Finite element simulations of bone temperature rise during bone drilling based on a bone analog

Journal of Medical and Biological Engineering

Volumn 33, Issue 3, 2013, Pages 269-274

  Tu, Yuan Kun ^a   Chen, Li Wen ^c   Ciou, Ji Sih ^c   Hsiao, Chih Kun ^b   Chen, Yung Chuan ^c  

^a NATIONAL CHENG KUNG UNIVERSITY   (Taiwan)

^b E DA HOSPITAL   (Taiwan)

^c NATIONAL PINGTUNG UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Taiwan)

Author keywords

Drill bit; Drilling speed; Finite element model (FEM); Temperature distribution; Thermally affected zone

Indexed keywords

DRILLING PROCESS; DRILLING SPEED; EMPIRICAL EQUATIONS; FINITE ELEMENT SIMULATIONS; METHOD OF ANALYSIS; NUMERICAL RESULTS; TEMPERATURE RISE; THREE DIMENSIONAL FINITE ELEMENT MODEL;

BITS; FINITE ELEMENT METHOD; TEMPERATURE DISTRIBUTION; THERMOCOUPLES;

BONE;

ANIMAL TISSUE; ARTICLE; CORTICAL BONE; DRILL BIT; FINITE ELEMENT ANALYSIS; NONHUMAN; ROTATION; TEMPERATURE; TRABECULAR BONE;

EID: 84883813648     PISSN: 16090985     EISSN: None     Source Type: Journal    
DOI: 10.5405/jmbe.1366     Document Type: Article

References (18)

1. A. R. Eriksson, T. Albrektsson,B.GraneandD.McQueen, "Thermal injury to bone. A vital microscopic description of heat effects," Int. J. Oral Surg., 11: 115-121, 1982.
2. A. R. Eriksson , T. Albrektsson, "Temperature threshold levels for heat-induced bonetissueinjury:A vital-microscopic study in the rabbit," J. Prosthet. Dent. , 50: 101-107, 1983.
3. W. Allan, E. D. Williams , C. J. Kerawala, "Effects of repeated drill use on temperature of bone during preparation for osteosynthesis self-tapping screws," Br. J. Oral Maxillofac. Surg. , 43: 314-319, 2005.
4. M. T. Hillery , I. Shuaib, "Temperature effects in the drilling of human , bovine bone," J. Mater. Process. Technol. , 92-93: 302-308, 1999.
5. M. B. Abouzgia , D. F. James, "Measurements of shaft speed while drilling through bone," J. OralMaxillofac. Surg. ,53: 1308-1315, 1995.
6. L. S. Matthews , C. Hirsch, "Temperatures measured in human cortical bone when drilling," J. Bone Joint Surg. Am. , 54: 297-308, 1972.
7. K. N. Bachus, M. T. Rondina , D. T. Hutchinson, "The effects of drilling force on cortical temperatures , their duration: an in vitro study," Med. Eng. Phys. , 22: 685-691, 2000.
8. G. Augustin, S. Davila, K. Mihoci, T. Udiljak, D. S. Vedrina , A. Antabak, "Thermal osteonecrosis , bone drilling parameters revisited," Arch. Orthop. Trauma Surg. , 128: 71-77, 2008.
9. S. R. H. Davidson , D. F. James, "Drilling in bone: modeling heat generation , temperature distribution," J. Biomech. Eng. , 125: 305-314, 2003.
10. Y. B. Guo , D. A. Dornfeld, "Finite element modeling of burr formation process in drilling 304 stainless steel," J. Manuf. Sci. Eng.-Trans. ASME, 122: 612-619, 2000.
11. Sawbones. Worldwide: ADivision of Pacific Research Laboratories, Inc. Available at http://www. sawbones.com/
12. P.Zioupos and J.D.Currey, "Changes in the stiffness, strength, and toughness of human cortical bone with age," Bone, 22: 57-66, 1998.
13. L. J. Gibson, "The mechanical behaviour of cancellous bone," J. Biomech., 18: 317-328, 1985.
14. D. T. Reilly , A. H. Burstein, "The mechanical properties of corticalbone,"J.BoneJointSurg.-Am.Vol.,56:1001-1022, 1974.
15. SimuliaCorp,Systemes D,ABAQUS/St, ardUser'sManual, RI, UAS: Providence, 2008.
16. A. Mellal, H. W. Wiskot, J. Botsis, S. S. Scherrer and U. C.Belser, "Stimulating effect of implant loading on surrounding bone.Comparison of three numerical models and validation by in vivo data," Clin.Oral Implants Res., 15: 239-248, 2004.
17. C. J. F. Ridders, "Three-point iterationsderived exponential curve fitting," IEEE Trans. Circuits Syst., 26: 669-670, 1979.
18. B.S.Sotto-Maior,E. P. Rocha, E. O.Almeida, A.C. Freitas-Juńior,R.B. Anchieta, A. A.Cury, "Influenceof high insertion torque on implant placement-an anisotropic bone stress analysis," Braz. Dent. J., 21: 508-514, 2010.