manufacturing Technology, Vol. 46, No. 1, pp. 297-300.
17. Yang, P.H., Waldron, K.J., Dutt, V. and Orin, E., 1996, "Design of a three degree of freedom motion platform for a low cost driving simulator", Journal of Applied Mechanics and Robotics, Vol. 3, No. 4, pp. 26-30.