A combination of ball milling and high-ratio differential speed rolling for synthesizing carbon nanotube/copper composites

Carbon

Volumn 61, Issue , 2013, Pages 487-500

  Yoo, S J ^a   Han, S H ^b   Kim, W J ^a  

^a Hong Ik University   (South Korea)

^b Korea Institute of Material Science   (South Korea)

Author keywords

[No Author keywords available]

Indexed keywords

COMPOSITE POWDERS; CONVENTIONAL ROLLING; DIFFERENTIAL SPEED ROLLING; DIRECTIONAL ALIGNMENT; GRAIN-SIZE REDUCTION; HIGH-ENERGY BALL-MILLING; LARGE AMOUNTS; STRAIN INDUCED;

MECHANICAL PROPERTIES; POWDERS;

BALL MILLING;

EID: 84879695065     PISSN: 00086223     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.carbon.2013.04.105     Document Type: Article

References (33)

1. M.M.J. Treacy, T.W. Ebbesen, and J.M. Gibson Exceptionally high Young's modulus observed for individual carbon nanotubes Nature 381 1996 678 680
2. Y. Yosida High-temperature shrinkage of single-walled carbon nanotube bundles up to 1600 K J Appl Phys 87 2000 3338 3341
3. S. Berber, Y.K. Kwon, and D. Tománek Unusually high thermal conductivity of carbon nanotubes Phys Rev Lett 84 2000 4613 4616
4. S.R. Dong, J.P. Tu, and X.B. Zhang An investigation of the sliding wear behavior of Cu-matrix composite reinforced by carbon nanotubes Mater Sci Eng A 313 2001 83 87
5. K.T. Kim, S.I. Cha, S.H. Hong, and S.H. Hong Microstructures and tensile behavior of carbon nanotube reinforced Cu matrix nanocomposites Mater Sci Eng A 430 2006 27 33
6. S.I. Cha, K.T. Kim, S.N. Arshad, C.B. Mo, and S.H. Hong Extraordinary strengthening effect of carbon nanotubes in metal-matrix nanocomposites processed by molecular-level mixing Adv Mater 17 2005 1377 1381
7. K.T. Kim, J. Eckert, S.B. Menzel, T. Gemming, and S.H. Hong Grain refinement assisted strengthening of carbon nanotube reinforced copper matrix nanocomposites Appl Phys Lett 92 2008 121901 121903
8. P. Quang, Y.G. Jeong, S.C. Yoon, S.H. Hong, and H.S. Kim Consolidation of 1 vol.% carbon nanotube reinforced metal matrix nanocomposites via equal channel angular pressing J Mater Process Technol 187-188 2007 318 320
9. P. Jenei, E.Y. Yoon, J. Gubicza, H.S. Kim, J.L. Lábár, and T. Ungár Microstructure and hardness of copper-carbon nanotube composites consolidated by high pressure torsion Mater Sci Eng A 528 2011 4690 4695
10. H. Li, A. Misra, Z. Horita, C.C. Koch, N.A. Mara, and P.O. Dickerson Strong and ductile nanostructured Cu-carbon nanotube composite Appl Phys Lett 95 2009 071907 71909
11. W.J. Kim, K.E. Lee, and S.H. Choi Mechanical properties and microstructure of ultrafine-grained copper prepared by a high-speed-ratio differential speed rolling Mater Sci Eng A 506 2009 71 79
12. W.J. Kim, J.B. Lee, W.Y. Kim, H.T. Jeong, and H.G. Jeong Microstructure and mechanical properties of Mg-Al-Zn alloy sheets severely deformed by asymmetrical rolling Scr Mater 56 2007 309 312
13. W.J. Kim, S.J. Yoo, H.T. Jeong, D.M. Kim, B.H. Choe, and J.B. Lee Effect of the speed ratio on grain refinement and texture development in pure Ti during differential speed rolling Scr Mater 64 2011 49 52
