Evaluation of hard coating performance in drilling compacted graphite iron (CGI)

Journal of Materials Engineering and Performance

Volumn 22, Issue 10, 2013, Pages 3155-3160

  De Paiva, José M F ^a   Amorim, Fred L ^b   Soares, P ^b   Torres, Ricardo D ^b  

^a Faculdade de Tecnologia Senai   (Brazil)

^b PONTIFICAL CATHOLIC UNIVERSITY OF PARANÁ   (Brazil)

Author keywords

compacted graphite iron; hard coatings; machining; wear of cutting tools

Indexed keywords

CARBIDES; CUTTING; CUTTING TOOLS; GRAPHITE; IRON; SPEED;

CEMENTED CARBIDE TOOLS; COATING PERFORMANCE; COATING SYSTEM; COMMERCIAL COATINGS; COMPACTED GRAPHITE IRON; CUTTING SPEED; FEED FORCES; HARDER COATINGS; WEAR OF CUTTING TOOL;

HARD COATINGS;

EID: 84887610262     PISSN: 10599495     EISSN: 15441024     Source Type: Journal    
DOI: 10.1007/s11665-013-0601-4     Document Type: Article

References (15)

1. H.K. Toenshoff, W. Spintig, W. Koenig, and A. Neisses, Machining of Holes Developments in Drilling Technology, Ann. CIRP, 1994, 43(2), p 551
2. M.B. da Silva, V.T.G. Naves, J.D.B. Melo, C.L.F. de Andrade, and W.L. Guesser, Analysis of Wear of Cemented Carbide Cutting Tools During Milling Operation of Gray Iron and Compacted Graphite Iron, Wear, 2011, 271, p 2426-2432
3. M. Heck, H.M. Ortner, S. Flege, U. Reuter, and W. Ensinger, Analytical Investigations Concerning the Wear Behaviour of Cutting Tools Used for the Machining of Compacted Graphite Iron and Grey Cast Iron, Int. J. Refract. Met. Hard. Mater., 2008, 26, p 197-206
4. F. Mocellin, E. Melleras, W.L. Guesser, and L. Boehs, Study of the Machinability of Compacted Graphite Iron for Drilling Process, J. Braz. Soc. Mech. Sci. Eng., 2003, 26(1), p 22-27
5. E. Abele, A. Saham, and H. Schulz, Wear Mechanism When Machining Compacted Graphite Iron, CIRP Ann. Manuf. Technol., 2002, 51(1), p 53-56
6. M. Gastel, C. Konetschny, U. Reuter, C. Fasel, H. Schulz, R. Riedel, and H.M. Ortner, Investigation of the Wear Mechanism of Cubic Boron Nitride Tools Used for the Machining of Compacted Graphite Iron and Grey Cast Iron, Int. J. Refract. Met. Hard. Mater., 2000, 18, p 287-296
7. 1-x CrxN Coatings Prepared by Cathodic Arc Evaporation, Surf. Coat. Technol., 2005, 200, p 2114-2122
8. J.L. Endrino, G.S. Fox-Rabinovich, A. Reiter, S.V. Veldhuis, R. Escobar Galindo, J.M. Albella, and J.F. Marco, Oxidation Tuning in AlCrN Coatings, Surf. Coat. Technol., 2007, 201, p 4505-4511
9. J.L. Mo, M.H. Zhu, B. Lei, Y.X. Leng, and N. Huang, Comparison of Tribological Behaviours of AlCrN and TiAlN Coatings - Deposited by Physical Vapor Deposition, Wear, 2007, 263, p 1423-1429
10. E. Le Bourhis, P. Goudeau, M.H. Staia, E. Carrasquero, and E.S. Puchi-Cabrera, Mechanical Properties of Hard AlCrN-Based Coated Substrates, Surf. Coat. Technol., 2009, 203, p 2961-2968
11. F.-R. Weber, F. Fontaine, M. Scheib, and W. Bock, Cathodic arc Evaporation of (Ti, Al)N Coatings and (Ti, Al)N/TiN Multilayer-Coatings - Correlation Between Lifetime of Coated Cutting Tools, Structural and Mechanical Film Properties, Surf. Coat. Technol., 2004, 177-178, p 227-232
12. Shiva. Kalidas, Richard.E. DeVor, and Shiv.G. Kapoor, Experimental Investigation of the Effect of Drill Coatings on Hole Quality Under Dry and Wet Drilling Conditions, Surf. Coat. Technol., 2001, 148, p 117-128
13. W. Kalss, A. Reiter, V. Derflinger, C. Gey, and J.L. Endrino, Modern Coatings in High Performance Cutting Applications, Int. J. Refract. Met. Hard. Mater., 2006, 24, p 399-404
14. G.S. Fox-Rabinovich, B.D. Beake, J.L. Endrino, S.C. Veldhuis, R. Parkinson, L.S. Shuster, and M.S. Migranov, Effect of Mechanical Properties Measured at Room and Elevated Temperatures on the Wear Resistance of Cutting Tools with TiAlN and AlCrN Coatings, Surf. Coat. Technol., 2006, 200, p 5738-5742
15. M.C. Shaw, Metal Cutting Principles, 2nd ed., Oxford University Press, New York, 2005