Improvement of machinability of Waspaloy via laser-assisted machining

International Journal of Advanced Manufacturing Technology

Volumn 64, Issue 1-4, 2013, Pages 475-486

  Ding, Hongtao ^a   Shin, Yung C ^a  

^a PURDUE UNIVERSITY   (United States)

Author keywords

Laser assisted machining; Surface integrity; Tool wear; Waspaloy

Indexed keywords

AIRCRAFT TURBINE ENGINES; COMPRESSOR DISKS; CONVENTIONAL MACHINING; CUTTING FORCES; HEAT TRANSFER MODEL; HEAT-RESISTANT ALLOY; INFRA-RED CAMERAS; LASER ASSISTED MACHINING; MATERIAL REMOVAL; ROOM TEMPERATURE; SPECIFIC CUTTING ENERGY; SURFACE FINISHES; SURFACE INTEGRITY; SURFACE TEMPERATURE MEASUREMENT; TEMPERATURE PREDICTION; THERMAL MODEL; TOOL WEAR; WASPALOY; WORKPIECE MATERIALS;

ATMOSPHERIC TEMPERATURE; FINISHING; LASERS; SURFACE ROUGHNESS; TEMPERATURE MEASUREMENT; WEAR OF MATERIALS;

THREE DIMENSIONAL;

EID: 84872495455     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-012-4012-8     Document Type: Article

References (34)

