Additive manufacturing of alumina parts by indirect selective laser sintering and post processing

Journal of Materials Processing Technology

Volumn 213, Issue 9, 2013, Pages 1484-1494

  Shahzad, Khuram ^a   Deckers, Jan ^a   Kruth, Jean Pierre ^a   Vleugels, Jef ^a  

^a UNIVERSITY OF LEUVEN   (Belgium)

Author keywords

Additive manufacturing; Alumina; Indirect selective laser sintering; Polymer ceramic microspheres

Indexed keywords

ALUMINA; CERAMIC MATERIALS; COMPOSITE MATERIALS; MANUFACTURE; PHASE SEPARATION; POLYMERS; POLYPROPYLENES; SINTERED ALUMINA; SINTERING;

ADDITIVE MANUFACTURING; POLYMER CERAMIC COMPOSITE; POLYMER CONCENTRATIONS; POST-PROCESSING TECHNIQUES; PREHEATING TEMPERATURE; PRESSURE-LESS SINTERING; SELECTIVE LASER SINTERING; THERMALLY INDUCED PHASE SEPARATION;

LASER HEATING;

EID: 84876701995     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2013.03.014     Document Type: Article

References (15)

1. Ph. Bertrand, F. Bayle, C. Combe, P. Goeuriot, and I. Smurov Ceramic component manufacturing by selective laser sintering Applied Surface Science 254 2007 989 992 (Pubitemid 350138251)
2. J. Deckers, K. Shahzad, J. Vleugels, and J.P. Kruth Cold/Quasi isostatic pressing assisted indirect selective laser sintering of alumina components Journal of Rapid Prototyping 5 2012 409 419
3. D. Drummer, D. Rietzel, and F. Kühnlein Development of a characterization approach for the sintering behavior of new thermoplastics for selective laser sintering Physics Procedia 5 2010 533 542
4. T.J. Gill, and K.K.B. Hon Experimental investigations into the selective laser sintering of silicon carbide polyamide composites Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 218 2004 1249 1256
5. Y.-C Hagedorn, N. Balachandran, W. Meiners, K. Wissenbach, and R. Poprawe SLM of net-shaped high strength ceramics: new opportunities for producing dental restorations Proceedings of Solid Freeform Fabrication Symposium Austin 2011 536-546
6. D. Horák, M. Babič, H. Macková, and M.J. Beneš Preparation and properties of magnetic nano- and microsized particles for biological and environmental separations Journal of Separation Science 30 2007 1751 1772 (Pubitemid 47180279)
7. W.-H. Hou, and T.M. Lobuglio A new technique for preparing monodisperse polymer particle. II. Phase separation mechanisms Journal of Applied Polymer Science 54 1994 1363 1369
8. F. Klocke, C. Derichs, C. Ader, and A. Demmer Investigations on laser sintering of ceramic slurries Production Engineering. Research and Development 1 2007 279 284
9. J.-P. Kruth, G. Levy, F. Klocke, and T.H.C. Childs Consolidation phenomena in laser and powder-bed based layered manufacturing CIRP Annals - Manufacturing Technology 56 2007 730 759 (Pubitemid 350122466)
10. K. Shahzad, J. Deckers, S. Boury, B. Neirinck, J. Vleugels, and J.P. Kruth Preparation and indirect selective laser sintering of alumina/PA miscrospheres Ceramics International 38 2012 1241 1247
11. K. Subramanian, N. Vail, J. Barlow, and H. Marcus Selective laser sintering of alumina with polymer binders Rapid Prototyping Journal 1 1995 24 35
12. X. Tian, D. Li, and J.G. Heinrich Rapid prototyping of porcelain products by layer-wise slurry deposition (LSD) and direct laser sintering Rapid Prototyping Journal 18 5 2012 362 373
13. D. Tscharnuter, M. Jerabek, Z. Major, and G. Pinter Irreversible deformation of isotactic polypropylene in the pre-yield regime European Polymer Journal 47 2011 989 996
14. W.C. Tu, and F.E. Lange Liquid precursor infiltration processing of powder compacts: I. Kinetic studies and microstructure development Journal of the American Ceramic Society 78 12 1995 3277 3288
15. Y. Wu, J. Du, K.-L. Choy, and L.L. Hench Laser densification of powder beds generated using aerosol assisted spray deposition Journal of the European Ceramic Society 27 2007 4727 4735 (Pubitemid 47488007)