14. Y.H. Ji, and J.J. Park Analysis of thermo-mechanical process occurred in magnesium alloy AZ31 sheet during differential speed rolling Mater Sci Eng A 485 2008 299 304
15. H.J. Choi, G.B. Kwon, G.Y. Lee, and D.H. Bae Reinforcement with carbon nanotubes in aluminum matrix composites Scr Mater 59 2008 360 363
16. H.J. Choi, J.H. Shin, and D.H. Bae Grain size effect on the strengthening behavior of aluminum-based composites containing multi-walled carbon nanotubes Compos Sci Technol 71 2011 1699 1705
17. Ph. Gerber, J. Tarasiuk, Th. Chauveau, and B. Bacroix A quantitative analysis of the evolution of texture and stored energy during annealing of cold rolled copper Acta Mater 51 2003 6359 6371
18. M.G. Stout, and J.A. O'Rourke Experimental deformation textures of OFE copper and 70:30 brass from wire drawing, compression, and torsion Metall Trans A 20 1989 125 131
19. P. Delhaes, M. Couzi, M. Trinquecoste, J. Dentzer, H. Hamidou, and C. Vix-Guterl A comparison between Raman spectroscopy and surface characterizations of multiwall carbon nanotubes Carbon 44 2006 3005 3013
20. S. Casiraghi, A.C. Ferrari, and J. Robertson Raman spectroscopy of hydrogenated amorphous carbons Phys Rev B 72 2005 085401 85414
21. C. He, N.Q. Zhao, C.S. Shi, X.W. Du, J.J. Li, and H.P. Li An approach to obtaining homogeneously dispersed carbon nanotubes in Al powders for preparing reinforced Al-matrix composites Adv Mater 19 2007 1128 1132
22. K. Jensen, W. Mickelson, A. Kis, and A. Zettl Buckling and kinking force measurements on individual multiwalled carbon nanotubes Phys Rev B 76 2007 195436
23. Y.M. Wang, and E. Ma Three strategies to achieve uniform tensile deformation in a nanostructured metal Acta Mater 52 2004 1699 1709
24. N. Hansen Hall-Petch relation and boundary strengthening Scr Mater 51 2004 801 806
25. S.R. Bakshi, and A. Agarwal An analysis of the factors affecting strengthening in carbon nanotube reinforced aluminum composites Carbon 49 2011 533 544
26. N.Q. Ching, J. Gubicza, and T.G. Langdon Characteristics of face-centered cubic metals processed by equal-channel angular pressing J Mater Sci 42 2007 1594 1605
27. J. Gubicza, N.Q. Chinh, J.L. Lábár, Z. Hegedüs, C. Xu, and T.G. Langdon Microstructure and yield strength of severely deformed silver Scr Mater 58 2008 775 778
28. H.J. Frost, and M.F. Ashby Deformation mechanism maps 1983 Pergamon Press Oxford p. 21
29. V.C. Nardone, and K.M. Prewo On the strength of discontinuous silicon carbide reinforced aluminum composites Scr Metall Mater 20 1986 43 48
30. W.F. Hosford Mechanical behavior of materials 1st ed. 2005 Cambridge University Press New York pp. 381-382
31. L. Ci, Z. Ryu, N.Y. Jin-Phillipp, and M. Rühle Investigation of the interfacial reaction between multi-walled carbon nanotubes and aluminum Acta Mater 54 2006 5367 5375
32. H. Kwon, M. Estili, K. Takagi, T. Miyazaki, and A. Kawasaki Combination of hot extrusion and spark plasma sintering for producing carbon nanotube reinforced aluminum matrix composites Carbon 47 2009 570 577
33. K. Chu, C.C. Jia, L.K. Jiang, and W.S. Li Improvement of interface and mechanical properties in carbon nanotube reinforced Cu-Cr matrix composites Mater Design 45 2013 407 411