1. Klopp WD (ed) (1999) Aerospace structural metals handbook: Waspaloy. Purdue Research Foundation, West Lafayette, Indiana
2. Vander Voort GF (ed) (2004) ASM handbook: metallography and microstructures. ASM International
3. Mannan S, Patel S, deBarbadillo J (2000) Long term thermal stability of INCONEL alloys 718, 706, 909, and WASPALOY at 593 C and 704 C. In: Superalloys 2000. Proceedings of the Ninth International Symposium on Superalloys, 17-21 Sept. 2000, Warrendale, PA, USA, 2000. SUPERALLOYS 2000. Proceedings of the Ninth International Symposium on Superalloys. TMS-Miner. Metals & Mater. Soc, pp 449-458
4. Konig W, Gerschwiler K (1999) Machining nickel-based superalloys. Manuf Eng 122:102-108
5. Noaker PM (1994) When face milling pays off. Manuf Eng 113:73-77
6. Roy AK, Venkatesh A, Marthandam V, Ghosh A (2008) Tensile deformation of a nickel-based alloy at elevated temperatures. J Mater Eng Perform 17:607-611
7. Khamsehzadeh H (1991) Behaviour of ceramic cutting tools when machining superalloys University of Warwick, United Kingdom
8. Shaw MC, Thurman AL, Ahlgren HJ (1965) Plasticity problem involving plane strain and plane stress simultaneously - groove formation in machining of high-temperature alloys. In: ASME Meeting PROD-10, New York, NY, United States, Jun 9-11 1965 1965. American Society of Mechanical Engineers - Papers. American Society of Mechanical Engineers (ASME), p 5
9. Moltrecht KEH. Turning of high temperature alloys. In: 32nd ASTME Annual Meeting, 1964, 1964. ASTME-Collected Papers. p 31
10. Lee M, Horne JG, Tabor D (1979) Mechanism of notch formation at the depth of cut line of ceramic tools machining nickel-based superalloys. Electric Power Research Institute (Report) EPRI EL:460-469.
11. Barrett R, Page TF (1990) The interactions of an Al2O3-SiC-whisker- reinforced composite ceramic with liquid metals. Wear 138(1-2):225-237
12. Narutaki N, Yamane Y, Hayashi K, Kitagawa T, Uehara K (1993) High-speed machining of Inconel 718 with ceramic tools. CIRP Ann Manuf Technol 42:103-106
13. Kitagawa T, Kubo A, Makawa K (1997) Temperature and wear of cutting tools in high-speed machining of Inconel 718 and Ti-6Al-6 V-2Sn. Wear 202:142-148
14. Rozzi JC, Pfefferkorn FE, Incropera FP, Shin YC (2000) Transient, three-dimensional heat transfer model for the laser assisted machining of silicon nitride: I. Comparison of predictions with measured surface temperature histories. Int J Heat Mass Transf 43(8):1409-1424
15. Tian Y, Shin YC (2006) Thermal modeling for laser-assisted machining of silicon nitride ceramics with complex features. Journal of Manufacturing Science and Engineering, Transactions of the ASME 128:425-434
16. Anderson M, Patwa R, Shin YC (2006) Laser-assisted machining of Inconel 718 with an economic analysis. Int J Mach Tool Manuf 46(14):1879-1891
17. Dandekar CR, Shin YC, Barnes J (2010) Machinability improvement of titanium alloy (Ti-6Al-4 V) via LAM and hybrid machining. Int J Mach Tool Manuf 50(2):174-182
18. Anderson MC, Shin YC (2006) Laser-assisted machining of an austenitic stainless steel: P550. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 220:2055-2067
19. Ding H, Shin YC (2010) Laser-assisted machining of hardened steel parts with surface integrity analysis. Int J Mach Tool Manuf 50(1):106-114
20. Skvarenina S, Shin YC (2006) Laser-assisted machining of compacted graphite iron. Int J Mach Tool Manuf 46(1):7-17
21. Kumar AS, Durai AR, Sornakumar T (2006) Wear behaviour of alumina-based ceramic cutting tools on machining steels. Tribol Int 39(3):191-197
22. Richards N, Aspinwall D (1989) Use of ceramic tools for machining nickel based alloys. Int J Mach Tool Manuf 29(4):575-588
23. Lo Casto S, Lo Valvo E, Lucchini E, Maschio S, Piacentini M, Ruisi VF (1999) Ceramic materials wear mechanisms when cutting nickel-based alloys. Wear 225-229, Part 1 (0):227-233.
24. Zhang X, Wu S, Wang H, Liu CR (2011) Predicting the effects of cutting parameters and tool Geometry on hard turning process using finite element method. J Manuf Sci Eng 133(4):041010
25. Liu L, Hirose A, Kobayashi KF (2002) A numerical approach for predicting laser surface annealing process of Inconel 718. Acta Materialia 50(6):1331-1347
26. Dreshfield R (1993) Evaluation of mechanical properties of a low-cobalt wrought superalloy. J Mater Eng Perform 2(4):517-522
27. Ho HS, Risbet M, Feaugas X, Moulin G (2011) Damage mechanism related to localization of plastic deformation of Waspaloy(TM): effect of grain size. Procedia Engineering 10:863-868
28. Pusavec F, Hamdi H, Kopac J, Jawahir IS (2011) Surface integrity in cryogenic machining of nickel based alloy - Inconel 718. J Mater Process Technol 211(4):773-783
29. Attia H, Tavakoli S, Vargas R, Thomson V (2010) Laser-assisted high-speed finish turning of superalloy Inconel 718 under dry conditions. CIRP Ann Manuf Technol 59(1):83-88
30. Ding H, Shin YC (2012) Dislocation density-based modeling of subsurface grain refinement with laser-induced shock compression. Comput Mater Sci 53(1):79-88
31. Lee W-S, Lin C-F, Chen T-H, Chen H-W (2011) Dynamic mechanical behaviour and dislocation substructure evolution of Inconel 718 over wide temperature range. Mater Sci Eng, A 528(19-20):6279-6286
32. Ding H, Shen N, Shin YC (2011) Modeling of grain refinement in aluminum and copper subjected to cutting. Comput Mater Sci 50(10):3016-3025
33. Hirose A, Arita Y, Nakanishi Y, Kobayashi KF (1996) Decrease in hydrogen embrittlement sensitivity of INCONEL 718 by laser surface softening. Mater Sci Eng, A 219(1-2):71-79
34. Liu L, Zhai C, Lu C, Ding W, Hirose A, Kobayashi KF (2005) Study of the effect of [delta] phase on hydrogen embrittlement of Inconel 718 by notch tensile tests. Corros Sci 47(2):355-367